Modeling aviation baggage screening security systems: a case study

Aviation security protects vital national interests, as well as passengers and aircraft. Key components of an aviation security system include baggage and passenger screening devices and operations. Determining how and where to assign (deploy) such devices can be quite challenging. Moreover, even after such systems are in place, it can be difficult to measure their effectiveness. This paper describes how discrete optimization models can be used to address these questions, based on three performance measures that quantify the effectiveness of airport baggage screening security device systems. These models are used to solve for optimal airport baggage screening security device deployments considering the number of passengers on a set of flights who have not been cleared using a security risk assessment system in use by the Federal Aviation Administration (i.e., passengers whose baggage is subjected to screening), the number of flights in this set, and the size of the aircraft for such flights. Several examples are provided to illustrate these results, including an example that uses data available from the Official Airline Guide.     

Properties of poly(ethylene terephthalate)–poly(ethylene naphthalene 2,6‐dicarboxylate) blends with montmorillonite clay

The production and properties of blends of poly(ethylene terephthalate) (PET) and poly(ethylene naphthalene 2,6‐dicarboxylate) (PEN) with three modified clays are reported. Octadecylammonium chloride and maleic anhydride (MAH) are used to modify the surface of the montmorillonite–Na⁺ clay particles (clay–Na⁺) to produce clay–C18 and clay–MAH, respectively, before they are mixed with the PET/PEN system. The transesterification degree, hydrophobicity and the effect of the clays on the mechanical, rheological and thermal properties are analysed. The PET–PEN/clay–C18 system does not show any improvements in the mechanical properties, which is attributed to poor exfoliation. On the other hand, in the PET–PEN/clay–MAH blends, the modified clay restricts crystallization of the matrix, as evidenced in the low value of the crystallization enthalpy. The process‐induced PET–PEN transesterification reaction is affected by the clay particles. Clay–C18 induces the largest proportion of naphthalate–ethylene–terephthalate (NET) blocks, as opposed to clay–Na⁺ which renders the lowest proportion. The clay readily incorporates in the bulk polymer, but receding contact‐angle measurements reveal a small influence of the particles on the surface properties of the sample. The clay–Na⁺ blend shows a predominant solid‐like behaviour, as evidenced by the magnitude of the storage modulus in the low‐frequency range, which reflects a high entanglement density and a substantial degree of polymer–particle interactions. Copyright © 2005 Society of Chemical Industry     

Wavelength-switchable fiber laser using acoustic waves

We report a wavelength-switchable fiber ring laser that includes a Bragg grating-based acoustooptic superlattice modulator. Wavelength switching of the laser emission is achieved by controlling the peak reflectivity of the different reflection bands that appear on both sides of the Bragg wavelength when a longitudinal acoustic wave propagates along the grating.     

All‐hexahedral element meshing: automatic elimination of self‐intersecting dual lines

There has been some degree of success in all‐hexahedral meshing. Standard methods start with the object geometry defined by means of an all‐quadrilateral mesh, followed by the use of the combinatorial dual to the mesh in order to define the internal connectivities among elements. For all of the known methods using the dual concept, it is necessary to first prevent or eliminate self‐intersecting (SI) dual lines of the given quadrilateral mesh. The relevant features of SI lines are studied, giving a method to remove them, which avoids deforming the original geometry. Some examples of resulting meshes are shown where the current meshing method has been successfully applied. Copyright © 2002 John Wiley & Sons, Ltd.     

An improved method for magnetic identification and localization of cracks in conductors

A SQUID magnetometer can be used to measure the magnetic field produced by flaws in a two-dimensional, conducting plate carrying a current. Identification of the flaw-induced magnetic field is difficult because of the large magnetic field associated with the edges of the plate and the current in the leads that connect the plate to the power supply. We have developed a technique by which the wire and edge fields can be cancelled prior to mapping the magnetic field. In this technique, a similar unflawed conducting sheet is placed adjacent to the flawed plate, with a connection between the sheet and the plate at one edge, and with the opposite edges of the sheet and of the plate connected to the two conductors of a coaxial cable. Thus, an applied current will flow along one conductor of the cable, across the cancelling sheet, cross into the flawed plate, return along the plate, and then return to the power supply along the other conductor of the coaxial cable. As a result of this geometry, there is no magnetic field from the lead-in wires because they are coaxial, and the magnetic field due to the edges of the plate is cancelled by the opposing magnetic field of the edges in the adjacent sheet. The extent of cancellation is determined primarily by the separation between the plate and the cancelling sheet, by the thickness of the plate, and by macroscopic inhomogeneities in their electrical conductivities.     

Optimization of the properties obtained by quenching in martensitic stainless steels X30-40Cr13 and X40-60CrMoV14

An experimental study of the effects produced by different parameters of the heat-quenching cycle permitted the optimization of the properties typical of these martensitic stainless steels: hardness and corrosion resistance. The results obtained demonstrate that the heating temperatures currently used in industrial quenching treatment of these steels should be modified.     

Attentional cues in chronic schizophrenia: Abnormal disengagement of attention.

M. I. Possner's 1980 reaction time (RT) paradigm was used to examine the engagement and disengagement operations of visual selective attention in patients with schizophrenia. In the 1st experiment 14 medicated, chronic schizophrenic Ss (diagnosed by criteria of the Diagnostic and Statistical Manual of Mental Disorders [DSM-I]), and 15 age-matched normal and control Ss made a speeded response to a target preceded by a valid, and invalid, or no cue. Control Ss showed the expected advantage and disadvantage in RT for valid and invalid cues, which suggests intact engagement and disengagement operations. For schizophrenic Ss, valid cues also enhanced RT, but invalid cues did not slow RT. Similar results were found in the 2nd experiment. The failure of unpredictable, invalid cues to inhibit RT in chronic schizophrenia may be related to an abnormality in the disengagement operation of selective attention. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Analysis of an interferometric optical fibre detection technique applied to silicon vibrating sensors

A simple and accurate analysis of a single-mode optical fibre interferometric displacement detection technique is resented. This analysis is in good agreement with experimental measurements, and shows that angular alignment between the fibre and the sensor is the most critical parameter.     

The performance of foliage mass and crown radius models in forming the input of a forest reflectance model: A test on forest growth sample plots and Landsat 7 ETM+ images

Several published foliage mass and crown radius regression models were tested on the preparation of the input for the reflectance model of Kuusk and Nilson [Kuusk, A. and Nilson, T. (2000), A directional multispectral forest reflectance model. Remote Sensing of Environment, 72(2):244–252.] for 246 forest growth sample plots in Estonia. In each test, foliage mass and crown radius for trees in the sample plots were predicted with a particular pair of allometric regression models. The forest reflectance model was then run using the estimated foliage mass and crown radius values. Reflectance factors were simulated and compared with the reflectance values obtained from three atmospherically corrected Landsat 7 Enhanced Thematic Mapper (ETM+) scenes. The statistics of linear regression between the simulated and measured reflectance factors were used to assess the performance of foliage and crown radius models. The hypothesis was that the best allometric regression models should provide the best fit in reflectance. The strongest correlation between the simulated and measured reflectance factors was found in the short-wave infrared band (ETM + 5) for all the images. The highest R² = 0.71 was observed in Picea abies dominated stands. No excellent combination of foliage mass and crown radius functions was found, but the ranking based on determination coefficients showed that some linear crown radius models are not applicable to our data. Processing of raster images, reflectance measurement for small sample plots, usage of tree-species-specific fixed parameters (specific leaf area, etc.), and the ignored influence of phenology introduced additional variation into the relationships between simulated and measured reflectance factors. Further studies are needed, but these preliminary results demonstrate that the proposed method could serve as an effective way of testing the performance of foliage mass and canopy cover regressions.