Power swing analysis in a future metropolitan electric power system on a contingent trip of cryogenic high-power cables

A cryogenic power cable is expected to be capable of carrying bulk power as a main transmission line in a future metropolitan electric power system. It is important to establish a strategy of how to sustain power supply when such a highly densified power supply route trips from the network due to contingency. It is proposed here that the bulk power transmitted by the cryogenic cable could be distributed into the parallel conventional transmission lines by suitable circuit breaker operations in the system. In this process, power-flow routes are forced to be changed with a remarkable modification in the system configuration. In this paper, the power swings associated with the large power-flow change following contingent faults are analyzed by means of a transient network analyzer. It is found that the proposed system modification could be realized without any harmful power swing if the parameters in generators as well as in control devices have conventional magnitudes. It is shown also by simulations that the margin to occurrence in an unstable power swing is left sufficient even if the parameters deviate somewhat from the present magnitudes.     

Development of cable fault location method using fiber optic distributed temperature sensor

When ground-fault problems occur on a cable line, immediate fault location and restoration are required. Therefore, various new methods to locate the fault point instantaneously have been investigated to replace such conventional methods as the Murray loop method and the pulse radar method [1]. These methods require a long time to locate the fault point. One possible fault location method is to sense the temperature rise following a ground fault using a fiber optic distributed temperature sensor. Application of this method was found feasible through sensing the temperature rise at a ground-fault test using a thermocouple as a temperature sensor with test cables [4]. A power/optical composite cable was prepared experimentally and after verifying its thermal mechanical performance, the temperature rise at an incidence of a fault was determined and the anticipated performance was demonstrated in a ground-fault test. This article describes the outline of the test.     

A novel technique for a DC brushless motor without position sensors

A dc brushless motor is a kind of synchronous motor driven by an inverter and requires sensors to detect the rotor position. As one of the methods, the induced voltages of a brushless motor have been utilized in practice. However, there are some problems in this method, e.g., the motor can obtain insufficient torque due to the low induced voltages in a low-speed range. This paper proposes a new method which controls the inverter angular frequency ω₁ by using inherent characteristics wherein the torque current i_r is almost proportional to the internal phase angle φ where the primary flux of a synchronous motor is controlled to be constant. If the parameters of a motor are given exactly, the speed regulation is quite small and the transient characteristics with high response and high starting torque are obtained. Furthermore, it is possible to operate a synchronous motor in the field-weakening range. Here, the principle of the control method and the performance characteristics of a dc brushless motor having no position sensors are discussed. The simulation and the experimental results of the tested machine show that the proposed method is very useful for practical applications.     

Vivid image projection system using e‐Paper active screen

Projected image on a screen is not always vivid enough when it is projected in a bright room. We generally have to choose either vivid image in a dark room or dull image in a bright room. We have suggested a new projection system which can realize high contrast image projection in a bright room. It is consisted of electronic paper screen, projector, and light‐emitting diode room light. The electronic paper (e‐Paper) screen alternates its whole surface white/black with 120 Hz. Room lights are controlled with the same frequency of 120 Hz with the opposite phase as that of the e‐Paper screen. We have confirmed that our new system has achieved higher contrast than the conventional projection system and also enough readability of paper documents in the room simultaneously. We have thus confirmed that our new system can bring an ideal condition, for audience, which can realize a vivid image projection in a bright room.     

Crystallization process and magnetic properties of Fe100−x,B x (10 ≦ × ≦ 35) amorphous alloys and supersaturated state of boron inα-Fe

Amorphous specimens of Fe_100–x B _x were prepared in the range 10 × 35 at % B by a single-roller method. The crystallization process and the boron concentration dependence of the Curie temperature were examined by differential scanning calorimetry, X-ray diffraction, Mössbauer spectroscopy and magnetic measurements. Two-step crystallization was observed in specimens with× < 17: amorphous amorphous + boron-supersaturated b c c phase (-Fe(B)) t-Fe₃B +-Fe. A single-Fe(B) phase was not observed. The transition temperature from t-Fe₃B to stable (-Fe + t-Fe₂B) sensitively depends on the boron content in the alloys. The crystallization temperature (T _x) of the amorphous alloys was almost unchanged for 17 × 31, but increased remarkably at high boron concentrations of× 33, where the decomposition products consisted of t-Fe₂B and o-FeB. The Curie temperature (T _c) of the amorphous phase was as low as 480 K at× = 10, increased with increasing boron content up to 820 K and then decreased in the high boron concentration alloys of× > 28. A single-Fe(B) phase was not detected in the as-quenched specimens of× = 8 and 10. The phase coexisted with the o-Fe₃B and amorphous phases. The lattice parameter of the phase was 0.2861₀ nm which was smaller than that of pure iron by 2/1000, indicating the substitutional occupation of boron atoms in the b c c lattice.     

Fast computation of computer-generated hologram using Xeon Phi coprocessor

We report fast computation of computer-generated holograms (CGHs) using Xeon Phi coprocessors, which have massively x86-based processors on one chip, recently released by Intel. CGHs can generate arbitrary light wavefronts, and therefore, are promising technology for many applications: for example, three-dimensional displays, diffractive optical elements, and the generation of arbitrary beams. CGHs incur enormous computational cost. In this paper, we describe the implementations of several CGH generating algorithms on the Xeon Phi, and the comparisons in terms of the performance and the ease of programming between the Xeon Phi, a CPU and graphics processing unit (GPU).     

Observation of 3‐D Structure of Bubbles in a Fluidized Catalyst Bed

The interface area between the bubble and emulsion phases in a fluidized catalyst bed is one of the important parameters used to analyze and design the fluidized bed reactor. We used a fast‐scanning X‐ray CT system to observe the bubble shape and structure. We then obtained the transient 2‐dimensional cross sectional gas‐phase distribution in a fluidized catalyst bed. Using image‐processing techniques, pseudo 3‐dimensional images of the bubbles were reconstructed. The bubble structure was studied based on the 3‐dimensional images and the previously obtained results in a 2‐dimensional fluidized bed. It was found that the bubble shape was not spherical but complicated, and that the bubbles ascending in a fluidized catalyst bed consisted of some smaller bubbles.     

Effects of Annealing on Dielectric Loss and Microstructure of Aluminum Nitride Ceramics

The effect of annealing on tan δ and microstructures of aluminum nitride (AlN) ceramics were explored. Yttria was added as a sintering additive to AlN powders, and the powders were pressureless-sintered at 1900°C for 2 h in a nitrogen flow atmosphere. In succession to sintering, AlN samples were annealed at 720, 970 and 1210°C for 2 and 4 h. Very low tan δ values between 2.6 and 6.0 × 10⁻⁴ at 28 GHz were obtained when the AlN samples were annealed for 4 h at all the annealing temperatures.     

Fracture Energies of Tape-Cast Silicon Nitride with β-Si3N4 Seed Addition

The fracture energies of the tape-cast silicon nitride with and without 3 wt% rod-like β-Si₃N₄ seed addition were investigated by a chevron-notched-beam technique. The material was doped with Lu₂O₃–SiO₂ as sintering additives for giving rigid grain boundaries and good heat resistance. The seeded and tape-cast silicon nitride has anisotropic microstructure, where the fibrous grains grown from seeds were preferentially aligned parallel to the casting direction. When a stress was applied parallel to the fibrous grain alignment direction, the strength measured at 1500°C was 738 MPa, which was almost the same as room temperature strength 739 MPa. The fracture energy of the tape-cast Si₃N₄ without seed addition was 109 and 454 J/m² at room temperature and 1500°C, respectively. On the contrary, the fracture energy of the seeded and tape-cast Si₃N₄ was 301 and 781 J/m² at room temperature and 1500°C, respectively, when a stress was applied parallel to the fibrous gain alignment. The large fracture energies were attributable primarily to the unidirectional alignment fibrous Si₃N₄ grains.