Effects of Winding Attachment Positions on Output Characteristics of Flux‐Modulating Synchronous Machines

The flux‐modulating synchronous machine (FMSM) is a new type of multipole SM with nonoverlapping concentrated armature and field windings on the stator. This paper compares the output characteristics of two FMSMs through finite element analysis (FEA) and experiments. In both of the FMSMs, the attachment positions of the armature and field windings are swapped. To determine the reason for the discrepancies in their output characteristics, unsaturated inductances were calculated using a d‐‐q equivalent circuit. In addition, the calculated results of the inductances were confirmed through a visualization of the leakage fluxes using FEA. The results of the study show that the synchronous inductance can be reduced by attaching the armature winding to the air‐gap side of the stator teeth and that the reduction leads to an increase in output power.     

A comparative study of DPSK and OOK WDM transmission over transoceanic distances and their performance degradations due to nonlinear phase noise

We have compared experimentally the transmission performance of return-to-zero differential phase-shift keying (RZ-DPSK) with RZ-ON-OFF keying (OOK), nonreturn-to-zero differential phase-shift keying (NRZ-DPSK), and NRZ-OOK for 100/spl times/10-Gb/s transmission with a spectral efficiency of 0.22 b/s/Hz over transoceanic distances. The Q degradation of the RZ-DPSK after transmission over 9180 km was 3 dB greater than that of RZ-OOK. The experimental results clearly showed the major cause of degradation for DPSK is not cross-phase modulation but self-phase modulation. The calculated nonlinear phase noise, i.e., the Gordon-Mollenauer effect, agreed with the experimental results. A distributed-Raman-amplifier assisted erbium-doped-fiber-amplified transmission line acted well in reducing the nonlinear phase noise.     

Solution intercalation of polystyrene and the comparison with poly(ethyl methacrylate)

Polystyrene nanocomposites have been prepared via solution intercalation method. Combination of wide-angle X-ray diffraction and thermogravimetric analysis is used to study the effect of solvents on the morphology of the nanocomposites as a function of the amount of residual solvent. d-Spacing of the polystyrene nanocomposites has a minimum value when the residual solvent concentration is between 2 and 4 wt%. Different interaction level between the solvent molecules and polymer chains is considered to be the reason for this special d-spacing change behavior. By comparing the solution intercalation of polystyrene and poly(ethyl methacrylate) from different solvents, it is concluded that the interactions between polymer-surfactant, solvent-surfactant, and polymer-solvent play important role for the solution intercalation of polymers.     

Suppression control method for torque vibration of three-phase HB-type stepping motor utilizing feedforward control

This paper proposes a method to reduce the vibration of the three-phase HB-type stepping motor with cogging torque by the feedforward compensation control. The compensation signal to suppress the vibration of the motor frame is obtained by the repetitive controller installing an online Fourier transformer and utilizing an acceleration sensor attached to the motor frame or an acoustic sensor such as a microphone placed close to the frame. The sensor is used only for the acquisition of the feedforward compensation data. The feedforward compensation signal at an arbitrary operating point is derived from the amplitude and phase data of the frequency components and the operating point data. Compensation data obtained by the repetitive controller is applied to the operating point changed by reference frequency and load condition in steady state. The compensation signal for the new operating point will be generated from compensation data utilizing polynomial equation approximation and linear interpolation method. The effectiveness of this proposed method is confirmed by the experimental results.     

Digitally tunable optical filters using arrayed-waveguide grating(AWG) multiplexers and optical switches

Two novel configurations for digitally tunable optical filters based on arrayed-waveguide grating (AWG) multiplexers are described in detail with emphasis on the connection of the AWG multiplexer and optical switches. Performance comparisons show that conventional configurations are disadvantaged by the switch size required and loss imbalance among the optical frequency-division-multiplexed (FDM) channels; the proposed configurations require only O(√(N)) switch elements to select one of N FDM channels, and the loss imbalance is lower by up to 75% in decibel     

Tuning-current splitting network for three-section DBR lasers

A simple current-splitting network for DBR-laser frequency tuning is proposed that distributes a single control current among two tuning sections and can adjust the current distribution without yielding impedance mismatching. The nonlinear characteristics of the tuning sections realise the non-proportional current splitting suitable for continuous tuning; 470 GHz (3.8 nm) tuning range is achieved     

Continuous hydrolysis of olive oil by lipase in microporous hydrophobic membrane bioreactor

Continuous hydrolysis of olive oil byCandida cylindracea’s lipase was studied in a microporous hydrophobic membrane bioreactor. Olive oil and buffer solution, fed continuously through two compartments partitioned by membrane, caused reaction at the interface of lipase-adsorbed membrane and buffer solution. Fatty acid was obtained in a single phase without being mixed with components of other phases. At all mean residence times, countercurrent flow mode was superior to cocurrent one. The lipase was adsorbed onto the membrane, and its adsorption was suggested to be partially specific from the experiments with enzymes having various levels of purity. The percent hydrolysis depended hyperbolically on the interfacial enzyme concentration. The hydrolysis seemed to be limited by diffusion of fat or fatty acid through the micropores of the membrane at higher interfacial enzyme concentrations. The lipase was stabilized significantly by glycerol added to the buffer solution. Satisfactory performance of the membrane bioreactor was obtained in a longterm continuous operation which lasted for 24 days by feeding buffer-glycerol (18.0%) solution over the adsorbed lipase. The operational half-life of the adsorbed enzyme was 15 days at 40 C.     

Preparation of one-dimensional polymer films by modification of a hydroxymethylbenzene self-assembled monolayer on iron with alkyltriethoxysilanes for preventing iron corrosion

A self-assembled monolayer (SAM) of p-hydroxymethylbenzene HOCH₂C₆H₄ - (HOMB) moiety adsorbed on iron by the formation of a covalent bond between carbon and iron atoms was prepared by electrochemical derivatization of an iron electrode with p-hydroxymethylbenzenediazonium tetrafluoroborate HOCH₂C₆H₄N₂BF₄. The electrode covered with the HOMB SAM was modified with alkyltriethoxysilanes C_nH_2n+1Si(OC₂H₅)₃ (C_nTES, n = 8 or 18) to prepare a film of one-dimensional polymer. The protective ability of the polymer film was determined by polarization measurement of the covered electrode in an aerated 0.5 M NaCl solution. The ability was enhanced by modification of the HOMB SAM with C_nTES markedly. The iron surface coated with the one-dimensional polymer film of the HOMB SAM modified with C₈TES was characterized by contact angle measurement and FTIR reflection and X-ray photoelectron spectroscopies. The persistence in the protective ability of the polymer film against iron corrosion in 0.5 M NaCl may be associated with the strong adsorption via the covalent bond, revealed by electron-probe microanalysis.     

Direct digital design of computed torque controllers

Direct digital design of computed torque controllers for a robot manipulator is discussed in this article. A simple discrete-time model of the robot manipulator obtained by Euler's method is used for the design. Taking account of computation delay in the digital processor, we propose predictor-based designs of the PD and PID type controllers. The PID-type controller is designed based on a modified version of the discrete-time integral controller proposed by Mita. For both controllers, the feedback gains can be determined easily by using simple formulas. A simulation example is presented to illustrate the relevance of the proposed designs and the robustness of PID-type controller against physical parameter variations. © 1994 John Wiley & Sons, Inc.