The radiation crosslinking and scission of ethylene-propylene copolymers studied by solid-state nuclear magnetic resonance

Methyl groups from chain scission and H-crosslinks have been identified by solid-state nuclear magnetic resonance in amorphous ethylene-propylene copolymers containing 23 and 36 mole % propylene after γ-irradiation to 10 MGy at 30°C. G (scission) and G (crosslink) values determined from the n.m.r. spectra and by extraction are in agreement, which suggests that the crosslinks are not clustered. This may differ from the situation in polyethylene where there is a substantial crystalline content. G(S). G(X) and the ratio G(S)/G(X) increase with increasing propylene content of the copolymers.     

Impedance spectroscopy study of hardened Portland cement paste

In this paper, the differential impedance analysis (DIA) has been applied to the study of the dielectric properties of hardened Portland cement paste. Two time constants are found in the impedance spectra obtained in the frequency region form 100 kHz to 15 MHz. One time constant has been attributed to the solid matrix and the other one to the liquid phase filling the pores. The effect of the cement paste-electrodes interface has been quantified using two different experimental set-ups. Measurements using direct contact between electrodes and cement paste have been compared with measurements using an air gap technique in which the specimen “floats” between the electrodes. The two referred time constants have been found in both types of measurements. The influence of drying on the dielectric parameters is also studied.     

Application of a.c. impedance technique to the study of the proton diffusion process in the porous MnO2 electrode

The proton diffusion coefficient in γ-MnO₂ at various stages of discharge of an electrolytic manganese dioxide electrode has been determined taking into consideration the true molar volume and the electrochemically accessible surface area of MnO₂. The unique electrochemical cell which allows the electrode expansion during the discharge to be monitored in situ was reported. The a.c. impedance technique and the transmission line equivalent circuit were used. Electrode ohmic resistance, Faradaic resistance, and double-layer capacitance were also obtained by means of numerical fitting of the impedance data using the transmission line model.     

铝电解槽热平衡测试计算中的几点问题

由于缺乏正规的标准，铝电解槽能量平衡测试中存在着一些概念混淆、计算方法和公式错误的情况，应引起测试工作者的注意，在测试计算前应认真制订方案，多查一些参考资料，核实所用公式、数据，避免发生失误。同时对于类似计算，由于计算机的应用，应尽可能采取精确算法。没必要采取一些非常粗糙的近似算法和经验值。     

Monitoring Moisture Uptake and Delamination in CFRP-Reinforced Concrete Structures with Electrochemical Impedance Sensors

Electrochemical impedance spectroscopy (EIS) sensors have been used to inspect carbon fiber reinforced polymer (CFRP) -reinforced concrete structures exposed to a variety of test conditions. Similar specimens were also used to investigate the detection of delamination between the CFRP and the concrete using a modified wedge test configuration. The use of external electrodes attached to the CFRP surface, coupled with the embedded rebar, provided the best results. Equivalent circuit modeling was used to analyze the impedance spectra. Several circuit parameters, especially the capacitance and constant phase element (CPE) magnitude, correlated very well with both bonded area/delamination and moisture. Both parameters exhibit a linear relationship with delamination area. The capacitance also showed a linear relationship with moisture content while the CPE was more strongly dependent on moisture. Differences in the response of the specimens subjected to the different exposure conditions were seen and explained based on the moisture uptake of the various specimens.     

3G网络基站电磁环境影响分析

通过资料收集、理论预测、数据监测与分析,讨论了辽宁某市3G网络基站中典型基站的电磁环境。结果表明,理论预测与实际监测结果差距不大,各典型基站的电磁辐射功率密度均低于国家标准限值8μW/cm2,对该地区的电磁环境影响不大。对保护环境提出了相应的对策措施.     

铁尾矿为原料微波法制备介孔分子筛

以鞍山铁尾矿为硅源,CTAB为模板剂,采用微波辐照法合成出全硅介孔分子筛MCM-41。用N2低温吸附、FT-IR、XRD和TEM等表征手段考察了其比表面积、孔径分布、晶体形貌等特性。结果表明:微波辐射法合成的MCM-41分子筛诱导期极短,晶化速度很快,具有典型的按六方对称性排列的孔道结构,FT-IR证明了分子筛具有硅氧四面体骨架。     

Recombination luminescence from defects in boron-ion implantation-doped diamond using low fluences

 Two identical, high purity, natural type IIa diamonds, which displayed the ubiquitous blue cathodoluminescence (CL) band at ≈ 2.9 eV, as well as an indication of the corresponding green band at ≈ 2.4 eV, have been equivalently doped by using extremely low dose B⁺- and C⁺-ion CIRA-implantations respectively. Comparative CL measurements showed changes in the intensities of the 2.9 and 2.4 eV bands and the generation of bands at ≈ 4 eV, as well as at ≈ 3.5 and ≈ 4.6 eV (the latter two in the B⁺-CIRA diamond). The results are commensurate with the model (proposed previously) in which the 2.9 and 4 eV bands are generated respectively by electron-hole recombinations at negatively charged acceptor- and positively charged donor-like, intrinsic defects. The present results indicate that Coulomb interactions between the latter defects and (at least partially) compensated, negatively charged, boron acceptors, generate the 3.5 and 4.6 eV bands, which may be considered as higher energy (≈ 0.6 eV) replicas of the 2.9 and 4 eV bands. In both cases, two electrons and a hole interact just before the hole combines with an electron. Such a configuration of charges seems related to, and could possibly be described as, a type of ”ionised exciton molecule”, where the ”bonding” of two negative ”nuclei” is facilitated by the presence of the hole. The CL measurements further indicate that the 2.4 eV band forms when a high enough density of, in this case, neutral acceptors are present. These neutral acceptors compete with the valence band to supply holes for recombination at the negatively charged, acceptor-type, intrinsic defects which are, in the absence of the boron, responsible for the generation of the blue, 2.9 eV band. Received: 5 December 1997 / Accepted: 13 December 1997