Preparation of a Near-Infrared Ray Absorption Film from N-Phenylthiocarbamoyl Chitosan Derivative

We recently observed that the decanoylation of N-phenylthiocarbamoyl chitosan (2) with a mixture of decanoic anhydride and pyridine at 60 °C for 24 h afforded N,N-(decanoyl)phenythiocarbamoyl-/2-isothiocynato chitosan decanoate (3b) rather than the expected product N,N-(decanoyl)phenylthiocarbamoyl chitosan decanoate (3a). This result suggested that some of the N,N-(decanoyl)phenylthiocarmbamoyl groups had been converted to isothiocyanate groups during the decanoylation process. The subsequent reaction of compound 3b with aniline gave N,N-(decanoyl)phenylthiocarbamoyl/N-phenylthiocarbamoyl chitosan decanoate (4) in high yield. A solution of compound 4 in CHCl₃ was then added to a solution of copper decanoate (5) in the same solvent, and the resulting mixture was cast onto a glass plate to give a cast film. The film was annealed at 200 °C in an oven to give a greenish film, which showed good near-infrared absorption characteristic in the range of 800–2200 nm.     

Detection of Multiple Blockages in Parallelized Microreactors

In a plant consisting of parallelized microreactors (MRs), the product quality is lowered because of a lack of flow uniformity among them when blockage occurs. It is not practical to install sensors in every MR from the viewpoint of cost when detecting the blocked MRs. In the previous study, the multiple blockage detection (MBD) method using a small number of sensors was proposed, but its performance became low when the number of sensors decreased. Here, the conventional algorithm for MBD is improved by considering the process behavior on blockage occurrence, and the effectiveness of the improved algorithm is demonstrated through a numerical case study. The effects of flow distributor types and sensor types on the MBD performance are numerically investigated.     

Vapor absorption by LiBr aqueous solution in vertical smooth tubes

Heat and mass transfer in a falling film vertical in-tube absorber was studied experimentally with LiBr aqueous solution. The presented results include the effect of solution flow rate, solution subcooling and cooling water temperature on the absorption in a smooth copper tube 16.05 mm I.D. and 400 mm long. The experimental data in the previous report for a 1200-mm-long tube was also re-examined and compared. It was demonstrated by the observation of the flow in the tube that the break down of the liquid film into rivulets leads to deterioration of heat and mass transfer at lower film Reynolds number or in longer tubes. An attempt to evaluate physically acceptable heat and mass transfer coefficients that are defined with estimated temperature and concentration at the vapor–liquid interface was also presented.     

Gap modulation in MCu[Q1−xQ′x]F (M=Ba, Sr; Q, Q′=S, Se, Te) and related materials

BaCuQF (Q=S, Se, Te) materials exhibit band gaps that allow transmission of much of the visible spectrum. BaCuSF is transparent in thin-film form with a band gap of 3.1 eV. Band gap estimates for powders of the solid solution series BaCuS_1−xSe_xF were obtained from wavelength-dependent diffuse-reflectance measurements using an integrating sphere. The band gap can be tuned by the substitution of Se for S to 2.9 eV for BaCuSeF. The decrease scales almost linearly with the increase in the volume of the tetragonal unit cell, which is determined primarily by the expansion of the a lattice parameter; the overall volume increase is 7.0% from x=0 to 1. Further reduction of the band gap is observed in BaCuSe_1−xTe_xF solid solutions, where a unit cell volume increase of 5.5% produces a band gap of 2.7 eV in BaCuSe_0.5Te_0.5F. Powders and films of BaCuSF exhibit strong red luminescence under ultraviolet excitation, which is suppressed by K doping. Additional tuning of band gap and electrical properties (the materials are p-type conductors) can be achieved by replacing Ba with Sr.     

Breakdown characteristics of oil and paper insulation for a very fast transient voltage

This paper describes the dielectric breakdown characteristics of oil and oil‐impregnated paper for very fast transient (VFT) voltages. Blumlein circuits generate VFT voltages of 60 and 300 ns in a pulse width that simulates disconnecting switching surges in gas‐insulated switch gears. We measured the breakdown voltages of needle‐to‐plane, plane‐to‐plane oil gaps and several pieces of paper between plane electrodes for VFT and lightning impulse voltages. The measured data were formulated in V‐t characteristics and Weibull probability distributions. The inclination n of V‐t characteristics of insulating paper is 150, which is less than n = 13.7 of the plane‐to‐plane oil gap in the VFT time range. The shape parameters of Weibull distribution obtained in this study show that the scattering of breakdown voltages of paper is much less than that of oil. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 141(4): 16–24, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10043     

Preparation and antibacterial activity of novel fluoroalkyl end-capped oligomers/silica nanocomposites-encapsulated low molecular biocides

Fluoroalkyl end-capped N-(1,1-dimethyl-3-oxobutyl)acrylamide oligomer [R_F-(DOBAA) _n -R_F] reacted with tetraethoxysilane (TEOS) and silica nanoparticles in the presence of low-molecular weight biocides such as hibitane, hinokitiol, and hinokioil under alkaline conditions to afford R_F-(DOBAA) _n -R_F/silica nanocomposites-encapsulated these biocides in excellent to moderate isolated yields. Fluoroalkyl end-capped N,N-dimethylacrylamide oligomer [R_F-(DMAA) _n -R_F] and acrylic acid oligomer [R_F-(ACA) _n -R_F]/silica nanocomposites-encapsulated hibitane were obtained under similar conditions. Dynamic light scattering measurements showed that the size of these fluorinated nanocomposites-encapsulated biocides thus obtained is nanometer size-controlled. Additionally, these fluorinated nanocomposites were shown to have a good dispersibility and stability in methanol and water. Of particular interest, these fluorinated nanocomposites-encapsulated biocides were found to have a good antibacterial activity against Staphylococcus aureus, and these nanocomposites were applied to the surface modification of traditional organic polymers such as poly(methyl methacrylate).     

Numerical analysis of two-dimensional steady-state and transient heat transfer in a parallel duct filled with pressurized He II

Analysis on steady-state and transient heat transfer on a flat plate at the middle of a parallel duct immersed in He II was performed for bath temperatures from 1.8 to 2.1 K at 101.3 kPa. Two-dimensional computer code named SUPER-2D developed by the authors based on the two-fluid model and the theory of mutual friction was used. Steady-state critical heat flux (CHF) and the time lag from the application of a step heat input to λ transition, that is called a lifetime, were obtained numerically for various step heat fluxes and for the channel gaps from 2 to 20 mm. Effect of the gap restriction on the CHF and the lifetime were clarified. The solutions were compared with the experimental data for the ducts with the same structures and the corresponding conditions. They agreed well with the experimental data. The heat transport mechanism in the parallel duct was clarified.