Theoretical estimation of dielectric loss of oxide glasses using nonequilibrium molecular dynamics simulations

To theoretically explore amorphous materials with a sufficiently low dielectric loss, which are essential for next-generation communication devices, the applicability of a nonequilibrium molecular dynamics simulation employing an external alternating electric field was examined using alkaline silicate glass models. In this method, the dielectric loss is directly evaluated as the phase shift of the dipole moment from the applied electric field. This method enabled us to evaluate the dielectric loss in a wide frequency range from 1 GHz to 10 THz. It was observed that the dielectric loss reaches its maximum at a few THz. The simulation method was found to qualitatively reproduce the effects of alkaline content and alkaline type on the dielectric loss. Furthermore, it reasonably reproduced the effect of mixed alkalines on the dielectric loss, which was observed in our experiments on sodium and/or potassium silicate glasses. Alkaline mixing was thus found to reduce the dielectric loss.     

Direct observation of the crystal-growth transition in undercooled silicon

Using an electromagnetic levitation facility with a laser heating unit, silicon droplets were highly undercooled in the containerless state. The crystal morphologies on the surface of the undercooled droplets during the solidification process and after solidification were recorded live by using a high-speed camera and were observed by scanning electron microscopy. The growth behavior of silicon was found to vary not only with the nucleation undercooling, but also with the time after nucleation. In the earlier stage of solidification, the silicon grew in lateral, intermediary, and continuous modes at low, medium, and high undercoolings, respectively. In the later stage of solidification, the growth of highly undercooled silicon can transform to the lateral mode from the nonlateral one. The transition time of the sample with 320 K of undercooling was about 535 ms after recalescence, which was much later than the time where recalescence was completed.     

Containerless solidification of highly undercooled mullite melts: Crystal growth behavior and microstructure formation

A mullite (3Al₂O₃·2SiO₂) sample has been levitated and undercooled in an aero-acoustic levitator, so as to investigate the solidification behavior in a containerless condition. Crystal-growth velocities are measured as a function of melt undercoolings, which increase slowly with melt undercoolings up to 380 K and then increase quickly when undercoolings exceed 400 K. In order to elucidate the crystal growth and solidification behavior, the relationship of melt viscosities as a function of melt undercoolings is established on the basis of the fact that molten mullite melts are fragile, from which the atomic diffusivity is calculated via the Einstein-Stokes equation. The interface kinetics is analyzed when considering atomic diffusivities. The crystal-growth velocity vs melt undercooling is calculated based on the classical rate theory. Interestingly, two different microstructures are observed; one exhibits a straight, faceted rod without any branching with melt undercoolings up to 400 K, and the other is a feathery faceted dendrite when undercoolings exceed 400 K. The formation of these morphologies is discussed, taking into account the contributions of constitutional and kinetic undercoolings at different bulk undercoolings.     

Hardware system of the Earth Simulator

The Earth Simulator (ES), developed under the Japanese government’s initiative “Earth Simulator project”, is a highly parallel vector supercomputer system. In this paper, an overview of ES, its architectural features, hardware technology and the result of performance evaluation are described.

In May 2002, the ES was acknowledged to be the most powerful computer in the world: 35.86 teraflop/s for the LINPACK HPC benchmark and 26.58 teraflop/s for an atmospheric general circulation code (AFES). Such a remarkable performance may be attributed to the following three architectural features; vector processor, shared-memory and high-bandwidth non-blocking interconnection crossbar network.

The ES consists of 640 processor nodes (PN) and an interconnection network (IN), which are housed in 320 PN cabinets and 65 IN cabinets. The ES is installed in a specially designed building, 65 m long, 50 m wide and 17 m high. In order to accomplish this advanced system, many kinds of hardware technologies have been developed, such as a high-density and high-frequency LSI, a high-frequency signal transmission, a high-density packaging, and a high-efficiency cooling and power supply system with low noise so as to reduce whole volume of the ES and total power consumption.

For highly parallel processing, a special synchronization means connecting all nodes, Global Barrier Counter (GBC), has been introduced.     

Critical heat flux on a flat plate heater located at the middle of a duct in forced flow of pressurized He II

Critical heat fluxes (CHFs) were measured for two types of rectangular ducts containing horizontal flat plate heaters. One has the flat plate heater of 6 mm wide and 20 mm long located on the inner lower wall at 50 mm from the inlet. The other duct has two horizontal flat plates of 6 mm wide and 20 mm long on inner upper and lower walls at 50 mm from the inlet. The equation of CHF for the forced convection containing a new nondimensional-parameter m introduced in order to calculate cross-sectionally averaged liquid temperature at the center of the duct was derived based on two fluid model, ordinary convection theorem and experimental results. It was confirmed that this correlation can describe not only the author's data on the duct but also other worker's data for channels with different shapes and sizes.     

Rapid detection cytomegalovirus pneumonia in recipients of bone marrow transplant: evaluation and comparison of five survey methods for bronchoalveolar lavage fluid

To detect cytomegalovirus-associated interstitial pneumonia (CMV-IP) in recipients of BMT in its earliest stage, five CMV methods were assessed for their usefulness using bronchoalveolar lavage fluid as the test specimen. Of the 43 cases enrolled in the study, PCR was positive in 12 cases, shell vial in eight, culture in eight and cytology in three. There were no positive cases in in situ hybridization. Based on this result, the 43 cases were classified into four groups: Group 1, three cases: positive in PCR, shell vial and cytology; Group 2, five cases: positive in PCR and shell vial; Group 3, four cases: positive only in PCR; and Group 4, 31 cases: negative in all CMV tests. Cases in Group 1 were judged as having the highest risk of overt CMV-IP. They were successfully treated with a combination of ganciclovir and immunoglobulin. Group 2 was diagnosed as having active CMV infection and ganciclovir monotherapy was effective for these patients. Groups 3 and 4 were not given anti-CMV therapy, but they were free from CMV-related manifestations throughout the study. The sensitivity and specificity of each survey method for the detection of Groups 1 and 2 were 1.0 and 0.89 in PCR, 1.0 and 1.0 in shell vial, 0.88 and 1.0 in culture, and 0.38 and 1.0 in cytology. Similarly, the positive and negative predictive values were 0.67 and 1.0 in PCR, 1.0 and 1.0 in shell vial, 1.0 and 0.97 in culture, and 1.0 and 0.88 in cytology. Thus, CMV survey on bronchoalveolar fluid was thought to be useful in detecting post BMT CMV-IP in its earliest stage.     

Tunable laser for sensing atmospheric transmission in the infrared region of 11 ∼ 16 µm

We succeeded in observing the continuously tunable, pulsed InSb SFR (Spin-Flip Raman) laser emission in the infrared region of 11～16µm (11.4～16.3µm) from only one InSb device, merely by adjusting the pumping wavelength (11 lines from the infrared NH₃ laser) and the applied magnetic field (0～80 kGauss).     

Air vent in water chamber and surface coating on liner slides concerning auxiliary cooling system for the high temperature engineering test reactor

Experimental study was made to confirm the validity of new designs of the auxiliary cooling system for the high temperature engineering test reactor (HTTR). First, it is necessary to vent residence air in outlet side of water chamber of the auxiliary heat exchanger for the HTTR. Accordingly, we have proposed to mount a proper bend duct in the outlet side of the water chamber. Air vent is done by difference between pressures at both ends of the bend duct caused by the forced water circulation using the water pumps. From flow tests, it was confirmed that it is capable of venting the air through the bend duct by circulating the water in maximum capacity of the water pumps. Second, it is essential to prevent seizure and excessive wear of the liner slides of the auxiliary concentric hot gas duct for the HTTR at a service temperature of 950°C. Therefore, we have put forward to coat titanium nitride (TiN) on the surface of the liner slides made of nickel-based superalloy Hastelloy XR using the thermochemical vapor deposition method. As a result of seizure and wear tests, it was confirmed that the TiN coating film of 3 μm on the surface of Hastelloy XR is sufficient.     

Permeation of Zidovudine and Probenecid from Oily Bases Containing Alcohols Through Rat Skin

Permeation of zidovudine (3'-azido-3'-deoxythymidine, AZT) and probenecid from oily bases containing an alcohol through rat skin was examined. Isopropyl myristate (IPM), as an oily vehicle, showed a penetration enhancing effect for AZT and probenecid. Ethanol, n-propanol, and n-butanol were used as additives in IPM and were examined for their own permeation and the enhancing effect on the permeation of AZT and probenecid. The skin permeation of AZT and probenecid from IPM was enhanced by addition of the alcohol in IPM. The degree of the enhancement was decreased with increasing lipophilicity of the alcohol used. me permeation rate of the drug from those systems was shown to be governed by penetration-enhancing effects of the oily base and alcohol, and the penetration of the alcohol itself through the skin.