ABSTRACTThe thermal characterization of aluminum flat grooved heat pipes is performed experimentally for different groove dimensions. Three heat pipes with groove widths of 0.2?mm, 0.4?mm, and 1.5?mm are used in the experiments. The effect of the amount of the working fluid is extensively studied for each groove width. The results reveal that, although all three succeed in dissipating the heat input through the phase change of the working fluid by continuous evaporation and condensation, the effectiveness of the heat transfer increases with reduced groove width. Furthermore, it is observed that there exists an optimum operating point, where the temperature difference between the heating and cooling sections is at a minimum, and the magnitude of this temperature difference is a strong function of the groove width. To the best of the authors’ knowledge, the combined effects of groove dimensions and the amount of the working fluid, from fully flooded to dry, is reported for the first time for aluminum flat grooved heat pipes. 相似文献
In this paper, a new design procedure for LLC converter has been introduced. In fact, this method is a computer-based design algorithm based on a numerical technique. In the process of designing, the value of the resonant element is obtained by solving the LLC converter fundamental equation. This converter will be controlled by using state feedback, such as output voltage variable. As a matter of fact, in a control system, the change of output voltage (because of load variation) will affect the switching frequency, so the output voltage will be tuned. In the designing process, the fundamental equations of LLC converter are obtained, and the value of the resonant elements is calculated. Also, a comparison analysis is carried out between the proposed and typical methods. The simulation is done to investigate the validity of the proposed method. Moreover, a prototype is manufactured, and the experimental test is done to evaluate its applicability. 相似文献
Weekly storage of coolness in heavy walls (walls with large thermal inertia or large characteristic time constants or low Fourier numbers) was investigated numerically by considering one-dimensional heat conduction through the walls. The study consisted of first analyzing the heat flow through a single wall and considering various boundary conditions on the inside. The boundary conditions were: constant inside air tempeture throughout the day, variable inside air temperature on a 24-hour cycle, and variable inside air temperature on a 48-hour cycle. Next, the heat flow through walls was studied through a thermal network analysis of a simple building. In this case it was assumed that the ambient air temperature (following a periodic distribution) was increased suddenly and followed this new distribution for many days thereafter.It was concluded that walls with high thermal inertia or time constant can store coolness for several days. The larger the time constant of the wall (for example adobe as compared with brick) the longer it takes for the wall temperature to reach a steady periodic distribution after the change has occurred. However, because of low thermal conductivity of adobe, the retrieval of the stored coolness in these walls is slow, and the mean daily temperature of the room air in the adobe building does not change appreciably beyond seven days after the change. Increase of the wall thickness beyond 50 cm does not improve the thermal performance of the building significantly. 相似文献
A new method for prediction of Gurney velocity of explosives is introduced in which energy output is correlated with the heat of detonation, the number of moles of gaseous products of detonation per gram of explosive and the average molecular weight of gaseous products. It is assumed that the CHNO explosive reacts to form products composed of N2 , CO, H2O, CO2, H2,O2 and C(s) as determined by the oxygen balance of the unreacted compound. Good agreement is obtained between measured and calculated values of Gurney velocity as compared to previous correlations which assumed the reaction products to consist of N2 , H2O, CO2 and either C(s) or O2. 相似文献
The present work aimed to evaluate and optimize the design of an artificial neural network (ANN) combined with an optimization algorithm of genetic algorithm (GA) for the calculation of slope stability safety factors (SF) in a pure cohesive slope. To make datasets of training and testing for the developed predictive models, 630 finite element limit equilibrium (FELE) analyses were performed. Similar to many artificial intelligence-based solutions, the database was involved in 189 testing datasets (e.g., 30% of the entire database) and 441 training datasets; for example, a range of 70% of the total database. Moreover, variables of multilayer perceptron (MLP) algorithm (for example, number of nodes in any hidden layer) and the algorithm of GA like population size was optimized by utilizing a series of trial and error process. The parameters in input, which were used in the analysis, consist of slope angle (β), setback distance ratio (b/B), applied stresses on the slope (Fy) and undrained shear strength of the cohesive soil (Cu) where the output was taken SF. The obtained network outputs for both datasets from MLP and GA-MLP models are evaluated according to many statistical indices. A total of 72 MLP trial and error (e.g., parameter study) the optimal architecture of 4 × 8 × 1 were determined for the MLP structure. Both proposed techniques result in a proper performance; however, according to the statistical indices, the GA–MLP model can somewhat accomplish the least mean square error (MSE) when compared to MLP. In an optimized GA–MLP network, coefficient of determination (R2) and root mean square error (RMSE) values of (0.975, and 0.097) and (0.969, and 0.107) were found, respectively, to both of the normalized training and testing datasets.
Catalysis Letters - Several highly efficient and magnetically recyclable cobalt catalytic systems were prepared using magnetic chitosan and some safe and available organic compounds... 相似文献
Silicon - In this paper, a new structure: triple work function metal gate SOI MESFET, intended for integration into the deep-submicron CMOS technology, is proposed. The gate of the device consists... 相似文献