The Status of Music: A Multicolor Sub/millimeter MKID Instrument

We report on the recent progress of the Multicolor Submillimeter (kinetic) Inductance Camera, or MUSIC. MUSIC will use antenna-coupled Microwave Kinetic Inductance Detectors to observe in four colors (150 GHz, 230 GHz, 290 GHz and 350 GHz) with 2304 detectors, 576 per band, at the Caltech Submillimeter Observatory. It will deploy in 2012. Here we provide an overview of the instrument, focusing on the array design. We have also used a pathfinder demonstration instrument, DemoCam, to identify problems in advance of the deployment of MUSIC. In particular, we identified two major limiters of our sensitivity: out-of-band light directly coupling to the detectors (i.e. not through the antenna), effectively an excess load, and a large 1/f contribution from our amplifiers and electronics. We discuss the steps taken to mitigate these effects to reach background-limited performance (BLIP) in observation.     

Electrodeposition of a highly adherent and thermally stable polypyrrole coating on steel from aqueous polyphosphate solution

Electrochemical deposition of polypyrrole (PPy) on steel surface has been carried out from an aqueous polyphosphate medium using constant potential coulometry (CPC) and cyclic voltammeter (CV), and the adherence, anticorrosion property and thermal stability of the coated material have been studied.     

Solid-phase microextraction (SPME) of permethrin residues from cucumber using a silica-bonded phase-coated stainless steel fibre

Solid-phase microextraction (SPME) is a rapid, economic and solvent-free sample preparation method for the isolation of an analyte from its matrix. The technique uses a few centimetres of some adsorptive materials such as activated charcoal, polydimethylsiloxane or octadecyl silane coated onto fused silica optical fibres or, more recently, stainless steel fibres mounted into a microsyringe. The proposed method allows the extraction of permethrin from cucumber matrix into the coating, avoiding sample handling and saving evaporation of solvents and concentration steps. Adsorbed permethrin was desorbed in the split/splitless injection port of the gas chromatograph. The time required for each run was about 1.5 h, which gave a preconcentration of several orders of magnitude. The method could separate and quantify cis- and trans-isomers of permethrin. The calibration curve showed linearity in the range 1-9 μg ml^-1, with detection limits of 0.03 and 0.05 μg ml^-1 for the cis- and trans-isomers of permethrin, respectively. The method had a recovery rate of about 70% and a relative standard deviation of less than 13%. Results suggest that this procedure provides a rapid and sensitive alternative method to those currently available.     

Thermodynamic Analysis and Comparison of Performances of Air Standard Atkinson,Otto, and Diesel Cycles with Heat Transfer Considerations

This paper focuses on the overall performances of Otto, Atkinson, and Diesel air standard cycles. This study compares performance of these cycles with regard to parameters such as variable specific heat ratio, heat transfer loss, frictional loss, and internal irreversibility based on finite‐time thermodynamics. The relationship between thermal efficiency and compression ratio, and between power output and compression ratio of these cycles are obtained by numerical examples. In this study, it is assumed that during the combustion process, the heat transfer occurs only through the cylinder wall. The heat transfer is affected by the average temperature of both the cylinder wall and the working fluid. The results show that for each cycle, with the increase of the compression ratio in the specific mean piston speed, power output and thermal efficiency first increase and after reaching their maximum value, start to decrease. The results also indicate that maximum power output and maximum thermal efficiency of an Atkinson cycle could be higher than the values of these parameters in Diesel cycle and Otto cycle in the same operating conditions. The maximum power output and the maximum thermal efficiency of the Otto cycle have the lowest value among studied cycles. By increasing the mean piston speed, power output and thermal efficiency of Atkinson, Diesel, and Otto cycles start to decrease. The results of this study provide guidance for the performance analysis and show the improvement areas of practical Otto, Atkinson, and Diesel engines.     

Determination of roquefortine C in blue cheese using on-line column-switching liquid chromatography

A method is described for the determination of roquefortine C in (blue) cheese. After liquid liquid extraction with a mixture of hydrochloric acid and methanol, and filtration, an aliquot is analysed using column-switching reversed-phase liquid chromatography. The recovery of roquefortine C in Fetta cheese is about 85%, the calibration curve is linear from 10 to 2500 ng g(-1) (r2 = 0.998), and the detection limit is about 10 ng g(-1). In different batches of Danish Blue concentrations of 1000-2000 ng g(-1) of roquefortine C are found. As regards the stability of roquelfortine C its half-life in diffuse daylight is ca. 50 min, while after irradiation with ultraviolet light, it is about 10 min.     

Damping of inter-area and local modes by use of controllablecomponents

This paper deals with damping of inter-area and local electromechanical oscillation modes using controllable series capacitor (CSC) and controllable shunt capacitor (SVC). The impacts of SVC and CSC on the structure of the system closed loop matrix are investigated. By analyzing the sensitivities of the system inter-area and local modes to the control action of the controllable devices, some general conclusions concerning the damping of inter-area and local modes are made. A numerical example is provided to support the analytical findings. This paper provides an insight and understanding in the basic characteristics of damping effects of the studied devices. The insight is obtained by the study of a simple power system which exhibits both inter-area and local power swings. The understandings and findings could form the basis in analysis of realistic and more complex systems     

Combined operation of DC isolated distribution and PV systems for supplying unbalanced AC loads

This paper describes a DC isolated network which is fed by distributed generation (DG) from photovoltaic (PV) renewable sources to supply unbalanced AC loads. The battery energy storage bank has been connected to the DC network via DC/DC converter called storage converter to control the network voltage and optimize the operation of the PV generation units. The PV units are connected to the DC network via its own DC/DC converter called PV converter to ensure the required power flow. The unbalanced AC loads are connected to the DC network via its own DC/AC converter called load converter without transformer. This paper proposes a novel control strategy for storage converter which has a DC voltage droop regulator. Also a novel control system based on Clarke and Park rotating frame has been proposed for load converters. In this paper, the proposed operation method is demonstrated by simulation of power transfer between PV units, unbalanced AC loads and battery units. The simulation results based on PSCAD/EMTDC software show that DC isolated distribution system including PV units can provide the balanced voltages to supply unbalanced AC loads.     

Importance analysis considering time‐varying parameters and different perturbation occurrence times

Importance measures are integral parts of risk assessment for risk‐informed decision making. Because the parameters of a risk model, such as the component failure rates, are functions of time and a perturbation (change) in their values can occur during the mission time, time dependence must be considered in the evaluation of the importance measures. In this paper, it is shown that the change in system performance at time t, and consequently the importance of the parameters at time t, depends on the parameters perturbation time and their value functions during the system mission time. We consider a nonhomogeneous continuous time Markov model of a series‐parallel system to propose the mathematical proofs and simulations, while the ideas are also shown to be consistent with general models having nonexponential failure rates. Two new measures of importance and a simulation scheme for their computation are introduced to account for the effect of perturbation time and time‐varying parameters.