Formation and retention of local melted films in AZ91 friction stir spot welds

The formation of local melted films during friction stir spot welding of as-cast AZ91D and thixomolded AZ91 material is investigated. The average temperatures close to the tip of the rotating pin vary from 438 to 454 °C during the dwell period in friction stir spot welding. These measured temperature values are higher than the melting temperature of α-Mg + Mg₁₇Al₁₂ eutectic (437 °C). It is suggested that the temperature in the stir zone during the dwell period is determined by the relative proportions of α-Mg and (α-Mg + Mg₁₇Al₁₂) eutectic material, which are incorporated during friction stir spot welding. Based on the stir zone temperature measurements and a detailed examination of material located at the root of the pin thread it is suggested that material is moved downwards via the pin thread and into the stir zone during the dwell period in friction stir spot welding. Evidence of local melted film formation is observed in the stir zone of AZ91 spot welds. It is suggested that melted films are retained since their dissolution rate is much slower in the high temperature stir zone than it is when melted films is formed in the stir zone during Al 7075-T6 friction stir spot welding. The spontaneous melting temperature, solute diffusion rate and the thermodynamic driving force for droplet dissolution are much higher during Al 7075-T6 friction stir spot welding.     

Clonality in hepatocellular carcinoma: analysis of methylation pattern of polymorphic X-chromosome-linked phosphoglycerate kinase gene in females

Analysis of X-chromosome inactivation patterns in women has been used to assess the clonality of various tumors. In this report, we analyzed 27 liver tumors in women, including 18 samples obtained by the performance of ultrasonically guided thin-needle biopsies. By analysis of the heterogeneity of phosphoglycerate kinase gene, 11 of 27 (41%) cases were found to be heterozygous at the gene. Of these informative 11 cases with liver tumors, 7 cases were "large" tumors (> 25 mm in diameter) and 4 cases were "small" tumors (< 25 mm in diameter). All 7 large tumors showed monoclonal patterns by the phosphoglycerate kinase gene analysis. Of the 4 small tumors, 2 showed monoclonal, and 2 showed polyclonal patterns. The 2 with monoclonal patterns were pathologically diagnosed as hepatocellular carcinoma despite their small sizes (20 mm and 23 mm). Of the two with polyclonal patterns, the smallest one (15 mm) was diagnosed as benign adenomatous hyperplasia, and the other as hepatocellular carcinoma heavily infiltrated by lymphocytes. These data suggest that analysis of the methylation pattern of the phosphoglycerate kinase gene may be helpful on rare occasions in elucidating the nature of liver tumors but must in fact be used in conjunction with histological appearances to avoid errors secondary to inflammatory infiltrates.     

Characteristics of hydrogen-assisted intergranular fatigue crack growth in interstitial-free steel: role of plastic strain localization

The behavior of intergranular fatigue crack growth in an interstitial-free (IF) steel in a hydrogen environment was investigated at different frequencies. Focusing on the plastic strain localization, we observed details of the striation-like feature on the intergranular fracture surface, slip behavior around microvoids, and crystallographic orientation gradient underneath the fracture surface. It was determined that the intergranular fatigue crack growth mechanism in the IF steel is microvoid formation at the crack tip and subsequent coalescence with the crack. Moreover, it was found that the grain boundaries, acting as propagation paths, suffer from pre-damage arising from plastic strain localization near the grain boundaries even before the main crack propagates to a certain location. Therefore, fatigue cracks in a hydrogen environment easily propagate to the grain boundaries. The frequency dependence of fatigue crack growth in the hydrogen environment is significantly smaller than that in a low carbon steel, probably because of the frequency dependence of the pre-damage evolution behavior.     

Germanium recovery using polyphenol microspheres prepared by horseradish peroxidase reaction

BACKGROUND: The formation of polyphenol microspheres by the polymerization of 3‐methylcatechol was performed in a methanol/phosphate buffer solution using horseradish peroxidase (HRP), without the use of a surfactant or a water/oil interface, to be used for germanium recovery. RESULTS: The polyphenol microspheres were of diameter 1 mm. The functional group density of phenol group in the polymer was approximately 15 mol kg^?1 determined by the Folin‐Denis method. In batchwise experiments, the amount of germanium adsorbed was 0.23 mol kg^?1. CONCLUSION: Because germanium is a rare metal, a system for its recovery is required. Using the proposed system, continuous recovery of germanium can be achieved using multilayered microspheres. Copyright © 2011 Society of Chemical Industry     

An EDTA-associated anti-B agglutinin: the role of ionized calcium

BACKGROUND: It is believed that EDTA-dependent panagglutination is associated with free carboxylic acids that support reactions of rare autoagglutinins. CASE REPORT: An ABO typing discrepancy occurred in an 88-year-old patient. The specificity of his autoagglutinin was demonstrated by panel cell study and absorption tests using normal donors' red cells or immunoadsorbents coated with A, B, or O substances. Inhibition assays were performed to determine whether the autoagglutinin was inhibited by ionized calcium or carboxylic acids. The autoagglutinin had anti-B specificity when tested in the presence of EDTA. It was neutralized by group B secretor saliva and adsorbed by crystalline silica coated with simple B substances with or without EDTA, although it was absorbed by group B red cells only in the presence of EDTA. The agglutinating activity was stronger at 25 degrees C (titer 64) than at 37 degrees C (titer 16) and was destroyed by treatment of the serum with dithiothreitol, which suggests that the autoagglutinin is IgM. This activity also appeared in the patient's serum after dialysis and in an eluate obtained after adsorption with simple B substances, and it was inhibited by the addition of CaCl2 at 0.5 mM or higher concentrations. This suggests that the agglutination is not dependent on EDTA but, rather, on the concentration of ionized calcium. The autoagglutinin failed to react with group B red cells treated with glutaraldehyde for 10 minutes. CONCLUSION: An anti-B autoagglutinin was shown to have caused an ABO typing discrepancy in the presence of EDTA. These results suggest that autoagglutination requires an environment with low levels of ionized calcium, but not the presence of carboxyl groups.     

Local melting and tool slippage during friction stir spot welding of Al-alloys

Local melting and tool slippage during friction stir spot welding of different Al-alloy base materials is examined using a combination of detailed microscopy and temperature measurement. The stir zone peak temperature during welding is limited by either the solidus of the alloy in question or by spontaneous melting of intermetallic particles contained in the as-received base material. When spontaneous melting occurs this facilitates tool slippage at the contact interface. Accurate stir zone temperature and grain size measurements are essential elements when estimating the strain rate using the Zener–Hollomon relation. In Al 2024 and Al 7075 spot welds spontaneous melting of second-phase particles produces a drastic reduction in strain rate values. In Al 5754 and Al 6061 spot welds there is a strong correlation between tool rotational speed and estimated strain values. Local melted films dissolve rapidly in the high temperature stir zone and when the spot weld cools to room temperature following welding. Evidence of local melting is observed in Al 7075 friction stir spot welded joints made using a combination of rapid quenching, high plunge rates, and extremely short dwell time settings.