Polyetherimide-LaNi5 composite films for hydrogen storage applications

This study investigates the preparation of polyetherimide (PEI) – LaNi₅ composites films for hydrogen storage. Prior to the polymer addition, LaNi₅ was ball-milled at different conditions (250, 350, and 450 RPM) and annealed at 500 °C for 1 h under vacuum. The composites were produced with BM-LaNi₅-350 (PEI/LaNi₅-350) and annealed BM-LaNi₅-350 (PEI/LaNi₅-350-TT). Membranes were successfully produced through solvent casting assisted by an ultrasonic bath. The particles dispersion and the film morphology did not change after hydrogenation cycles. In the H₂ sorption experiments at 43 °C and 20 bar, the films stored H₂ without incubation time; both samples reached a capacity of ~0.6 wt%. The H₂ sorption kinetics of PEI/LaNi₅-350 was comparable to that of BM-LaNi₅-350, whereas PEI/LaNi₅-350-TT presented significantly slower kinetics. LaNi₅ oxidation was hindered by PEI, showing that it can be explored to improve metal hydrides air resistance. The results demonstrated that PEI films filled with LaNi₅ are promising materials for hydrogen storage.     

Self-oscillating dimmable electronic ballast

This paper presents a simple alternative for an electronic ballast operating in self-sustained oscillating mode with dimming capability for fluorescent lamps. A simple modification in one of the gate drivers side circuit allows the lamp to dim without compromising the simplicity, reliability, and low cost which characterize the self-oscillating electronic ballast (SOEB). A qualitative analysis is presented to explain the behavior of the proposed self-oscillating electronic ballast with dimming feature. In addition, the stability and the key equations for the design are derived using the extended Nyquist criterion and describing function method. Experimental results from two 40-W electronic ballasts are presented to demonstrate the performance and to validate the analysis carried out.     

Preparation and characterization of chitosan‐based dispersions

Complexation of chitosan in aqueous solutions by low molecular weight electrolytes is one of the simplest methods for the preparation of aqueous chitosan dispersions. In this work, the influence of storage time, sulfate concentration, method of preparation and surfactant content on some properties of the resultant chitosan dispersions (turbidity, viscosity and zeta potential) was analyzed. Turbidimetry was adequate to monitor the formation of particles, while viscometry was suitable to monitor changes in the dispersing phase. An analysis of the properties of these systems, mainly in terms of particle–particle and macromolecule–macromolecule interactions was carried out. Copyright © 2004 Society of Chemical Industry     

The Ultrawideband Leaky Lens Antenna

A novel directive and nondispersive antenna is presented: the ultrawideband (UWB) leaky lens. It is based on the broad band Cherenkov radiation occurring at a slot printed between different infinite homogeneous dielectrics. The first part of the paper presents the antenna concept and the UWB design. The issues that are specifically addressed include the impedance matching, the radiation pattern and the phase purity. Subsequently the hardware demonstrator and the results of the measurement campaign are shown. The results fully validate the antenna concept. The antenna presents decade bandwidth impedance matching, directive and frequency independent patterns in the H-plane over two octaves, negligible cross-polarization levels, weak amplitude dispersivity and, according to the authors, the most stable phase center for a directive antenna over an ultra wide frequency range.     

Identification of thermoresistive solar radiation sensors

An identification procedure to estimate the parameters of a thermoresistive solar radiation sensor is presented. The proposed technique employs only electrical excitation for the sensor. The estimation algorithm is recursive and is applied to the sensor model derived from the thermodynamic equilibrium differential equations. The simulation and the experimental results demonstrate the validity of the proposed approach     

Dysprosium doped Ga:La:S glass for an efficient optical fibreamplifier operating at 1.3 μm

The authors present experimental results which indicate that a Dy ³⁺-doped Ga:La:S glass fibre amplifier may be operated efficiently at 1.3 μm with an optimum device length significantly shorter than a comparable Pr³⁺-doped glass fibre amplifier. Moreover, the efficiency exceeds that obtained from the Pr³⁺-doped ZBLAN devices currently available