One specific class of non-linear evolution equations, known as the Tzitzéica-type equations, has received great attention from a group of researchers involved in non-linear science. In this article, new exact solutions of the Tzitzéica-type equations arising in non-linear optics, including the Tzitzéica, Dodd–Bullough–Mikhailov and Tzitzéica–Dodd–Bullough equations, are obtained using the expa function method. The integration technique actually suggests a useful and reliable method to extract new exact solutions of a wide range of non-linear evolution equations. 相似文献
In this paper, cenosphere particles embedded in AA2014 aluminium matrix are used to fabricate syntactic foam by stir casting method. The particle size is about 100?µm and foam density is about 1990?kg?m?3. Compression tests at strain rate 0.001/s are performed on foam samples to characterise their mechanical properties which are then used in numerical analysis on commercial finite element analysis software ABAQUS/CAE with isotropic elastic-plastic material model. Experimental and numerical results show good conformity in deformation behaviour with elastic and plateau zones showing average deviations less than 5% and 20%, respectively. Foams showed high yield stress and energy absorption capabilities that can be useful in making blast and impact resistant structures. 相似文献
In the present research, nanostructured Pd–Cd alloy electrocatalysts with different compositions were produced using the electrodeposition process. The morphology of the samples was studied by scanning electron microscopy analysis. Also, the elemental composition of the samples was determined by energy-dispersive X-ray spectroscopy and elemental mapping tests. Tafel polarization and electrochemical impedance spectroscopy methods were employed to determine the electrochemical corrosion properties of the synthesized samples in a solution containing 0.5 M sulfuric acid and 0.1 M formic acid. The linear sweep voltammetry, cyclic voltammetry, and chronoamperometry techniques were also employed to evaluate the electrocatalytic activity of prepared samples toward the oxidation of formic acid. In this respect, the influence of some factors such as formic acid and sulfuric acid concentrations and also potential scan rate was investigated. Compared to the pure Pd sample, the Pd–Cd samples were more reactive for the oxidation of formic acid. Besides, the sample with a lower amount of Pd (Pd1·3Cd) demonstrated much higher electrocatalytic activity than the Pd7·1Cd and Pd2·1Cd samples. The observed high mass activity of 15.06 A mg?1Pd for the Pd1·3Cd sample which is 21.1 times higher than Pd/C is an interesting result of this study. 相似文献
In this letter, we introduce and investigate a new problem referred to as the All Hops Shortest Paths (AHSP) problem. The AHSP problem involves selecting, for all hop counts, the shortest paths from a given source to any other node in a network. We derive a tight lower bound on the worst-case computational complexities of the optimal comparison-based solutions to AHSP. 相似文献
A comparative study for the nucleation of diamond was carried out using surface treatment like (i) surface scratching with
1 μm diamond paste and (ii) surface etching using chlorine plasma at different RF powers (50, 100 and 150 W). Atomic force
microscopic study shows variation in roughness from 31 nm to 110 nm. Scratching results in random scratches, whereas plasma
etches a surface uniformly. Scanning electron microscopic observations show well faceted crystallites with a predominance
of angular shaped grains corresponding to 〈100〉 and 〈110〉 crystallite surfaces for the scratched as well as plasma etched
substrate. Surface etching at 150 W plasma power results in a better growth in comparison with 50 and 100 W plasma powers.
Chlorine-radical is found responsible for the changes in the growth morphology. Raman spectroscopy shows a sharp peak at 1,332
cm−1 and a peak at ∼1,580 cm−1 for both samples. 相似文献
The influence of chloride-ion concentration on the pitting behaviour of steel in saturated Ca(OH)2 solution was studied using the D.C. polarization technique. Results seem to indicate a threshold chloride level for the on-set of severe pitting around 3000 ppm, the pitting potential Ep exhibits dramatic drop and large hysteresis loops develop. The results provide insight into the pitting performance of steel in concrete and highlight the poor repassivation of this metal/environment system. 相似文献
New experimental studies on the effects of large dynamic compressive loads on highly birefringent optical fibers are presented. The intensity rate of applied dynamic loads ranged between 2.18-6719 KN/m-sec. A Fibercore (previously York) HB600 Bow-Tie fiber with an initial beat length of 1.16 mm was employed in the present study. Sensor response is discussed in terms of the effects of force amplitudes and velocities on the calibration parameter Tf. Tf is a function of the amplitude as well as the velocity of applied loading. Therefore, calibration of the sensor should be achieved through regression analysis of the load-fringe data for the entire spectrum of the desired force velocities. The ramification of this finding is that a single experiment for the measurement of Tf cannot provide the required parameters for calibration. This further implies that the change in beat length is also dependent on the amplitude and velocity of loading. The suggested method takes both effects into account through empirical analysis of experimental data 相似文献
Most of the commonly used hydrological models do not account for the actual evapotranspiration (ETa) as a key contributor to water loss in semi-arid/arid regions. In this study, the HEC-HMS (Hydrologic Engineering Center Hydrologic Modeling System) model was calibrated, modified, and its performance in simulating runoff resulting from short-duration rainfall events was evaluated. The model modifications included integrating spatially distributed ETa, calculated using the surface energy balance system (SEBS), into the model. Evaluating the model’s performance in simulating runoff showed that the default HEC-HMS model underestimated the runoff with root mean squared error (RMSE) of 0.14 m3/s (R2?=?0.92) while incorporating SEBS ETa into the model reduced RMSE to 0.01 m3/s (R2?=?0.99). The integration of HECHMS and SEBS resulted in smaller and more realistic latent heat flux estimates translated into a lower water loss rate and a higher magnitude of runoff simulated by the HECHMS model. The difference between runoff simulations using the default and modified model translated into an average of 95,000 m3 runoff per rainfall event (equal to seasonal water requirement of ten-hectare winter wheat) that could be planned and triggered for agricultural purposes, flood harvesting, and groundwater recharge in the region. The effect of ETa on the simulated runoff volume is expected to be more pronounced during high evaporative demand periods, longer rainfall events, and larger catchments. The outcome of this study signifies the importance of implementing accurate estimates of evapotranspiration into a hydrological model.