车辆荷载作用下贝雷梁钢便桥动态响应数值仿真分析

以现代抢险救灾常用的贝雷梁钢便桥作为研究对象,采用ANSYS对其建立空间整体有限元模型,运用瞬态分析方法,模拟车辆过桥的整个过程,分析贝雷梁钢便桥的动态响应.结果表明:双排贝雷梁不均匀承担荷载,内侧贝雷梁相对较大,尤其在中轴和后轴荷载作用时,内外贝雷梁竖向位移差异最大;双排贝雷梁侧向位移几乎相同,且在中轴和后轴荷载作用时最大;主要以侧向和竖向振动为主,且不可忽略侧向振动响应,轴向振动响应较小可忽略不计.     

Metallographic sample prepared by ion beam etching

Ion beam etching technique was used to reveal the metallograhpic microstructure and interface morphology of electroplating chromium coating, in particular, whose substrate surface layer was treated in advance by laser quenching. Chemical etchings were also conducted for comparison. The reveal microstructures were observed and analyzed by scanning electron microscopy. The results show that ion beam etching can reveal well the whole microstructures of composite coating-substrate materials.     

串联法氧化铝生产中的合流脱硅

合流脱硅是简化联合法生产流程、降低能耗的有效措施。因此。国内外业界做了大量卓有成效的工作。串联法的工艺特点，更宜于采用合流脱硅。试验结果表明，串联法采用常压合流脱硅流程可以达到所需要的硅量指数。文中还对合流脱硅的硅量指数、合流点、合流脱硅温度、赤泥种子和添加石灰乳等问题进行了讨论。     

Theory and techniques of data mining in CGF behavior modeling

For the large quantity of data,rules and models generated in the course of computer generated forces (CGFs) behavior modeling,the common analytical methods are statistical methods based on the tactical rules,tactical doctrine and empirical knowledge.However,from the viewpoint of data mining,we can find many of these analytical methods are also each-and-every different data mining methods.In this paper,we survey the data mining theory and techniques that have appeared in the course of CGF behavior modeling f...     

使用动作脚本设计互动媒体

使用Flash制作动作,如果只基于时间轴和动画图层来设计,将会受到很大的限制,例如一些复杂、精彩的动画效果难以实现,也不能让观赏者与媒体互动,即媒体不具有交互性。要想动画具有交互性,能使观赏者通过选择来控制播放的顺序或呈现不同的内容,就需要使用Flash的动作脚本语言。     

抗噪Roberts算子边沿检测器

图像边缘检测是图像分割、目标识别、区域形态提取等图像分析技术的基础。边沿检测的软件实现有很多方法,但其一般无法保证在低成本计算平台上的实时性。因此文中基于形态学滤波和Roberts边沿检测算法提出一组数字电路,用以实现低成本、实时图像边沿检测器。文中还对比了Roberts算子的Matlab上实现和硬件实现的实际效果,发现实际硬件的边沿检测精度更高,噪声更多,必须采用去噪电路。该检测器消耗ALTERA-EP4CE115中2139个逻辑单元,每秒可处理30帧分辨率为640*480的RGB图像。     

Low-frequency wide-band hybrid energy harvester based on piezoelectric and triboelectric mechanism

Recently,hybrid energy harvester has been considered as an attractive potential approach to response the worldwide energy crisis due to the combination of advantages from different harvesting mechanism.In this paper,a novel low-frequency wide-band hybrid energy harvester based on piezoelectric and triboelectric mechanism is presented and systematically studied including structural design,fabrication process,working principle simulation and measurement.With a vibrational excitation,the polyvinylidene fluoride(PVDF) cantilevers will vibrate and impact the polydimethylsiloxane(PDMS) film on the substrate,producing a piezoelectric output as well as a triboelectric output.The structural parameters of each cantilever are optimized using finite element simulation,and the well-designed PVDF cantilevers with controllable PDMS mass not only reduce the device working frequency but also enlarge the bandwidth.Under a sweep-frequency test,three voltage peaks induced by the piezoelectric part are observed at 15,32.5 and 47.5 Hz,with the value of 320,288 and 264 mV,respectively.With the combined triboelectric part,a 20 V peak-peak voltage is generated at 15 Hz.The electrical driving ability of this hybrid energy harvester also has been demonstrated by lighting up a commercial light emitting diode(LED).     

受控振动柱体对波浪影响的数值模拟研究

以不可压缩黏性流体的Navier-Stokes方程为控制方程,采用RNG k-ε湍流模型,利用VOF方法追踪运动的自由表面的方法,建立了三维数值波浪与振动柱体相互作用的模型.基于经典绕射理论验证了波浪绕固定柱体传播的数值模型的可靠性,再采用动边界技术赋予柱体振动规律,研究受控振动柱体对波浪传播的影响,并通过控制柱体初始振动相位变化,系统地给出了在柱体振动的不同初始相位下柱体前后波浪变化的规律.     

曹妃甸新区水资源供需预测分析

依据曹妃甸新区国民经济规划资料,对其未来需水量进行了全面预测,并结合水资源配置规划方案,对各水平年的水资源供需进行了预测分析,以期为今后曹妃甸新区合理开发和有效利用水资源提供了科学依据。