Breakdown characteristics of oil and paper insulation for a very fast transient voltage

This paper describes the dielectric breakdown characteristics of oil and oil‐impregnated paper for very fast transient (VFT) voltages. Blumlein circuits generate VFT voltages of 60 and 300 ns in a pulse width that simulates disconnecting switching surges in gas‐insulated switch gears. We measured the breakdown voltages of needle‐to‐plane, plane‐to‐plane oil gaps and several pieces of paper between plane electrodes for VFT and lightning impulse voltages. The measured data were formulated in V‐t characteristics and Weibull probability distributions. The inclination n of V‐t characteristics of insulating paper is 150, which is less than n = 13.7 of the plane‐to‐plane oil gap in the VFT time range. The shape parameters of Weibull distribution obtained in this study show that the scattering of breakdown voltages of paper is much less than that of oil. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 141(4): 16–24, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10043     

Water-soluble copolymers: 22. Copolymers of acrylamide with 2-acrylamido-2-methylpropanedimethylammonium chloride: Aqueous solution properties of a polycation

The viscometric, turbidimetric and potentiometric properties of copolymers of acrylamide (AM) with 2-acrylamido-2-methylpropanedimethylammonium chloride (AMPDAC) were studied in aqueous solutions. The AMPDAC polymers exhibit poor salt tolerance and large, negative viscosity/temperature coefficients. Furthermore, the polymers were found to be sensitive to changes in pH. The AMPDAC polymers undergo phase separation in the presence of dianions as a function of temperature and AMPDAC composition.     

Paste Residence Time in a Spouted Bed Dryer. II: Effect of Spout Operational Conditions

Residence time distributions for an aqueous solution of 10% sodium chloride in a spouted bed dryer of inert particles were determined using the stimulus-response technique. Glass and polyethylene beads with diameters 2.6 and 3.4 mm were used as inert bodies in a cylindrical column of 14.0 cm diameter and 60° conical base. The effects of inert bodies load, air, and paste flow rates on the mean residence times and RTD were determined following 2³ factorial designs. The RTD could be correlated to the perfect mixing cell model with R² varying from 0.8684 to 0.9815. The mean residence times in CSBD varied from 10.8 to 13.9 and 10.7 to 13.3 min for glass and polyethylene beads, respectively. For both inert particles, mean residence times increased with bed height and decreased with paste feed rates. Also, terms of interaction among the factors were significant in some cases, showing a complex behavior of paste residence times. Equations obtained by response surface regression could predict mean residence times on glass and polyethylene beads with deviations lower than ±10%.     

Phase equilibria of quasi-binary systems consisting of multicomponent polymers 1 and 2. IV: Poly(ethylene oxide)/poly(propylene oxide) systems

To confirm the reliability of the theory of phase equibria of multicomponent polymer 1/multicomponent polymer 2 systems (i.e. quasi-binary systems) and the method of computer experiment based on this theory (Brit. Polym. J., 23 (1990)285; 23 (1990)299; Polym. Int., 29 (1992)219), could point curves (CPC), two-phase volume ratios ( R ) and critical solution points (CSP) have been determined experimentally for the quasi-binary mixtures of poly(ethylene oxide) (M¯_w = 647, M¯_w/M¯_n = 1.15; M¯_w and M¯_n, the weight-average and numberaverage molecular weights, respectively) and poly(propylene oxide) (M¯_w = 2028, M¯_w/M¯_n = 1.08; and M_w = 2987, M_w/M_n = 1.13). The hydroxyl end groups of both polymers were methoxylated in advance by the Cooper & Booth method (Polymer, 18 (1977)164). The thermodynamic interaction parameter between both polymers, χ₁₂, and the concentration dependence parameters for the above quasi-binary systems were determined by the method proposed in a previous paper (Brit. Polym. J., 23 (1990)299). CPC, R and CSP values calculated on the basis of the theory are in good agreement with the values determined experimentally.     

Synthesizing plans that contain actions with context-dependent effects1

This paper presents a method of solving planning problems that involve actions whose effects change according to the situations in which they are performed. The approach is an extension of the conventional planning methodology in which plans are constructed through an iterative process of scanning for goals that are not yet satisfied, inserting actions to achieve them, and introducing subgoals to these actions. This methodology was originally developed under the assumption that one would be dealing exclusively with actions that produce the same effects in every situation. The extension involves introducing additional subgoals to actions above and beyond the preconditions of execution normally introduced. These additional subgoals, called secondary preconditions, ensure that the actions are performed in contexts conducive to producing the effects we desire. This paper defines and analyzes secondary preconditions from a mathematically rigorous standpoint and demonstrates how they can be derived from regression operators.     

Homogenization of hardness distribution and distortion in high pressure gas quenching

Quenching with gases rather than oil or other liquid media has the advantages of reducing the risks concerning health and environment, while simultaneously homogenizing the quenching results and minimizing distortion due to a wide range of possible process parameter variations and the pure convective heat transfer. In this contribution, a coupled solution for increasing homogenization of quenching results within high pressure gas quenching will be presented. In the first stage, an experimental test facility was set up for flow investigations and in the second stage a numerical simulation model was generated. The numerical and experimental results of the flow through the chamber were compared for several boundary conditions. Finally, after complete verification of the simulation, the model may be used to assist in parameter variation for optimization of homogeneous high pressure gas quenching.     

Thermal and thermoelastic properties of fast extrusion furnace (FEF) carbon black loaded SBR vulcanizates

The effect of FEF carbon black as filler on the thermal capacity c, diffusivity a, and thermal conductivity λ, of styrene butadiene rubber (SBR) composites in the temperature range 300–420 K was studied. The filler strongly increases the thermal diffusivity, whilst strongly decreasing the thermal capacity and the thermal conductivity (except at high FEF content ≥80 phr). The influence of the filler on the thermoelastic behaviour of the same composites was also investigated. It was found that the thermoelastic temperature change (ΔT) increased with carbon black concentration as well as the entropy change per unit extension.     

Pervaporation performance analysis and prediction—using a hybrid solution-diffusion and pore-flow model

A hybrid mathematic model for pervaporation is proposed which incorporates the concepts of solution-diffusion model and pore model. The model allows performance prediction as well as the establishment of the internal concentration and pressure profiles within the membrane. The model parameters specific to the particular membrane and mixture system are determined using liquid sorption and pervaporation experimental data. The model is experimentally examined using ethanol–water mixtures and poly(dimethyl siloxane)–poly(vinyldiene fluoride) (PDMS–PVDF) composite membranes. The characteristics of flux and separation factor predicted using the model are in fair agreement with the experimental data under various feed concentrations and downstream pressures for different membrane arrangements, including single-layer, reverse single-layer and double-layer PDMS–PVDF composite membranes. Internal profiles of pressure, concentration and component mole fraction can be established using the model. Concentration polarization phenomena for ethanol and water are located at membrane interfaces and vapor–liquid interfaces, respectively. Performances of several different membrane designs are compared using the model.     

Influence of the composition of the binder and the carbonation on the zeta potential values of hardened cementitious materials

Electroosmotic experiments have been carried out on eight different mixes of hardened cementitious matrixes including concrete, mortar and pastes, different types of binders, carbonated and non-carbonated specimens and different test conditions. From these trials, the zeta potential values have been determined and the optimum experimental parameters and devices have been established. In addition, the influence of the composition of the binder on the zeta potential has been quantified indicating that higher amounts of Al₂O₃ in the binder lead to higher positive values of zeta potential, while the SiO₂ acts just on the opposite side. This has been explained in terms of the different i.e.p. (isoelectric point) for both oxides. Concerning the influence of carbonation, it increases the absolute value of the zeta potential toward more negative values; this behaviour has been attributed to the influence of the specifically adsorbed Ca²⁺ in the negative sites of the surface in the non-carbonated samples.     

酸性镀锡液的新进展

从近几年美国发明专利的角度扼要综述酸性镀锡液的新进展。说明酸性镀锡液由氟硼酸盐型发展为烷基磺酸盐型的改进过程。列出参考文献９篇。