Identification of the adverse effect of nitrate on the phosphate release rate and improvement of EBPR process models.

The adverse effect of nitrate on the phosphate release rate in the anaerobic phase was observed and was hardly explainable with conventional EBPR process models. Four possible mechanisms were proposed including substrate competition, reduced fermentation, parallel reaction and sequential reaction. Batch experiments were designed and conducted to identify the dominant mechanism. Results showed that the sequential reaction was the only possible mechanism where only denitrification occurred if any nitrate existed in the anaerobic phase. Then the phosphate release following after the nitrate was completely removed. Nitrate inhibition effect was added into the PHA storage rate to incorporate the sequential reaction in the conventional ASM3 plus EAWAG bio-P module (ASM3 + P). Nitrate inhibition coefficient, K(I,NO,PAO) was found to be as low as 0.05 mg/L. This correlated well with experimental observation where no also meant that the anaerobic compartment of a continuous flow reactor could be seriously affected by the residual nitrate contained in the sludge recycle flow. This phenomenon caused overestimation of the phosphate uptake rate and consequently underestimation of PO4(3-) -P concentration. This problem was resolved by incorporation of a nitrate inhibition term in the ASM3 + P for more accurate simulation of the EBPR process.     

Spectral shape tunable band-rejection filter using a long-period fiber grating with divided coil heaters

We have developed a new type of tunable band rejection filter, which provides high spectral-shaping flexibility in a wide tuning range. The filter consists of a long-period fiber grating (LPFG) with divided coil heaters. Each of the divided coil heaters is controlled individually to adjust a temperature distribution along the LPFG and to modify the spectral shape of the LPFG filter. The tunable band rejection filter is demonstrated to function properly when applied as an erbium-doped fiber amplifier gain-flattening filter.     

Reducing cycle times in manufacturing and supply chains by input and service rate smoothing

A key performance parameter of a manufacturing network or supply chain is its cycle time; the time that a typical item spends in the network. A previous simulation study on a semiconductor assembly and test facility showed that cycle times could be reduced by having smooth input and service rates. This suggested that there is a “cycle time principle” that, for a system with a specified throughput or input rate, the shortest cycle times are obtained when the input and service rates do not vary over time. We prove that this principle is true for the M/G/1 and M/M/s queueing systems and Jackson networks. The analysis involves establishing several results on the concavity of waiting time probabilities and the convexity of expected waiting times and queue lengths, as functions of input and service rates. These results also have natural uses in other optimization problems.     

Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003     

A study of CaCO3 fouling with a microscopic imaging technique

The present study introduces a new experimental method to visualize the fouling process of CaCO₃. A mini-channel heat exchanger system with a microscopic imaging technique was developed for real-time visualization of the fouling process. The present study discussed how scale started initially, how scale formed thick layers, and how a small crystal grew into a large one, touching the adjacent one. Detail microscopic images of scale crystals and corresponding fouling resistances were obtained over the entire fouling process. The microscopic observation indicated that the fouling process could be divided into three stages: an induction period, a period of uniform generation of nuclei, and a period of uniform growth of scale. Sudden appearance of numerous small nuclei indicated the end of the induction period, a key event before the rapid increase in the fouling resistance. The present experimental method using microscopic images of the wet fouling process provides a valuable insight on the fouling mechanism.     

Facile modifications of polyimide via chloromethylation: II. Synthesis and characterization of thermocurable transparent polyimide having methylene acrylate side groups

From chloromethylated polyimide, a useful starting material for modification of aromatic polyimides, a thermocurable transparent polyimide having acrylate side groups was prepared. In the presence of 1,8‐diazabicyclo[5,4,0]undec‐7‐ene, chloromethylated polyimide was esterified with acrylic acid to synthesize poly(imide methylene acrylate). The polymer was soluble in organic solvent, which makes it possible to prepare a planar film by spin coating. The polymer film became insoluble after thermal treatment at 230 °C for 30 min. Optical transparency of the film at 400 nm (for 1 µm thickness) was higher than 98 % and not affected by further heating at 230 °C for 250 min. Adhesion properties measured by the ASTM D3359‐B method ranged from 4B to 5B. Preliminary results of planarization testing showed a high degree of planarization (DOP) value (>0.53). These properties demonstrate that poly(imide methylene acrylate) could be utilized as a thermocurable transparent material in fabricating display devices such as TFT‐LCD. Copyright © 2004 Society of Chemical Industry     

A simple mathematical analysis on the effect of sand in Cr(VI) reduction using zero valent iron

A simple mathematical model was proposed to analyze the enhancement of Cr(VI) reduction when sand materials are added to the zero valent iron (ZVI). Natural decay of Cr(VI) in a control experiment was analyzed by using a zero-order decay reaction. Adsorption kinetics of Cr(VI) to sand was modeled as a first-order reversible process, and the reduction rate by ZVI was treated as a first-order reaction. Natural decay of Cr(VI) was also included in other experiments, i.e., the adsorption to sand, the reduction by ZVI, and both adsorption and reduction when sand and ZVI are present together. The model parameters were estimated by fitting the solution of each model to the corresponding experimental data. To observe the effect of sand addition to ZVI, both adsorption and reduction rate models were considered simultaneously including the natural decay. The solution of the combined model was fitted to the experimental data to determine the first-order adsorption and reduction rate constants when sand as well as ZVI is present. The first-order reduction rate constant in the presence of sand was about 35 times higher than that with ZVI only.     

Distributed self-stabilizing placement of replicated resources in emerging networks

Emerging large scale distributed networking systems, such as P2P file sharing systems, sensor networks, and ad hoc wireless networks, require replication of content, functionality, or configuration to enact or optimize communication tasks. The placement of these replicated resources can significantly impact performance. We present a novel self-stabilizing, fully distributed, asynchronous, scalable protocol that can be used to place replicated resources such that each node is "close" to some copy of any object. We describe our protocol in the context of a graph with colored nodes, where a node's color indicates the replica/task that it is assigned. Our combination of theoretical results and simulation prove stabilization of the protocol, and evaluate its performance in the context of convergence time, message transmissions, and color distance. Our results show that the protocol generates colorings that are close to the optimal under a set of metrics, making such a protocol ideal for emerging networking systems.     

Onset of buoyancy-driven convection in melting from below

When a horizontal homogeneous solid is melted from below, convection can be induced in a thermally unstable melt layer. In this study the onset of buoyancy-driven convection during time-dependent melting is investigated by using similarly transformed disturbance equations. The critical Rayleigh numbers based on the melt-layer thickness are found numerically for various conditions. For small superheats, the present predictions approach the well known results of classical Rayleigh-Bénard problems, that is, critical Rayleigh numbers are located between 1,296 and 1,708, regardless of the Prandtl number. However, for high superheats the critical Rayleigh number increases with an increase in phase change rate but with decrease in Prandtl number.