Effects of hydrolysis on the physical properties of short glass-fibre reinforced poly(ethylene terephthalate)

The mechanical fracture strength and toughness of short-fibre composites, injection moulded from compounds of poly(ethylene terephthalate) (PET) containing 10 and 30% (by weight) (w/o) glass, have been investigated and the dependence upon matrix hydrolytic stability determined. Mouldings have been characterised by several physical techniques to evaluate molecular weight, degradation rates, crystallinity and morphology, whilst time-dependent gravimetric data were derived to quantify sorption kinetics and allow comparisons with theoretical reaction rates to be made. During melt processing, PET is hydrolysed extremely rapidly by traces of moisture (<0.02w/o). yet the inherent strength of moulded composites declines significantly only below an apparently critical molecular weight. However, on long-term humid ageing in hot water, impact behaviour especially is rendered more complex by simultaneous crystallisation, molecular reorder and losses of interfacial bond strength.     

Thermal Evaluation of Scorched Graphite-Epoxy Panels by Infrared Scanning

A simple measurement system is described for evaluating damage to graphite-epoxy panels, such as those used in high-performance aircraft. The system uses a heating laser and infrared imaging system to measure thermal performance. Thermal conductivity or diffusivity is a sensitive indicator of damage in materials, allowing this thermal measurement to show various degrees of damage in graphite-epoxy composites. Our measurements track well with heat-flux damage to graphite epoxy panels. This measurement system, including analysis software, could easily be used in the field, such as on the deck of an aircraft carrier or at remote air strips.     

Thermomechanical stress fields in high-temperature fibrous composites. I: Unidirectional laminates

This two-part paper presents a closed-form procedure for evaluation of estimates of local thermomechanical stress fields in two-phase fibrous composites and laminates. The first part is concerned with a unidirectional elastic laminate subjected to uniform mechanical loads and to uniform changes in temperature. Both phases are assumed to be elastic, with temperature-dependent moduli and expansion coefficients; the solution reflects the influence of thermomechanical interactions. Exact solutions are not possible for any real system, because the local geometry is not known in detail. Instead, estimates of the fields are found from a modified Mori-Tanaka approximation. Examples are presented for two SiC/Ti---Al---Nb composites. Local stresses of interest are found after cooling from fabrication to room temperature. The presence of local yielding, and the influence of coupling terms on the local stress magnitudes are examined. Extension of the results to laminated plates is presented in Part II (Dvorak, G.J., Chen, T. & Teply, J., Composites Science and Technology, 43 (1992) 359–368, this issue).     

Asbestos replacement aspects: Modification of the fibre-matrix interphase in lonomer based composites

Asbestos fibres, of the chrysotile variety, and chopped carbon fibres were pretreated by an in-situ polycondensation technique eventually resulting in a polyamide coating on the fibre surface. Ionomer based composites containing either carbon or asbestos fibres in random in plane fibre orientation were prepared, and the influence of this coating process on the tensile properties was investigated. It was found that for the asbestos-filled composites the presence of the nylon 6,6 interlayer improves the tensile performance, especially at moderate polyamide depositions. This is not the case with the pretreated carbon-filled composites for which carbon fibres with higher polyamide contents are preferred. Combinations of the treated asbestos fibres with carbon and/or aramid fibres may be used to reduce the asbestos content in asbestos-only based engineering plastics.     

Solving regularized least squares with qualitatively controlled adaptive cross‐approximated matrices

The adaptive cross‐approximation (ACA) technique is applied to accelerating an inverse‐problem solver that estimates charge distribution on a dielectric spacer. The ACA generates an approximated system‐matrix that enables us to carry out high‐speed inverse calculation. We designed an approximation procedure based on ACA with some additional concepts, that is, (a) partitioning of matrix based on algebraic information, (b) approximation quality control based on matrix norms, and so on. The tested solver (LSQR for regularized least squares) with ACA demonstrates about 10 times faster performance than that without ACA. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 159(3): 10–18, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20326     

3^n阶矩阵乘法的分块算法

针对３＾ｎ阶矩阵的乘法运行，给出了一种分块算法，其乘法运行量比常规的矩阵乘法计算方法和补零的基－２算法都有所减少。     

TFT有源矩阵α－Si∶H薄膜PECVD淀积工艺研究

分析了α－Ｓｉ∶Ｈ薄膜的质量和厚度对α－Ｓｉ∶ＨＴＦＴ关键性指标的影响，深入、详细地讨论了其ＰＥＣＶＤ淀积工艺，并在实验的基础上确定了最佳淀积工艺参数，从而获得了高性能的７５ｍｍ３７２×２７６像素α－Ｓｉ∶ＨＴＦＴ有源矩阵     

石英砂的相变与换向器套筒铸件的变形

用呋喃树脂石英砂工艺生产牵引电机换向器套筒出现变形、裂纹等铸造缺陷,是由石英砂相变膨胀引起,后用高铬刚玉砂代替石英砂得到解决.     

Kynar—500涂装工艺与涂层性能研究

介绍了Kynar－500涂料的涂装工艺，并对涂层的性能作了试验与分析。