Prediction and optimization of electroplated Ni-based coating composition and thickness using central composite design and artificial neural network

Journal of Applied Electrochemistry - The choice of the electroplating conditions of Ni-based alloys has always been a serious research question. In this study, an artificial neural network based...     

Experimental analysis of fuel from fish processing industry waste in a diesel engine

In the present work, biofuel derived from industrial fish processing industry waste is used in diesel engines to study its suitability . Biofuel from industry fish waste is produced through catalytic cracking, and its quality has been improved through distillation. A single cylinder 4.5 kW at 1500 rpm was used to find the suitability of biofuel and undistilled biofuel in diesel engine. Experimental results show that the brake thermal efficiency of biofuel and undistilled biofuel is similar. Brake thermal efficiency for diesel, undistilled biofuel and biofuel is 29.98, 32.12 and 32.4%, respectively, at 80% load. Carbon monoxide, unburnt hydrocarbons, particulate matter and oxides of nitrogen emissions increase with undistilled biofuel compared to biofuel. There is a small reduction in carbon dioxide emission with undistilled biofuel compared to biofuel. Even though the cylinder pressure is high with undistilled biofuel, the intensity of premixed combustion is lower than distilled biofuel. The ignition delay and combustion duration increase with undistilled biofuel. Finally, it is concluded that the fuel derived from fish processing industry waste can be used as a fuel for diesel engine after distillation.     

Hybrid micro electrostatic actuator

A hybrid micro-electrostatic actuator is presented. The actuator integrates a vertical comb driving (VCD) unit and a parallel-plate driving (PPD) unit. The hybrid actuator is fabricated using a one structural layer microfabrication process, i.e., MetalMUMPs instead of a two-layer microfabrication process needed for traditional vertical comb-drive actuators by taking advantage of the residual stress gradient in the MetalMUMPs nickel layer, which raises the moving parts of the actuator above the substrate after release. The hybrid actuator significantly simplifies the fabrication process for vertical comb-drive actuators, i.e., turning a process requiring two structural layers into a process requiring only one structural layer and thus avoids any misalignment between the two layers. The hybrid actuator can generate larger force and then a larger displacement than the actuator having only the VCD with the same area since no extra space is needed for the PPD unit which uses the moving electrode existing in the VCD unit and a fixed electrode under the VCD unit. The VCD and PPD units in the hybrid actuator are subject to the same driving voltage and work together to pull the moving parts of the actuator downward. A model is established for the hybrid actuator to analyze its displacement. The analytical results show that displacement of the moving part of the hybrid actuator is about half of the gap between the electrodes of the PPD unit. Prototypes are fabricated and tested. With a driving voltage of 150 V, the hybrid actuator achieved a measured displacement of 6.48 µm.     

Steam reforming of methanol over ruthenium impregnated ceria,alumina and ceria–alumina catalysts

The wet impregnation method was used to prepare different ruthenium promoted Ce–Al catalysts. These catalysts were used in the steam reforming of methanol reaction (SRM). The effects of the reaction temperature (200–400 C) and the catalyst composition were studied for optimization reasons. The steam to methanol molar ratio was kept constant (S/M = 2). The promotion of cerium/aluminum oxides with Ru enhanced their catalytic activity. The catalytic test results showed that the Ru/Ce combination was the most beneficial. The synergy between Ru and cerium oxide led to the formation of active sites with excellent redox properties. For high active phase content, the 5 RuCe catalyst exhibited the highest hydrogen production amount with no CO formation. This catalyst was kept under stream for 5 days at 400 C, and no significant deactivation was observed. Copyright © 2016 John Wiley & Sons, Ltd.     

Deposition of hybrid 3-GPTMS's film on AA2024-T3: Dependence of film morphology and protectiveness performance on coating conditions

This paper describes the elaboration of 3-glycidoxypropyltrimethoxysilane (3-GPTMS) films onto AA2024-T3 aluminum alloy for corrosion protection.The dependence of sol–gel morphology on both precipitation under cathodic polarization and nitrate incorporation was investigated via scanning electron microscopy (SEM).Once added into silanization solution, sodium nitrate promoted the reaction of silane condensation and enhanced the film compactness.Electrochemical impedance spectroscopy results (EIS) indicated that doping silane film with NaNO₃ ameliorated its barrier property and protectiveness. Silane films applied onto AA2024-T3 surface by using potentiostatic method, exhibited obviously higher corrosion resistance than those obtained by conventional “dip-coating” method. The resistance of coating is accentuated when not very negative potential was applied.     

Destructive polyarthritis in Behcet's disease. Apropos of a case and review of the literature]

The authors report a case of a 37 years old man with Beh?et's disease since 7 years who develops a destructive chronic polyarthritis involving wrists, hands and one knee. The parallel evolution between recurrent orogenital ulceration and arthritis added to the absence of other associated destructive rheumatism permit to link this polyarthritis to Beh?et disease. In spite of the few reports, the occurrence of destructive arthritis can't exclude absolutely the diagnosis of this affection.     

Dynamic theoretic proactive caching placement game for energy saving in H‐CRAN

Edge caching is an effective feature of the next 5G network to guarantee the availability of the service content and a reduced time response for the user. However, the placement of the cache content remains an issue to fully take advantage of edge caching. In this paper, we address the proactive caching problem in Heterogeneous Cloud Radio Access Network (H‐CRAN) from a game theoretic point of view. The problem is formulated as a bargaining game where the remote radio heads (RRHs) dynamically negotiate and decide which content to cache in which RRH under energy saving and cache capacity constraints. The Pareto optimal equilibrium is proved for the cooperative game by the iterative Nash bargaining algorithm. We compare between cooperative and noncooperative proactive caching games and demonstrate how the selfishness of different players can affect the overall system performance. We also showed that our cooperative proactive caching game improves the energy consumption of 40% as compared with noncooperative game and of 68% to no‐game strategy. Moreover, the number of satisfied requests at the RRHs with the proposed cooperative proactive caching scheme is significantly increased.     

Miniaturized Optical Fiber Sensor Interrogation System Employing Echelle Diffractive Gratings Demultiplexer for Potential Aerospace Applications

To enable the application of optical fiber sensors to aerospace vehicles, the sensor interrogation or data acquisition system has to meet small size and low weight requirements. This paper presents the developmental work of an echelle diffractive gratings (EDGs) demultiplexer-based optical fiber sensor interrogation system. The operation principle of this system and its application to fiber Bragg grating (FBG) sensor interrogation are presented. The experimental results have shown that the developed interrogator (not including the electronic controller) weighs less than 60 g and provides better than 1 pm measurement resolution and better than plusmn10 pm measurement accuracy.     

Influence of air drying temperature on kinetics,physicochemical properties,total phenolic content and ascorbic acid of pears

This study was conducted to evaluate quality and structural changes in parallelepipedic pieces of pears during convective drying at different air temperatures (30–70 °C).Submitted to atmospheric O₂ conditions, ascorbic acid deterioration demonstrated first-order kinetic behaviour and was found to depend on air temperature and pear moisture content. Loss of ascorbic acid content increased with increasing air temperature. Possible explanation could be the irreversible oxidative reaction occurring during drying. Phenol content degradation fitted a pseudo first-order reaction and was significantly influenced by air temperature.Variations in bulk density, shrinkage and porosity essentially depended on changes in moisture content. Porosity exhibited a nonlinear variation with respect to moisture content. Volume change showed, as expected, a linear variation with moisture content. Drying temperature significantly induced the increase of a* and b* colorimetric parameters due to non-enzymatic browning reaction, which turned the samples more reddish and yellow when the temperature rose.