Magnetic field dependence of shielding current density in Y-Ba-Cu-O rings at 77 K

A method for contactless measurement of the shielding critical current density and its dependence on the external magnetic field is described and analyzed. The obtained values are compared with those measured resistively on two different samples. It is shown that the shielding critical current densityJ _cs and the intergranular transport current densityJ _cr are identical if the measurement conditions are similar. A degradation ofJ _cs measured in the external field with AC ripple has been observed.     

Effect of processing history on the properties of Ag-based tapes

The Bi-system tapes and coils were prepared by the powder-in-tube method. The effect of processing and heat treatment on the properties of the tapes and coils was studied. It is found that the shearing stress produced by the rolling process may destroy the 2223 phase, and the destroyed 2223 phase cannot be recovered by heat treatment, whereas the pressing stress produced by the uniaxial pressing process only makes the 2223 phase grains break, and the broken 2223 phase can be closed by the heat treatment. TheJ _c values of the rolling samples, pressing sample, and the coil with a diameter of 35 mm are over 1.3×10⁴, 2.5×10⁴, and 4×10³ A/cm² (77 K, 0 T), respectively.     

Application of a Three-dimensional Wind Driven Circulation Model to Assess the Locations of New Drinking Water Intakes in Lake Ontario

A 3D transport model is used to perform a comparative analysis of several potential drinking water intakes located along the northwest shore of Lake Ontario between Toronto and Oshawa. The model is specifically used to assess each intake under both long- and short-term transport of a potential pollutant release from the Pickering Nuclear Generating Station and potential and actual pollutant releases from local land sources respectively. A model based on a 500 m grid resolution is calibrated using data collected in the aftermath of the 1992 tritium spill at the Pickering Nuclear Generation Station and subsequently used to simulate long-term transport. A model based on a 100 m grid resolution is verified using drogue studies and used to simulate short-term transport events. Both models are used to assess pollutant levels at each of nine potential intake locations under different wind scenarios and pollutant releases. Field data for the study included water quality and flow measurements from local sewers and rivers, and estimates of pollutant levels from the local waste water treatment plants. This paper describes the model setup for both the long-term and short-term transport models, calibration using field data, long-term transport modeling, short-term transport modeling, and the comprehensive analysis approach used to evaluate the nine potential intake locations proposed. Results indicated that four intakes in particular outperformed other intake locations by maintaining bottom pollutant levels within governmental standards and warning times that exceeded 20 hours.     

A novel method of suppressing the inrush current of transformers by using a series‐connected voltage‐source PWM converter

This paper proposes a novel method of suppressing the inrush current of transformers. A small‐rated voltage‐source PWM converter is connected in series to the transformers through a matching transformer. As the connected PWM converter serves as a resistor for the source current, no inrush phenomena occurs. The required rating of the PWM converter, which serves as the damping resistor for the inrush phenomena, is 1/400 that of the main transformers in single‐phase circuits. In three‐phase circuits, it is 1/900. The basic principle of the proposed method is discussed. Digital computer simulation is implemented to confirm the validity and excellent practicability of the proposed method using the PSCAD/EMTDC. A prototype experimental model is constructed and tested. The experimental results demonstrate that the proposed method can perfectly suppress the inrush phenomena. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 157(4): 56–65, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20174     

A novel robust current control approach using adaptive line enhancer for three‐phase current‐source active power filter

An effective system control method is presented for applying a three‐phase current‐source PWM converter with a deadbeat controller to active power filters (APFs). In the shunt‐type configuration, the APF is controlled such that the current drawn by the APF from the utility is equal to the current harmonics and reactive current required for the load. To attain the time‐optimal response of the APF supply current, a two‐dimensional deadbeat control scheme is applied to APF current control. Furthermore, in order to cancel both the delay in the two‐dimensional deadbeat control scheme and the delay in DSP control strategy, an Adaptive Line Enhancer (ALE) is introduced in order to predict the desired value three sampling periods ahead. ALE has another function of bringing robustness to the deadbeat control system. Due to the ALE, settling time is made short in a transient state. On the other hand, total harmonic distortion (THD) of source currents can be minimized compared to the case where ideal identification of the controlled system can be made. The experimental results obtained from the DSP‐based APF are also reported. The compensating ability of this APF is very high in accuracy and responsiveness although the modulation frequency is rather low. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(1): 50–61, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20014     

Electrical conductivity in iodine-doped ethyl cellulose

The electrical conductivity of solution-grown ethyl cellulose (EC) films, 5–30 μm thick, has been studied in the sandwich configuration (metal–EC–metal) as a function of iodine concentration from 0.5 to 5.0 wt% ratio. The studies were conducted in the temperature range 333–383 K, while the field was varied over the range (3.0–5.5) × 10⁴V/cm. Aluminium was used as the lower electrode, while the upper electrode was of Al, Ag, Cu, Au or Sn. Certain transient effects such as a large burst of current immediately after the application of field were observed. An attempt was made to identify the nature of the current by comparing the observed dependence on electric field, electrode material and temperature with the respective characteristic features of the existing theories of electrical conduction. The results show that the electrical conduction follows Ohm's law at lower fields, while at higher fields, space-charge limited current (SCLC) was observed. It was also found that Richardson–Schottky emission was responsible, to some extent, for the transport of charge carriers in the polymer. The conductivity of the films increased on doping with iodine. The dopant molecules are considered to act as additional trapping centes and provide links between the polymer molecules in the amorphous region, thus resulting in the formation of charge transfer complexes.     

A simplified cascade current‐source inverter interconnected to a single‐phase three‐wire distribution system and its application to electric energy storage systems with batteries

A novel current source inverter system interconnected to the single‐phase grid is proposed. It has the same construction as the conventional three‐phase current source inverter that is interconnected to the single‐phase three‐wire distribution system. Though the proposed circuit has no output transformer, it can be equivalently performed as the single‐phase double cascade inverter by diverting the pole transformer in the utility system. By controlling the appropriate scheme, the output currents can be obtained as the five‐level waveforms and their distortions can be decreased sufficiently. It is applied to the interactive electric energy storage system with batteries and the basic discharging characteristics are discussed experimentally. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(2): 50–61, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10380     

智能投币机在城市公交上使用的改进分析

通过鱼骨图的方法对现有智能公交投币机存在识别率偏低的问题进行了分析,提出在智能投币机中采用闭式五角叶轮或增加硬币预处理部分,对现有的智能公交投币机进行改进,使智能公交投币机的硬币辨识率得到提高.     

Towards inverse modeling of turbidity currents: The inverse lock-exchange problem

A new approach is introduced for turbidite modeling, leveraging the potential of computational fluid dynamics methods to simulate the flow processes that led to turbidite formation. The practical use of numerical flow simulation for the purpose of turbidite modeling so far is hindered by the need to specify parameters and initial flow conditions that are a priori unknown. The present study proposes a method to determine optimal simulation parameters via an automated optimization process. An iterative procedure matches deposit predictions from successive flow simulations against available localized reference data, as in practice may be obtained from well logs, and aims at convergence towards the best-fit scenario. The final result is a prediction of the entire deposit thickness and local grain size distribution. The optimization strategy is based on a derivative-free, surrogate-based technique. Direct numerical simulations are performed to compute the flow dynamics. A proof of concept is successfully conducted for the simple test case of a two-dimensional lock-exchange turbidity current. The optimization approach is demonstrated to accurately retrieve the initial conditions used in a reference calculation.