Impacts of varnishes and impregnation chemicals on combustion properties of oak (Quercus petreae lipsky)

This study was performed to determine the effects of varnishing after impregnation with boron compounds on combustion properties of oak. For this aim, the test samples prepared from oak (Quercus petreae Liebl.) wood were impregnated according to ASTM D 1413‐99 with boric acid (Ba) and borax (Bx) by vacuum technique. After impregnation, surfaces were coated by cellulosic (Cv), synthetic (Sn), polyurethane (Pu), waterborne (Wb), acrylic (Ac), and acid hardening (Ah) varnishes in accordance to ASTM D 3023. Combustion properties of samples after varnishing process were determined, according to ASTM E 160‐50. According to material and process types, combustion temperature was the highest in Bx and Cv, the lowest in Ba and Ac. An important difference was not observed between without flame source combustion (WFSC) and flame source combustion (FSC). According to combustion type, impregnation material and varnish type, combustion temperature was the highest value in WFSC + Bx + acid hardening varnish combination and the lowest in WFSC + Ba + acrylic varnish combination. As a result, the tested varnishes showed an increasing impact but boron compounds showed a decreasing impact on combustion properties of oak. In consequence, for usage areas having a high risk of fire, impregnation of wood material with boron compounds before varnishing will decrease combustion temperature and provide security. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Comparison between some empirical equations of state for polymers

Some commonly used empirical equations of state for polymers are considered: the Spencer-Gilmore equation with two and three adjustable parameters, the Whitaker-Griskey equation, and the Rehage-Breuer equation. Also, a new equation is proposed: the Inverse Volume equation. These equations are evaluated with regard to fitting experimental P-V-T data and agreement with experimental data on isothermal compressibility and thermal expansion coefficient. The adjustable parameters for each equation are determined with the help of Rosenbrock's optimum-seeking technique. Analysis of the residuals on specific volume for a variety of materials suggests that the Spencer-Gilmore equation with three adjustable parameters, the Rehage-Breuer and the Inverse Volume equations yield the smallest and most random residuals and thus the least systematic error. The same three equations mentioned above yield results in good agreement with experimental isothermal compressibility data. However, among all the equations considered in this study, the Inverse Volume equation yields the best agreement with experimental thermal expansion coefficient data. Furthermore, it is the only equation to correctly predict the rise in thermal expansion coefficient with increasing temperature.     

Characteristics of Er-doped Al2O3 thin filmsdeposited by reactive co-sputtering

Er-doped Al₂O₃ thin films have been deposited by reactive co-sputtering onto thermally oxidized Si-wafers. The deposition process has been optimized with respect to the requirements originating from the application of these multilayer structures as integrated optical amplifiers for the third telecom window, i.e., the wavelength range 1.52-1.55 μm. The films obtained at a substrate temperature of only 400°C are amorphous and show a homogenous structure, without columns or grains. For slabguides, background losses smaller than 0.25 dB/cm have been obtained, even without any annealing. A relatively broad luminescence band, having an FWHM of ~55 nm around the 1.533-μm wavelength, has been measured. From gain versus pumping power curves, an upconversion coefficient lower then 20·10^-25 m³/s has been derived, being half of the values reported up to now in the literature. Simulations based on experimentally determined material parameters and assuming a channel attenuation of 0.5 dB/cm indicate, for 0.24 at.% Er channel devices with an optimal channel length of 7.7 cm, an amplification of 8 dB at 1.533 μm for a pump wavelength of 1.48 μm, and a pump power of only 8.7 mW     

Ti3AlC2 coated D-shaped fiber saturable absorber for Q-switched pulse generation

In this letter, a titanium aluminum carbide (Ti3AlC2) coated D-shaped fiber is proposed and demonstrated as a new saturable absorber (SA) for Q-switched laser pulse generation. In preparing the SA, the Ti3AlC2 powder is dispersed in liquid polyvinyl alcohol (PVA) before the solution is dropped and left to dry onto a polished surface of D-shape fiber. The SA is added to an erbium-doped fiber laser (EDFL) cavity to modulate the cavity loss for Q-switching. The Q-switched laser is obtained at 1 561 nm. The pulse width of the pulses can be varied between 7.4 µs and 5.1 µs with a corresponding repetition rate range from 41.26 kHz to 54.35 kHz, when the pump power is increased from 42.2 mW to 71.5 mW. At 71.5 mW pump, the pulse energy is obtained at 70.3 nJ. The signal-to-noise ratio (SNR) of the fundamental frequency is recorded at 67 dB, which indicates the stability of the laser.     

On the capacity of the state‐dependent interference relay channel

This paper considers the state‐dependent interference relay channel (SIRC) in which one of the two users may operate as a secondary user and the relay has a noncausal access to the signals from both users. For discrete memoryless SIRC, we first establish the achievable rate region by carefully merging Han‐Kobayashi rate splitting encoding technique, superposition encoding, and Gelfand‐Pinsker encoding technique. Then, based on the achievable rate region that we derive, the capacity of the SIRC is established in many different scenarios including (a) the weak interference regime, (b) the strong interference regime, and (c) the very strong interference regime. This means that our capacity results contain all available known results in the literature. Next, the achievable rate region and the associated capacity results are also evaluated in the case of additive Gaussian noise. Additionally, many numerical examples are investigated to show the value of our theoretical derivations.     

Varnish layer hardness of oriental beech (fagus orientalist L.) wood as affected by impregnation and bleaching

The impacts of impregnation and bleaching on the varnish layer hardness of Oriental beech (Fagus orientalist L.) wood were investigated. A number of bleaching combinations {[NaOH−H₂O₂], [NaOH−Ca(OH)₂−H₂O₂], [NaOH−MgSO₄−H₂O₂] [NaHSO₃−H₂C₂O₄], [NaSiO₃−H₂O₂], [KMnO₄+NaHSO₃+H₂O₃]} were applied at 18% concentration for bleaching to both impregnated and unimpregnated specimens of Oriental beech wood. Subsequently, water-based (WB) varnish was coated over the samples and the varnish layer hardness values were determined in accordance with ASTM D 4366-95. All of the chemicals used for bleaching reduced the surface hardness. However, after varnish coating, the hardness of most samples was similar to that of the varnish-coated natural (control) samples.     

Effect of roasting on the physico-chemical properties,fatty acids,polyphenols and mineral contents of tobacco (Nicotiana tabacum L.) seed and oils

The physico-chemical properties, phytochemicals, mineral contents of tobacco (Nicotiana tabacum L.) seeds grown at Samsun province in Turkey were evaluated. The oil contents of tobacco seeds ranged from 20.6% (control) to 29.0% (microwave-roasted). L*, a* and b* values of tobacco seeds ranged from 32.38 to 35.61; from 6.32 to 6.78; from 13.72 to 14.27, respectively. Total phenolic contents of tobacco seed extract and oils were reported between 31.02 (oven-roasted) and 34.42 mg GAE/100 g (microwave-roasted) to 4.60 (microwave-roasted) and 6.45 mg GAE/100 g (oven-roasted), respectively. Total flavonoid values of raw and roasted tobacco seed extract and oils were determined between 26.62 (oven) and 67.10 mg/100 g (control) to 21.57 (control) and 44.71 mg/100 g (microwave-roasted), respectively. Gallic acid, 3,4-dihydroxybenzoic acid and catechin are the predominant phenolic components of raw and roasted tobacco seed oils. The amounts of oleic and linoleic acid in raw and roasted tobacco seed oils ranged from 10.23% (oven-roasted) to 12.48% (control) and 73.72% (control) to 76.63% (oven-roasted), respectively. The abundant elements found in seeds were K, P, Ca, Mg, S and Fe. The mineral amounts of the roasted seeds were found higher than that of the control. The highest increase was detected in oven roasted tobacco seeds.