Modeling of Diffusion in Capillary Porous Materials During the Drying Process

This paper presents a model of heterogenous diffusion in capillary porous materials during the process of drying. The governing heat and mass transfer equations have been established using the liquid as well as vapor flow. Two models have been presented. Model 1 does not consider the heat conduction while the model 2 has been established by considering the conduction. The developed models and the numerical solutions of the resulting differential equations can take into account the moisture and temperature dependent thermophysical properties of the product. All equations have been established in spherical coordinates but the programme written for the purpose of calculations can be used for other geometries also. Numerical calculations have been performed for gas concrete and tiles using model 1, while model 2 has been used for gas concrete only because of the lack of data for thermophysical properties of the tile. For gas concrete it was seen that conduction has only marginal effect on the drying process and the numerical predictions of the drying process were reasonably accurate.     

Residual stresses and transformation toughening in MoSi2 composites reinforced with partially stabilized zirconia

The results of study of the effects of yttria stabilization (0–6 mol.%) on the room-temperature fracture behavior and toughening mechanisms in zirconia-reinforced MoSi₂ are presented in this paper. Transformation toughening is shown to occur only in composites reinforced with zirconia particles stabilized with 2 mol.% yttria. However, the fracture toughness levels are comparable in the other composites with yttria levels between 0 and 6 mol.%. Toughening in the other composites is attributed to the combined effects of residual stress, microcrack shielding/anti-shielding and/or crack deflection. A rigorous micromechanics-based model is presented for the estimation of residual stress levels in brittle materials reinforced with phases that can transform during cooling or under stress. The model is applied successfully to the rationalization of the observed fracture and toughening phenomena.     

Measurement and prediction of pressure drop in two-phase flow

Experimental data for air–water two-phase co-current flow in two different pipe diameters were used to test the prediction of pressure drop by a number of existing theories and correlations. Several models are shown to be useful for prediction, particularly with the stratified regimes which have proved difficult to handle in the past. The model suggested by Olujic proved to be of particular value.     

Schäden durch kerbinduzierte Schwingbrüche

Failures by notch induced fatigue fractures Notches produce local stress concentrations and promote the formation of fatigue cracks. Characteristic types of notches as a result of design, manufacturing and operation are presented and remedial measures are discussed. Examples demonstrate the effect of different kinds of notches on various components.     

Thermomechanical stress fields in high-temperature fibrous composites. I: Unidirectional laminates

This two-part paper presents a closed-form procedure for evaluation of estimates of local thermomechanical stress fields in two-phase fibrous composites and laminates. The first part is concerned with a unidirectional elastic laminate subjected to uniform mechanical loads and to uniform changes in temperature. Both phases are assumed to be elastic, with temperature-dependent moduli and expansion coefficients; the solution reflects the influence of thermomechanical interactions. Exact solutions are not possible for any real system, because the local geometry is not known in detail. Instead, estimates of the fields are found from a modified Mori-Tanaka approximation. Examples are presented for two SiC/Ti---Al---Nb composites. Local stresses of interest are found after cooling from fabrication to room temperature. The presence of local yielding, and the influence of coupling terms on the local stress magnitudes are examined. Extension of the results to laminated plates is presented in Part II (Dvorak, G.J., Chen, T. & Teply, J., Composites Science and Technology, 43 (1992) 359–368, this issue).     

面流消能近底紊动流速特性的研究(面流消能试验研究之一)

本文主要论述了面流消能五种典型流态近底紊动流速特性,总结出了近底时均流速和紊动强度沿程变化规律,提出了近底紊动流速可能出现的最大瞬时值及相应位置的计算公式。面流消能工程的下游防冲设计中考虑的主要水力参数之一是,消能段近底流速紊动可能出现的最大瞬时值及其相应的部位,但目前国内外研究成果较少。笔者通过水工模型试验重点研究了面流消能各典型流态近底流速及其紊动纵向分量沿程的变化规律,并提出了计算公式,为优化面流设计提供科学依据。     

Longitudinal elastic waves in columns due to earthquake motion

An analysis is presented of longitudinal waves in a thin elastic column. Velocity is specified at one end, and the boundary condition at the other end is expressed in terms of a range of effective impedances of an attached structure. Propagation, reflection and interference of the waves are followed by the method of characteristics. Integration of differential equations along characteristics yields the wave-induced stress, which is then applied to problems of earthquake excitation. Numerical examples are given for recorded updown ground motion of the Kobe Earthquake.     

Effect of Channel Changes in the St. Clair River During the Present Century

Periodic man-made changes in the outlet of Lake Huron through the St. Clair River date back to the middle of the last century. These artificial channel changes have been well documented during the present century. They consist of dredging for commercial gravel removal in the upper river during 1908–25 and uncompensated navigation improvements for the 7.6-m (25-ft) and 8.2-m (27-ft) projects completed in 1933 and 1962, respectively. The total effect of these changes on the levels of Lakes Michigan and Huron (hydraulically one lake) and on the upper St. Clair River profile was determined with dynamic flow models. The ultimate effect of the above dredging was a permanent lowering of the Lake Michigan-Huron levels 0.27 m (0.89 ft), which represents a tremendous loss of freshwater resource [32 km³ (7.7 mi³)].     

Yeast exo-β-glucanases can be used as efficient and readily detectable reporter genes in Saccharomyces cerevisiae

Yeast exo-1,3-β-glucanases are secretable proteins whose function is basically trophic and may also be involved in cell wall glucan hydrolytic processes. Since fluorescein di(β-D -glucopyranoside) is a fluorogenic substrate detectable and quantifiable by flow cytometry, it was used for testing the ability of the EXG1 gene product of Saccharomyces cerevisiae and its homologous gene in Candida albicans to function as reporter genes. These open reading frames were coupled to different promoters in multicopy plasmids, and exoglucanase activity quantified at flow cytometry. Exoglucanases were found to be useful tools for the study of promoter regions in S. cerevisiae. This technique has the advantage over other reporter gene systems—such as β-galactosidase fusions—that it does not require permeabilization of yeast cells and therefore it allows the recovery of viable cells—by sorting—after flow cytometry analysis.