Thermal Evaluation of Scorched Graphite-Epoxy Panels by Infrared Scanning

A simple measurement system is described for evaluating damage to graphite-epoxy panels, such as those used in high-performance aircraft. The system uses a heating laser and infrared imaging system to measure thermal performance. Thermal conductivity or diffusivity is a sensitive indicator of damage in materials, allowing this thermal measurement to show various degrees of damage in graphite-epoxy composites. Our measurements track well with heat-flux damage to graphite epoxy panels. This measurement system, including analysis software, could easily be used in the field, such as on the deck of an aircraft carrier or at remote air strips.     

Electrical characterization of porous BaTiO3 using impedance spectroscopy in humid condition

The humidity response characteristics of La doped BaTiO₃ with different sintered densities and room temperature electrical conductivities were investigated using complex impedance measurement. The samples with low density and high resistivity showed the large and nearly linear sensitivity to the change of humidity. The impedance spectra of samples, when exposed to high humidity, can exhibit microstructure-related features, even though they do not give rise to a noticeable characteristic change when exposed to low humidity. The observed impedance patterns were dependent upon the density, and hence the oxidation kinetics of BaTiO₃.     

Evaluation of different coating systems by electrochemical methods

Corrosion protection of organic coated steel is determined by free corrosion potential measurements and impedance spectroscopy. The results are classified by means of very basic considerations and evaluation figures are developed. These electrochemical data are correlated with the extent of the corrosion for each coating system. The evaluation figures are used for ranking coating systems and this ranking is correlated with the ranking with reference to the results of standardized and exposure tests.     

High resolution XPS characterization of chemical functionalised MWCNTs and SWCNTs

High resolution XPS analysis of chemical functionalised multi-wall carbon nanotubes (MWCNTs) and single wall carbon nanotubes (SWCNT) was done with ESCA300 (overall instrument resolution of 0.35 eV). Information to the degree of functionalisation was ascertained by argon ion bombardment of the samples followed by XPS analysis to detect the functional groups, the percentage atomic concentration of various elements present and whether or not the detected functional groups imposed a chemical shift on the CNT atoms. The results show that true chemical functionalisation was achieved and by argon ion bombardment these functional groups can be altered relative to the C 1s carbon atoms of the CNT. The choice of chemicals used for functionalisation, the techniques employed and the types of nanotubes treated are important factors in chemical characterisation. The carbon atom on the nanotube ring to which the functional group (atom) is bonded, the chirality of the CNT, the electronegativity of the functional group, the bond type and whether the CNT is single-wall or multi-wall, or cut (short) could play a role in determining the chemical shift on the CNTs atoms. These investigations are relevant to chemical functionalisation of carbon nanotubes for various applications for example DNA sensors and other biomedical sensors.     

Softening and melting mechanisms of polyamides interfering with sliding stability under adhesive conditions

The thermal stability of polymers is a main issue when used as friction elements under dry sliding. Cast polyamide grades processed with either natrium or magnesium catalysors are slid on a small-scale and a large-scale test configuration to reveal the effect of softening or degradation on the sliding stability and to investigate possibilities for extrapolation of friction and wear rates between both testing scales. The combination of softening and afterwards transition into the glassy state is detrimental for the sliding stability of natrium catalysed polyamides, characterised by heavy noise during sliding. A transfer film formed under continuous softening also provides high friction. Melting during initial sliding is necessary for stabilisation in both friction and wear, and eventual softening of a molten film near the end of the test then not deteriorates the sliding stability. Softening of magnesium catalysed polyamides is favourable for the formation of a coherent transfer film resulting in more stable sliding than natrium catalysed polyamides. The differences in softening mechanisms of both polyamide grades is correlated to structural changes investigated by thermal analysis and Raman spectroscopy: the γ crystalline structure prevails in magnesium catalysed samples and the α crystalline structure is predominant in natrium catalysed samples. For internal oil lubricated polyamides, a time dependent degradation of the polyamide bulk deteriorates the supply of internal oil lubricant to the sliding interface, resulting in high friction and wear under overload conditions. As the degradation mechanisms during sliding are strongly correlated to the test set-up, extrapolation is only possible for friction in a limited application range, while wear rates cannot be extrapolated.     

Raman spectroscopic study of conformational changes in the amorphous phase of poly(lactic acid) during deformation

The conformational distribution change of amorphous poly(lactic acid) (PLA) induced by deformation has been studied using Raman spectroscopy. Spectroscopic features associated with the rotational isomeric states (ttt, ttg′, tg′t, tg′g′) have been established experimentally and supported by normal coordinate analysis. Deformation induced a significant increase in the most favorable tg′t conformation. Based on the relative intensities of Raman-active skeletal modes, a quantitative method has been developed that can be used to elucidate structural changes in a variety of deformed polymer samples. For biaxially oriented PLA films, the overall tg′t conformation increased from the 76% in undeformed sample to a value as high as 92%. The change in conformational distribution in the amorphous phase follows a different trend (76-88%) as compared to the increase in sample crystallinity (0-43%). A large change in amorphous chain conformation occurred at relatively low draw ratios. In contrast, the large change in the degree of crystallinity occurred at higher draw ratios.     

碱体系中系列羟基苯基卟啉红外光谱和拉曼光谱性质研究

本文继续深入研究该体系中相关物质的红外光谱和拉曼光谱的性质.论文结果说明,在碱体系中,NaOH只与羟基苯基卟啉周边meso-位的羟基反应形成盐,这个性质与紫外可见光谱性质是一致的.同时这一结果也为研究卟啉与金属的相互作用提供了有益的理论支持.     

Characterization of self-assembled monolayers of iron and cobalt octaalkylthiosubstituted phthalocyanines and their use in nitrite electrocatalytic oxidation

Cobalt and iron phenylthiosubstituted phthalocyanines have been deposited on Au electrode surfaces through the self-assembled monolayer (SAM) technique. The so formed layers were studied using voltammetric and impedance techniques. These SAMs blocked a number of Faradic processes and electrocatalyzed the oxidation of nitrite. The electrocatalytic parameters of the cobalt and iron phenylthiosubstituted phthalocyanines deposited on Au electrodes in nitrite solution were studied. Nitrite overpotentials which are lower than ever reported were obtained in this work for the iron phenylthiosubstituted phthalocyanines with very high stability.     

Impedance spectroscopy study of hardened Portland cement paste

In this paper, the differential impedance analysis (DIA) has been applied to the study of the dielectric properties of hardened Portland cement paste. Two time constants are found in the impedance spectra obtained in the frequency region form 100 kHz to 15 MHz. One time constant has been attributed to the solid matrix and the other one to the liquid phase filling the pores. The effect of the cement paste-electrodes interface has been quantified using two different experimental set-ups. Measurements using direct contact between electrodes and cement paste have been compared with measurements using an air gap technique in which the specimen “floats” between the electrodes. The two referred time constants have been found in both types of measurements. The influence of drying on the dielectric parameters is also studied.