Fundamental Evaluation of Power Supply and Rectifiers for Wireless Power Transfer Using Magnetic Resonant Coupling

This paper provides a fundamental analysis of a power supply and rectifiers for wireless power transfer using magnetic resonant coupling (MRC). MRC enables efficient wireless power transfer over middle‐range transfer distances. MRC for wireless power transfer should operate at a high frequency in the industry science medical band, such as 13.56 MHz, because the size of the transfer device decreases at higher transfer frequencies. Therefore, the output frequency of the power supply on the transmitting side should be 13.56 MHz. In addition, the rectifier on the receiving side is operated at a high frequency. This paper focuses on the reflected power in the power supply and rectifiers. Thus, the parametric design method is clarified for the power supply, including a low‐pass filter to match the output, the impedance of the power supply with the characteristic impedance of the transmission line. In addition, the effects on the rectifiers of silicon carbide and gallium nitride diodes are confirmed by performing an experiment and a loss analysis.     

Studies on chitin. IX. Crosslinking of water-soluble chitin and evaluation of the products as adsorbents for cupric ion

Water-soluble chitin was successfully crosslinked to varying extents with glutaraldehyde in homogeneous aqueous solutions to improve the properties as an adsorbent for metal cations, and the effects of crosslinking were discussed. Complete insolubilization was achieved with the fivefold excess aldehyde, but, in terms of adsorptivity of Cu²⁺, the chitin crosslinked at an aldehyde/amino group ratio of 1.0 was found to exhibit remarkable capacity and was much superior to others. The desorption of Cu²⁺ from the adsorption complex was also attained effectively at pH 2.0. These results indicated that the loose crosslinking was quite simple and efficient to produce high capacity adsorbents for practical use. Thermal behavior of the crosslinked chitin was examined by TMA and TGA; a softening phenomenon was observed at 145°C.     

Characterization of a cartilage-derived 66-kDa protein (RGD-CAP/beta ig-h3) that binds to collagen

Malignant human gliomas are the most common forms of primary tumors in the central nerve system. Due to their location and invasive nature, treatment so far has been mainly palliative. Thus, understanding the molecular detail of tumor transformation and progression is crucial for developing effective therapeutic strategy for this fetal tumor. Among the genetic alternations found in these tumors, p53 inactivation and PDGF/PDGFR activation represent the early events, and the loss of chromosome 10 and gene amplification and rearrangement of EGFR represent the late events. Studies with both glioma cell lines and primary tumor tissues have strongly suggested that TGF-alpha and EGFR function as an important autocrine loop in supporting proliferation of human glioma, especially in high grade glioma, since elevated TGF-alpha expression is also found in these high grade tumors. Furthermore, down regulation of the expression of TGF-alpha by antisense constructs has been shown to inhibit several types of human tumor cell growth including glioma. Other means of therapeutic approaches using this autocrine loop as a target also include the use of monoclonal antibodies and their cytotoxic conjugated. Considerable understanding of the EGFR-mediated signal transduction pathways has become available recently, which including GRB2/mSOS1 mediated MAP kinase activation; JAK/STATs pathway; PLC-gamma pathway. However, much work still needs to be done before a specific component of these pathways can be applied for effective control of tumor growth in the clinic.     

Oxygenation in the rabbit myocardium: assessment with susceptibility-dependent MR imaging

PURPOSE: To determine the feasibility of using hemoglobin (Hb) desaturation as an indicator of myocardial oxygenation. MATERIALS AND METHODS: High-resolution gradient-echo nuclear magnetic resonance (MR) images of isolated, blood-perfused rabbit hearts were obtained at various blood oxygenation levels. The hearts were perfused at 37 degrees C with a Langendorff apparatus modified for nuclear MR imaging. The perfusate contained bovine red blood cells in a cardioplegic solution that eliminated motion artifacts and minimized arteriovenous oxygenation differences. Hb saturation was varied (7%-100%) randomly. Perfusion pressure was continuously monitored, and blood samples were obtained. RESULTS: There was a substantial correlation between image signal intensity in the myocardium and Hb saturation in the blood, believed to be due to susceptibility effects of the paramagnetic species deoxyhemoglobin. CONCLUSION: Direct and noninvasive determination of regional Hb saturation with susceptibility-dependent MR imaging may provide information regarding regional myocardial O2 content.     

Mechanical alloying in the Al-Bi alloy system

Mechanical alloying (MA) was carried out to investigate the MA behaviour of the immiscible Al-10, 30 at % Bi alloys. After the MA processing, the Al and Bi were finely and homogeneously alloyed. The Bi crystallite size decreased to 25 nm and 30 nm in the Al-10 at % Bi and Al-30 at % Bi alloys, respectively. By increasing the MA time, the hardness increased up to a value of 80 H _v, which is larger than that obtained from the rule of mixtures. The lattice parameter of Bi decreased by about 0.27%, which shows the formation of a non-equilibrium hcp Bi super-saturated solid solution. The extended solubility of Al in Bi was 1.9% in the Al-30 at % Bi alloy. Due to the extended solubility, depression of the melting temperature of hcp Bi was confirmed in the mechanically alloyed Al-Bi alloys. The maximum depression in the temperature was about 10 K. The measured values corresponded well with those estimated from the extrapolation of the solidus line.     

Recovery retardation in equal channel angular pressed Al–Zr alloy during friction stir welding

The effect of Zr on reduction of hardness and microstructure in an FS weld of equal channel angular-pressed Al alloy was investigated. Zr addition to Al suppressed dynamic recovery in the thermomechanically affected zone and enabled retention of the high hardness of the ECA-pressed material throughout the weld.     

A load dispatch method using fractional programming and semidefinite programming

This paper describes a load dispatch method which minimizes power cost—[fuel cost]/[electric output]—for a power system with thermal plants and energy storage facilities. The proposed method employs fractional programming to convert a minimization problem with fractional objective function to a series of quadratic minimization problems, and semidefinite programming to solve converted problems. The method provides the optimum time‐dependent power output/input and storage level of energy storage facilities as well as time‐dependent power output of thermal plants. The method has been applied to a power system with five thermal plants, two energy storage facilities of various performances, and five load demands. The optimum load scheme of four time mesh points is obtained for the thermal plants and energy storage facilities. The fractional programming successfully converges the optimal scheme through a few iterations. The semidefinite programming deals with a variable matrix of 164 dimensions, and 185 inequality constraints. © 2001 Scripta Technica, Electr Eng Jpn, 138(2): 49–58, 2002     

Surface Hardening of Carbon Steel Using High Powered YAG Laser

A high powered YAG laser with kaleidoscope for surface modification was applied to the surface hardening of carbon steels containing 0. 18-0.54 wt% C without the absorbents, and the relationships between laser processing and surface hardening were investigated by hardness and microstructure. The structure of the hardened zone underwent complete martensitic transformation in all of the carbon steels tested, and its hardness increased with greater carbon content. Under identical irradiated conditions, the hardened zone expanded with increasing carbon content. A hardened zone extending from the surface to a depth of 1.0 mm was obtained at a laser power of 1.0 kW and a scanning speed of 1 mm/sec. It was found that in the surface hardening of carbon steels, a high powered YAG laser can be used to control the hardened zone by selecting the appropriate irradiation conditions, however, the hardened zone was affected by the assistant gas and the flow rate.     

Atomic force microscopic study on DNA-wrapping for different diameter single-wall carbon nanotubes

DNA-wrapped single-wall carbon nanotubes (DNA-SWNT hybrids) prepared from different diameter HiPco- and Arc-SWNTs were investigated by atomic force microscopy. The mean diameter of DNA-HiPco-SWNT hybrids is 1.94 nm that is consistent with one HiPco-SWNT (~ 0.9 nm) wrapped by DNA (~ 1 nm). On the other hand, the mean diameter of DNA-Arc-SWNT hybrids is 3.74 nm that can correspond to one Arc-SWNT (~ 1.4 nm) wrapped by several layers of DNA. It is suggested that the DNA-wrapping mechanism for large diameter Arc-SWNTs is different from that for small diameter HiPco-SWNTs.