Influence of generator load conditions on third-harmonic voltages in generator stator winding

The influence of changes in load conditions of the generator-transformer unit on the operating conditions of the 100% ground-fault protection of the generator stator winding based on the third-harmonic voltages was analyzed. The analyzed stator ground-fault protection system is by ratio of the voltages third harmonic in generator neutral and at the generator terminals. The third-harmonic voltages were determined on the base of the experimental tests (measurements) run in real conditions at changes in active and reactive load conditions of the generator. It was found that mainly the generator active load influences the voltage feeding the measuring element of ground-fault protection. Therefore, determining operating conditions of ground-fault protection the influence of the generator active and reactive load should be deeply considered. This can ensure the proper operation of the ground-fault protection based on the voltage third harmonics in the whole range of the changes in generator load. Considering the influence of changes in generator load on the third-harmonic voltages (feeding measuring element of the protection system) will allow eliminating irregular generator tripping as a result of unselective operation of these protections.     

Application of piece‐wise linear weight functions for 2D 8‐node quadrilateral element in contact problems

The present study is a continuation of our previous work with the aim to reduce problems caused by standard higher order elements in contact problems. The difficulties can be attributed to the inherent property of the Galerkin method which gives uneven distributions of nodal forces resulting in oscillating contact pressures. The proposed remedy is use of piece‐wise linear weight functions. The methods to establish stiffness and/or mass matrix for 8‐node quadrilateral element in 2D are presented, i.e. the condensing and direct procedures. The energy and nodal displacement error norms are also checked to establish the convergence ratio. Interpretation of calculated contact pressures is discussed. Two new 2D 8‐node quadrilateral elements, QUAD8C and QUAD8D, are derived and tested in many examples, which show their good performance in contact problems. Copyright © 2004 John Wiley & Sons, Ltd.     

Analysis of operating conditions of ground-fault protection schemes for generator stator winding

This paper presents results of simulation studies of the influence of methods of grounding the stator winding of the unit-connected generator neutral on the operating conditions of a 100-percent ground-fault protection excited by the third-harmonic voltage ratio in the generator neutral and at its terminals. The analysis was performed for a generator with the neutral grounded through a ground-fault neutralizer, a third-harmonic stop filter, a resistor, and a capacitive voltage divider. The influence of the parameters of the particular elements of the grounding circuits on the voltage-feeding measuring element of the protection was determined. The capacitance to ground of the generator breakers was taken into account. The simulations were run for 1110-MVA unit-connected generator at ground faults along the whole length of the generator stator winding. It has been found that the method of grounding the generator neutral and the parameter of the grounding elements significantly influences the operating conditions of this protection. It is shown that through the proper selection of these parameters, the ground-fault protection of whole stator winding, counting from the generator neutral to the terminals is ensured.     

Simulation of Temperature Distribution in Stored Wheat without Aeration

A neural-deterministic simulation model applied for calculating distributions of temperatures and moisture content in a bed of wheat stored in a steel silo without aeration is presented in the article. The model consists of differential equations of heat and moisture transfer, initial and boundary conditions, and three artificial neural networks used during simulated ambient air conditions. Experiments and computer simulations were carried out in order to determine temperature fields in wheat grain stored in a steel silo for two months. The computer simulations were carried using MATLAB and FEMLAB software. The difference between measured and simulated temperature in grain near the silo wall at a height of 2.5 m from the bottom was less than 3.0°C. On the basis of the analysis performed it was concluded that the temperature distributions obtained with the model were consistent with the measured results obtained for grain stored in a steel silo without aeration.     

Microprocessor debugging techniques and their application in debugger design

Every microprocessor-based system needs powerful debugging tools. Debugging power strongly depends on a mechanism of control exchange between the debugger and an application program. Several implementation methods of such a mechanism are briefly described and compared in this paper. It is shown that conditional breakpoints facilitate a semantics-oriented approach to program debugging. Some debugging techniques derived from elementary control-exchange mechanisms are proposed. Most of the techniques discussed are implemented in the MD-86 debugger designed for the Intel 8086 microprocessor. The debugger itself is also briefly described.     

The influence of biomass co-combustion on boiler fouling and efficiency

The paper presents an attempt to evaluate the influence of biomass co-combustion on the fouling of boiler convection surfaces. In order to show the influence of co-firing biomass with bituminous coal on boiler efficiency, the calculations of pulverized fuel (PF) OP 140 steam generator have been carried out. Typical Upper Silesian coal with medium fouling inclination has been chosen as a basic fuel. Three kinds of biomass have been taken into consideration: straw, wood and dried sewage sludge. The results confirm that the properties of additional fuels cause deterioration of the boiler efficiency as well as the changes in boilers operational parameters (amount of water injected in attemperators, ash stream, hot air temperature). The biomass during cofiring in fact replaces the coal, but always the additional fuel consumption is higher than that of the substituted coal. Therefore, the actual decrease of coal consumption is smaller than the thermal fraction of the biomass.