Temperature and pressure effects on supercritical CO2 extraction of tomato seed oil

Tomato seed oil was extracted with supercritical carbon dioxide in a semibatch-flow extractor within the temperature range 313–343 K and the pressure range 10.8–24.5MPa. The extraction rates increased with pressure, but decreased with temperature increase because of the variation in solvent density and resultant differences in oil solubility. The fatty acid composition of the extracted oil was similar to that of soybean oil.     

A new write/erase method to improve the read disturbcharacteristics based on the decay phenomena of stress leakage currentfor flash memories

This paper describes a new write/erase method for flash memory to improve the read disturb characteristics by means of drastically reducing the stress leakage current in the tunnel oxide. This new write/erase operation method is based on the newly discovered three decay characteristics of the stress leakage current. The features of the proposed write/erase method are as follows: 1) the polarity of the additional pulse after applying write/erase pulse is the same as that of the control gate voltage in the read operation; 2) the voltage of the additional pulse is higher than that of a control gate in a read operation, and lower than that of a control gate in a write operation; and 3) an additional pulse is applied to the control gate just after a completion of the write/erase operation. With the proposed write/erase method, the degradation of the read disturb life time after 10⁶ write/erase cycles can be drastically reduced by 50% in comparison with the conventional bipolarity write/erase method used for NAND type flash memory. Furthermore, the degradation can he drastically reduced by 90% in comparison with the conventional unipolarity write/erase method fur NOR-, AND-, and DINOR-type flash memory. This proposed write/erase operation method has superior potential for applications to 256 Mb flash memories and beyond     

Fracture toughness measurement with fatigue-precracked single edge-notched beam specimens of WC-Co hard metal

The plain-strain fracture toughness of WC-8%Co hard metal, K _IC, was measured using single edge-notched beam (SENB) specimens with fatigue precrack. The fatigue precrack was introduced with compressive fatigue cycling in four-point bending at room temperature. Since stable fatigue-crack propagation was obtained from the notch tip, it was easy to control the fatigue-precrack length. A reasonable K _IC value of 13.3 MPa m^1/2 was obtained with the fatigue-precracked SENB specimens in four-point bending. The compressive fatigue-precracking technique in four-point bending was simple and convenient, and is therefore applicable to precracking in a variety of brittle materials prior to fracture-toughness measurements.     

NiCoFe/C cathode electrocatalysts for direct ethanol fuel cells

A direct ethanol fuel cell (DEFC), which is less prone to ethanol crossover, is reported. The cell consists of PtRu/C catalyst as the anode, Nafion^® 117 membrane, and Ni–Co–Fe (NCF) composite catalyst as the cathode. The NCF catalyst was synthesized by mixing Ni, Co, and Fe complexes into a polymer matrix (melamine-formaldehyde resins), followed by heating the mixture at 800 °C under inert atmosphere. TEM and EDX experiments suggest that the NCF catalyst has alloy structures of Ni, Co and Fe. The catalytic activity of the NCF catalyst for the oxygen reduction reaction (ORR) was compared with that of commercially available Pt/C (CAP) catalyst at different ethanol concentrations. The decrease in open circuit voltage (V_oc) of the DEFC equipped with the NCF catalysts was less than that of CAP catalyst at higher ethanol concentrations. The NCF catalyst was less prone to ethanol oxidation at cathode even when ethanol crossover occurred through the Nafion^®117 film, which prevents voltage drop at the cathode. However, the CAP catalyst did oxidize ethanol at the cathode and caused a decrease in voltage at higher ethanol concentrations.     

Multiobjective dynamic load-dispatching method for optimal operation of power systems

A new practical method is proposed which gives a quasi-optimal solution of the dynamic load-dispatching problem formulated by a multiconstraint multiobjective optimization problem. Here, the multiple constraints are rate reserve constraints and power flow ones, and the multiple objectives are fuel cost and CO₂ emission. The proposed method is an integration of the following three techniques: (1) “Group Dispatch Scheme,” which is developed by the authors, is used to satisfy a violated constraint easily. This scheme consists of three steps. The first step is to classify all generators into two groups. One is the group which should be more loaded to satisfy the violated constraint, and the other is the should-be less loaded group. The second step is to add some load to the former group, and to subtract the same load from the latter. The third step is to dispatch each group load to each groups generators, respectively; (2) the dynamic load-dispatching algorithm is used which provides, in practical time, quasi-optimal generation trajectories; (3) the conventional weighting parametric method is used to obtain a Pareto optimal solution of multiobjective problems. The effectiveness of the method is clarified by a computer simulation on the actual power system of Kansai Electric Power Company.     

Handling of fine-particles by time-averaged particle driving method in plasmas

We developed a noble technique for the fine-particle handling in plasmas. In this method a pair of point electrodes are introduced in the plasma, to which positive pulses are applied alternatively. When the pulse repetition period is shorter than the particle response time, the particles feel only time-averaged force because of their large mass. Spatial profile of the equivalent potential of the time-averaged force varies from a circle to an ellipse with an increase in the local discharge at the electrodes. The particles are eventually transported toward a middle point between two point-electrodes, being almost independent of their initial positions. This method is quite effective for converging fine particles in the plasma.     

A distribution kinetics model for chromatography of block-like molecules

We develop the theory for chromatographic separation of isomers such as polycyclic aromatic hydrocarbons, polychlorinated biphenyls, dioxins, steroids, and carotenoids based on shape-selective mechanisms for either exclusion or adsorption. Block-like solute transport and retention on oriented stationary phases are modeled by a dispersed-flow chromatographic equation combined with simultaneous exclusion partitioning and shaped-based adsorption. Molecules to be separated are considered distributed continuously with respect to the shape and sorption parameters. The population balance equations of distribution kinetics provide the governing differential equations that are solved for the temporal moments of the concentration in a chromatographic column. By including dispersive mass transport effects, the model allows estimation of peak variance and HETP and is thus an improvement over theories that focus solely on retention time. The model predictions are compared with experimental data from the literature for gas chromatography.     

In Situ Synthesis and Microstructures of Tungsten Carbide-Nanoparticle-Reinforced Silicon Nitride-Matrix Composites

A W₂C-nanoparticle-reinforced Si₃N₄-matrix composite was fabricated by sintering porous Si₃N₄ that had been infiltrated with a tungsten solution. During the sintering procedure, nanometer-sized W₂C particles grew in situ from the reaction between the tungsten and carbon sources considered to originate mainly from residual binder. The W₂C particles resided in the grain-boundary junctions of the Si₃N₄, had an average diameter of ∼60 nm, and were polyhedral in shape. Because the residual carbon, which normally would obstruct sintering, reacted with the tungsten to form W₂C particles in the composite, the sinterability of the Si₃N₄ was improved, and a W₂C–Si₃N₄ composite with almost full density was obtained. The flexural strength of the W₂C–Si₃N₄ composite was 1212 MPa, ∼34% higher than that of standard sintered Si₃N₄.     

Freestream and vortex preservation properties of high-order WENO and WCNS on curvilinear grids

Freestream and vortex preservation properties of a weighted essentially nonoscillatory scheme (WENO) and a weighted compact nonlinear scheme (WCNS) on curvilinear grids are investigated. While the numerical technique used for the compact difference scheme can be applied to WCNS, applying it to WENO is difficult. This difference is caused by difference in the formulation of numerical fluxes. WENO computed in the generalized coordinate system does not work well for either freestream or vortex preservation, whereas WENO computed in the Cartesian coordinate system works well for both freestream and vortex preservation, but its resolution is lower than that of WCNS. In addition, WENO in the Cartesian coordinate system costs three times as much as WENO or WCNS in the generalized coordinate system. Therefore, WENO in the Cartesian coordinate system is not suitable for solving Euler equations on a curvilinear grid. On the other hand, WCNS computed in the generalized coordinate system works well for freestream and vortex preservation when used with the numerical technique proposed for the compact difference scheme. The results show that WCNS with this numerical technique can be used for an arbitrary grid system. In this paper, the excellent freestream and vortex preservation properties of WCNS when used with the numerical technique, compared with those of WENO, are shown for the first time.