Fabrication of lotus-type porous carbon steel by the continuous zone melting method and its mechanical properties

A lotus-type porous carbon steel with cylindrical pores was fabricated by the continuous zone melting method in a pressurized mixture of hydrogen and helium gases. The porosity increases with increasing partial pressure of the hydrogen gas, while the pore diameter remains almost constant, independent of the pressure. The ultimate tensile strength of the specimen with cylindrical pores parallel to the tensile direction is lower than the estimated value, assuming that the strength is decreased in proportion to the decrease of the cross-sectional area of the specimen, while the yield strength is higher than the estimated value. The compressive yield strength is also higher than the estimated value. The increase in yield strength is considered to be due to precipitation strengthening. The tensile strength is increased by quenching and tempering, while the elongation decreases. Such mechanical properties are discussed in terms of the microstructural analysis.     

Robust vector control of induction motors using full-order observer in consideration of core loss

This paper proposes a method for designing a robust full-order observer for vector-controlled induction motors taking core loss into account. Although conventional research focuses on parameter identification, global stability of the identification remains questionable. Therefore, robustness against some parameters is required. This paper describes the design of a robust full-order observer which takes core loss into account, using both the gain-scheduled H/sub /spl infin// control and the linear matrix inequality technique. This design always results in a stable controller. The robustness of the proposed method against variations of resistances is evaluated by experiments.     

Supermedia-enhanced Internet-based telerobotics

This paper introduces new planning and control methods for supermedia-enhanced real-time telerobotic operations via the Internet. Supermedia is the collection of video, audio, haptic information, temperature, and other sensory feedback. However, when the communication medium used, such as the Internet, introduces random communication time delay, several challenges and difficulties arise. Most importantly, random communication delay causes instability, loss of transparency, and desynchronization in real-time closed-loop telerobotic systems. Due to the complexity and diversity of such systems, the first challenge is to develop a general and efficient modeling and analysis tool. This paper proposes the use of Petri net modeling to capture the concurrency and complexity of Internet-based teleoperation. Combined with the event-based planning and control method, it also provides an efficient analysis and design tool to study the stability, transparency, and synchronization of such systems. In addition, the concepts of event transparency and event synchronization are introduced and analyzed. This modeling and control method has been applied to the design of several supermedia-enhanced Internet-based telerobotic systems, including the bilateral control of mobile robots and mobile manipulators. These systems have been experimentally implemented in three sites test bed consisting of robotic laboratories in the USA, Hong Kong, and Japan. The experimental results have verified the theoretical development and further demonstrated the stability, event transparency, and event synchronization of the systems.     

Efficiency of repeated batch penicillin fermentation using two fermentors. Computer simulation and optimisation

Repeated batch operation using two fermentors (RBTF) to penicillin fermentation was demonstrated by computer simulation to improve productivity. Three operation modes were compared: chemostat, repeated batch operation using a single fermentor (RBSF) and RBTF; in each case account was made of the lag period before growth. The simulated fermentor performances were assessed on the basis of the penicillin productivity and concentration; the simulation was based on published batch fermentation data. It was shown that RBTF was superior to RBSF and chemostat. The advantage of RBTF increased as the lag period became greater.     

Design for Consecutive Testability of System-on-a-Chip with Built-In Self Testable Cores

This paper introduces a new concept of testability called consecutive testability and proposes a design-for-testability method for making a given SoC consecutively testable based on integer linear programming problem. For a consecutively testable SoC, testing can be performed as follows. Test patterns of a core are propagated to the core inputs from test pattern sources (implemented either off-chip or on-chip) consecutively at the speed of system clock. Similarly the test responses are propagated to test response sinks (implemented either off-chip or on-chip) from the core outputs consecutively at the speed of system clock. The propagation of test patterns and responses is achieved by using interconnects and consecutive transparency properties of surrounding cores. All interconnects can be tested in a similar fashion. Therefore, it is possible to test not only logic faults but also timing faults that require consecutive application of test patterns at the speed of system clock since the consecutively testable SoC can achieve consecutive application of any test sequence at the speed of system clock.     

Preparation and antibacterial activity of novel fluoroalkyl end-capped oligomers/silica nanocomposites-encapsulated low molecular biocides

Fluoroalkyl end-capped N-(1,1-dimethyl-3-oxobutyl)acrylamide oligomer [R_F-(DOBAA) _n -R_F] reacted with tetraethoxysilane (TEOS) and silica nanoparticles in the presence of low-molecular weight biocides such as hibitane, hinokitiol, and hinokioil under alkaline conditions to afford R_F-(DOBAA) _n -R_F/silica nanocomposites-encapsulated these biocides in excellent to moderate isolated yields. Fluoroalkyl end-capped N,N-dimethylacrylamide oligomer [R_F-(DMAA) _n -R_F] and acrylic acid oligomer [R_F-(ACA) _n -R_F]/silica nanocomposites-encapsulated hibitane were obtained under similar conditions. Dynamic light scattering measurements showed that the size of these fluorinated nanocomposites-encapsulated biocides thus obtained is nanometer size-controlled. Additionally, these fluorinated nanocomposites were shown to have a good dispersibility and stability in methanol and water. Of particular interest, these fluorinated nanocomposites-encapsulated biocides were found to have a good antibacterial activity against Staphylococcus aureus, and these nanocomposites were applied to the surface modification of traditional organic polymers such as poly(methyl methacrylate).     

Crack opening displacement of a through-wall crack in a plate subjected to bending load

This study was performed in order to clarify crack opening displacement (COD) of through-wall cracks in a plate subjected to bending load. The former COD evaluation methods were mainly developed corresponding to tensile load, but there has been nothing that has been developed corresponding to bending load. Therefore, the authors evaluated CODs of the through-wall cracks in plates which were subjected to a bending load using finite element method (FEM) analyses, and proposed a simplified COD evaluation method accounting for both tensile and bending loads. The proposed method is useful for leakage evaluation at a crack opening of an elbow crown or in the vicinity of the coolant surface of a vessel in which the bending stress is relatively large.     

Differentiation of Arthroderma spp. by random amplification of polymorphic DNA (RAPD) and Southern hybridization

To develop the molecular differentiation analysis of dermatophytes, we carried out RAPD and Southern hybridization analyses using genomic DNAs of six Arthroderma species, including A. fulvum, A. grubyi, A. gypseum, A. incurvatum, A. otae and A. racemosum. The RAPD analysis gave different band patterns specific to each of the six Arthroderma fungi. However, minor differences in the banding patterns were observed between the strains of plus (+) and minus (-) mating types of A. gypseum, A. fulvum and A. incurvatum. Southern blot analysis using a probe (1S) obtained from A. grubyi DNA gave specific bands only in the DNA samples of A. grubyi and A. incurvatum. On the other hand, Southern blot analysis using a probe (C3) obtained from A. otae DNA gave specific bands in all six Arthroderma species examined, and the size of the bands were specific to each species. These findings indicate that RAPD and Southern hybridization analyses are useful in the differentiation of these Arthroderma species.     

Immunohistochemical demonstration of 3,2''-dimethyl-4-aminobiphenyl DNA adduct formation in various organs of Syrian golden hamsters

We attempted to purify endogenous growth factors of chick embryonal retinal pigment epithelial cells from bovine neural retina. Ammonium sulfate precipitation, gel filtration, and anion exchange column chromatography were used. Though only partially purification, bovine retinal extract had two effects, growth and transformation, on chick embryonal pigment epithelial cells. We think that these purified factors may be novel from the estimation of their molecular weight by gel filtration.