HCMOS器件γ辐射损伤电路分析

本文对最基本的HCMOS器件(反相器和与非门)作了γ辐射损伤实验。通过器件性能变化,分析了γ辐射对电路的作用。     

Ф16mm、Ф18mm钼棒的研制

采用等静压制法，压制钼圆棒坯，经中频高温烧结，制得尺寸适合、用户满意的钼电极棒。     

IC—V100电台锁相环频率合成器

本文从频率合成器的结构、功能入手,详细阐述了频率编程的原理及方法。     

Effect of pretreatments and freezing rate on the firmness of potato tissue after a freeze–thaw cycle

The texture of potato tissue after a freeze–thaw process using different freezing rates and different pretreatments was analysed, in order to select the best strategy for optimum preservation of the textural characteristics of pre‐frozen potato. Ten blanching conditions were tested and a two‐step blanching process with calcium chloride (0.07 g mL^?1) proved the most effective in protecting the tissue after a freeze–thaw process (maximum load force around 10–55% of the raw tissue, depending on potato batch, for air‐blast freezing and 20–60% for immersion freezing). Vacuum impregnation at 100 and 400 mbar, even when followed by different pre‐drying treatments to remove excess water, was very detrimental to resistance to a freeze–thaw process (maximum load force below 10% of the raw tissue for air‐blast freezing and below 20% for immersion freezing). Microstructure analysis confirmed better tissue integrity retention with ethyleneglycol immersion freezing instead of air‐freezing. Differences were found between batches with a 6‐month difference in storage time, indicating that the fresher batch was more suitable for freezing.     

Frequency response function of magnetic bearings using high-temperature superconductor

A high-temperature superconductor YBa₂Cu₃O_7-x with strong pinning force has allowed stable magnetic suspension with no control to be developed. Two types of superconducting magnetic bearings (SMB) using YBCO and permanent magnet were assembled. The two types are radial and axial. The dynamic stiffness of each SMB as it was cooled down under a magnetic field by liquid nitrogen was measured both radially and axially. As a result, it was found that the spring constants of these SMBs were almost as large as a practically desirable value; however, their damping coefficients were lower than the practical level. These findings are useful as one of the data bases for development of an optimum SMB design to support the weight of rotors in an axial direction.     

Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

“双储”模式下的节能控制在小区供水系统中的应用

根据城市居民对供水的可靠性、稳定性、经济节能性的需求,课题组提出了一种基于"双储"模式的供水系统,并按照本市德胜住宅小区的供水要求,设计了一套由储水池、气压罐、变频器、多台水泵机组等主要设备构成的全自动变频恒压供水系统.经过近半年的运行测试,系统有效地解决了传统供水方式中存在的问题,增强了系统的总体性能,有明显的节能效果.     

基于PLC的缸体加工机床控制系统

对可编程控制器（PLC）应用于某设备缸体加工专用机床控制系统的设计思路作了介绍，对系统的硬件组成和软件设计作了较为详细的阐述，通过上位监控计算机可对生产现场的设备状态实施监控和对现场参数进行调整。     

Preparation and characterization of GaN films grown on Ga-diffused Si （111） substrates

Hexagonal GaN films were prepared by nitriding Ga2O3 films with flowing ammonia. Ga2O3 films were deposited on Ga-diffused Si (111) substrates by radio frequency (r.f.) magnetron sputtering. This paper have investigated the change of structural properties of GaN films nitrided in NH3 atmosphere at the temperatures of 850, 900, and 950℃ for 15 min and nitrided at the temperature of 900℃ for 10, 15, and 20 rain, respectively. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS) were used to analyze the structure, surface morphology and composition of synthesized samples. The results reveal that the as-grown films are polycrystalline GaN with hexagonal wurtzite structure and GaN films with the highest crystal quality can be obtained when nitrided at 900℃ for 15 min.