Improved atrial function in bicaval versus standard orthotopic techniques in cardiac transplantation

Atrial geometry is preserved in the bicaval technique of cardiac transplantation. Using Doppler echocardiography, we investigated the impact of this technique on preservation of atrial function and found that echocardiographic indexes of atrial function are improved in bicaval cardiac transplants versus the standard orthotopic transplants.     

Aortic valve papillary fibroelastoma. A diagnosis by transthoracic echocardiography

Cardiac papillary fibroelastomas are unusual, frond-like growths typically found on cardiac valves, diagnosed incidentally on autopsy or cardiac surgery, but rarely during life. We report a rare case of an aortic valve papillary fibroelastoma detected by transthoracic echocardiography and confirmed by histologic study.     

Radiation detector made of a high-quality polycrystalline diamond

Radiation detector was made of a high-quality CVD polycrystalline diamond composed of frost column like structure diamond grains, and induced charge distribution spectra and drift velocities were measured by using alpha particles. As a result, the CVD polycrystalline achieved maximum induced charge of 83% of HP/HT type IIa diamond. Moreover, the CVD crystal had lower charge loss on electrons compared with the HP/HT type IIa diamond. Drift velocities of electrons and holes were v_e = 7.7 × 10⁴ and v_h = 7.3 × 10⁴cm/s at an electric field of 20 kV/cm, respectively. In addition, response function measurement for 14 MeV neutrons was carried out.     

A feasibility study of a direct-mapping parallel processing method to solve linear equations in load-flow calculation

With the growing size and complexity of power systems, system analysis—such as transients calculation—takes much time. Hence, fast calculation methods are required. Although parallel processing is a hopeful method, there have been difficulties in the parallel solution of linear equations which appear in power-flow calculations by the Newton-Raphson method. This paper aims at the fast calculation of the power-flow problem by means of parallel processing. In order to improve the suitability to the parallel solution of the differential equation in transients calculation, we assume the use of a direct-mapping parallel processing machine to map directly the network of a power system onto a network of processors. Under this assumption, we propose a new parallel-processing-oriented method in which the linear equation is solved by linear iterations between nodes with Aitken acceleration. We simulate the method on three model power systems and compare this Parallel Iterative Method (PIN) with a Parallel Direct Method (PDM) which uses the banded matrix according to the number of operations required. As a result, we can expect that PIM may solve linear equations faster than PDM with m processors, although the PIM might be inferior to the PDM with m × m processors, where m denotes the half-band width of the banded matrix.     

3-D face recognition method based on optimum 3-D image measurement technology

Most face recognition systems employ 2-D color or gray-scale images. However, face recognition based on 2-D images is adversely affected by 3-D movement, variable lighting, and the use of cosmetics. 3-D image measurement technology has the potential to overcome these limitations of face recognition based on 2-D images since it can perform geometric analysis. We propose a method that is capable of recognizing a person from a 3-D facial image obtained using a 3-D shape measurement system by employing a technique that optimizes the intensity-modulation pattern projection. This face recognition method is based on the iterative closest point algorithm. It is robust to changes in reflectivity and color. Since the 3-D facial information can be registered, this method can estimate rotations and translations to compensate for different positions or directions. In order to prove the validity of the proposed technique, a verification experiment was conducted which used 105 sample 3-D images obtained from 15 subjects. It achieved a detection rate of 96% when heads were turned at an angle of 20° or less relative to the camera.     

Application of the solid polymer electrolyte (SPE) method to organic electrochemistry—III. Kolbe type reactions on Pt-SPE

The feasibility of a solid polymer electrolyte (SPE) method for Kolbe type reactions was investigated by using Pt-SPE composed with Nafion 415 and platinum. The Kolbe reaction of acetic acid proceeded effectively on one side and both sides Pt-SPE composites. The lower current efficiency was observed on the latter than on the former. Neat acetic acid could also be electrolysed on both sides SPE though the cell voltage was fairly high.A methanolic solution of monomethyl adipate was electrolysed to give dimethyl sebacate on both sides Pt-SPE according to the Brown-Walker reaction. The current efficiency and the terminal voltage increased with the concentration of monomethyl adipate. Pt-SPE behaved as an active electrode of a high roughness factor, eg about 6, for the Kolbe reaction of acetate.     

Investigation of the effect of surface phosphate ester dispersant on viscosity by coarse-grain modeling of BaTiO slurry

To understand the role of phosphate ester dispersant, we investigated the rheology of a BaTiO slurry. For the model case, a coarse-grain molecular dynamics (CGMD) simulation was performed with the butyral polymer didodecyl hydrogen phosphate (DHP) in the toluene/ethanol solvent. By systematically analyzing the effect of DHP from an atomic-scale first principle and from all-atom MD to microscale CGMD simulation, we investigated how the adsorption of a DHP dispersant on a BaTiO surface affects the microstructure rheology of a BaTiO slurry. The first-principle and all-atom MD simulation suggests that DHP molecules prefer to locate near the BaTiO surface. CGMD simulation shows a reduction in viscosity with an increase in dispersants, suggesting that the dispersant population near the BaTiO surface plays a key role in controlling the rheology of the BaTiO slurry. In this study, we propose an approach for understanding the BaTiO slurry with molecular-level simulations, which would be a useful tool for efficient optimization of slurry preparation.     

Observation of single-walled carbon nanotubes by photoemission microscopy

Single-walled carbon nanotube networks grown on SiO₂ pillars were studied by means of scanning photoemission microscopy. The individual nanotubes or nanotube bundles growing from the pillar tops were observed in C 1s images. Band bending near catalytic Fe/nanotube contacts in an end-bonded configuration was studied by measuring C 1s spectra along the tube axes. Within our experimental resolution, no band bending was observed. This implies that the depletion width is less than the spatial resolution of the scanning photoemission microscope (90 nm) or that the amount of the band bending is less than 0.1 eV.     

Preparation and characterization of electroplated amorphous gold-nickel alloy film for electrical contact applications

A process for electroplating amorphous gold-nickel alloy with the atomic ratio of unity was developed. The plating bath was prepared by adding potassium cyanoaurate(I) into a known plating bath which produces amorphous nickel-tungsten alloy. At a sufficiently high gold concentration, the alloy deposit did not contain any tungsten. The amorphous nature of the Au-Ni alloy produced in the new bath was confirmed by using TEM and THEED. Hardness, resistivity, and contact resistance of this new alloy were determined, and the results are discussed for applications as an electrical contact material.