A sensorless brushless dc motor system

This paper describes a brushless dc motor system without position or speed sensor. The brushless motor consists of a permanent magnet synchronous motor and a voltage-source inverter capable of controlling the amplitude and frequency of voltage. The rectangular-shaped stator current with a conducting interval of 120° (electrical) is controlled to be in phase with the trapezoidal back electromotive force. This results in producing maximum torque. Variable speed is achieved by adjusting the average motor voltage similarly to chopper control of dc motors. In this paper, two sensorless position detecting methods, i.e., an “indirect method” suited for the lower-speed range and a “direct method” suited for the higher-speed range are proposed. The combination of the two makes it possible to detect the rotor position over a wide-speed range. Furthermore, a speed-sen-sorless PLL control is proposed in applying the principle of the direct method. Experimental results obtained from a prototype brushless dc motor are shown to confirm the validity of the sensorless drive. The starting procedure of the motor also is discussed because it is impossible to detect the rotor position at a standstill.     

Longitudinal elastic waves in columns due to earthquake motion

An analysis is presented of longitudinal waves in a thin elastic column. Velocity is specified at one end, and the boundary condition at the other end is expressed in terms of a range of effective impedances of an attached structure. Propagation, reflection and interference of the waves are followed by the method of characteristics. Integration of differential equations along characteristics yields the wave-induced stress, which is then applied to problems of earthquake excitation. Numerical examples are given for recorded updown ground motion of the Kobe Earthquake.     

Development of 170 GHz/500 kW gyrotron

A development of 170GHz/500kW level gyrotron was carried out as R&D work of ITER. The oscillation mode is TE_31,8. In a short pulse experiment, the maximum power of 750kW was achieved at 85kV/40A. The efficiency was 22%. In the depressed collector operation, 500kW/36%/50ms was obtained. The maximum efficiency of 40% was obtained at P_RF=470kW whereas the power decrease by the electron trapping was observed. Pulse extension was done up to 10s at P_RF=170kW with the depressed collector operation. The power was limited by the temperature increase of the output window.     

STRUCTURE FORMATION OF COATED FILMS WITH DISPERSED PIGMENTS DURING DRYING

In the drying of coated films with dispersed pigments, such as floppy disks, the structure of the film is formed during the drying process and depends on the drying condition. It is important to understand the structure formation during drying for the design of the dryer and die better quality of the product. We measured die drying characteristics of the film and determined the structure of dried film experimentally. A qualitative model for the structure formation during drying of the coated film is suggested.     

Characteristics and classification of high-current fault arcs on distribution systems

When a fault occurs on transmission or distribution systems due to lightning or overvoltage, often an arc discharge occurs at the fault point. The arc discharge, which is caused by a fault current, has a high current, high temperature, strong light emission, etc., thus it sometimes causes heavy damages to electric power equipment. The arc discharge is influenced by the conditions around the arcs, i.e., gas, insulation materials, gap length, weather, etc. Also, the arc voltage along the arc column indicates the characteristics of the arc. If the voltage waveforms of the arcs caused by the fault on transmission or distribution systems are classified, it is possible to find the location and the equipment where the fault occurred. In this paper, the arc voltage data in 6-kV class XLPE cables and 6-kV class overhead lines are analyzed and an artificial neural network method is applied to classify the arc voltage waveforms. The results obtained from the six artificial neural networks developed show that the artificial neural network method is effective for classification of arc voltage waveforms if adequate input parameters are selected.     

Predicted and observed initial short circuit current for lead-acid batteries

Initial short circuit currents have been observed using our electronic short circuit switch and also predicted from terminal voltage and ohmic resistance according to Ohm's law for several kinds of lead-acid batteries in various states-of-charge. Ohmic resistance was measured by the d.c. step and the a.c. impedance methods. The predicted and the observed values have been compared in order to establish a prediction method for initial short circuit current. A good agreement was obtained, the root mean square percentage deviation of the predicted value from that observed being only 219%, which confirms the validity of the prediction method for the initial short circuit current.     

ARCOR,a new photolithography technique with antireflective coating on resist

The multiple interference effect is one of the major causes of the fluctuation in critical dimension control (CD) and in mark detection for alignment. Suppressing this effect is critical for future photolithography. We propose a new photolithography technique called anti reflective coating on resist (ARCOR), which improves linewidth accuracy and overlay accuracy by suppressing multiple interference. ARCOR consists of relatively simple processes: A clear antireflective film is spun onto the resist prior to the mark detecting for alignment and exposure. The film is subsequently removed and the resist developed in the conventional way. ARCOR differs from ARC, which suppresses the reflection at the resist/substrate interface. ARCOR suppresses the reflection at the air/resist interface. ARCOR allows mark detection and exposure without light intensity-loss and multiple interference. The experiments mainly examine polysiloxane and perfluoroalkylpolyether as ARCOR materials. It is shown that linewidth accuracy can be improved from 0.3 to 0.03 μm. The signal-to-noise ratio of the alignment signal is drastically improved, and the overlay error is about half that of the conventional method. ARCOR is also effective for directly measuring the reflectivity at the resist/substrate interface, which is a key parameter of the multiple interference effect and the halation. Using ARCOR and a thin resist film, the measured ratio of reflected light to incident light indicates the reflectivity at the resist/substrate interface. Because, the probe light does not reflect off the resist surface and the intensity-loss at the resist surface is suppressed. With perfluoroalkylpolyether film, the measurement error is ～ 1.5%.     

Quantitative structural analysis of twin boundary in alpha-Zn7Sb2O12 using HAADF STEM method

The structure and composition of the 1/4{110} twin boundary in alpha-Zn7Sb2O12 have been determined by using quantitative high-angle annular dark field scanning transmission electron microscopy (HAADF STEM) analysis. The noise in the experimental HAADF STEM images is reduced by using the maximum entropy method and average processing, and the parameters used in dynamical simulations are experimentally determined. From the analysis, it has been found that octahedral sites in the twin boundary slightly shift parallel to the [110] direction, and a reduction of the Sb concentration at the octahedral sites on the plane adjacent to the twin boundary was detected. The reduction was measured from three regions in the same twin boundary, and the Sb concentrations were 4 +/- 3, 8 +/- 3 and 19 +/-2 at% from 33 at%.