Transient liquid phase sintering of high-purity mullite for high-temperature structural ceramics

High-purity mullite ceramics, promising engineering ceramics for high-temperature applications, were fabricated using transient liquid phase sintering to improve their high-temperature mechanical properties. Small amounts of ultrafine alumina or silica powders were uniformly mixed with the mullite precursor depending on the silica-alumina ratio of the resulting ceramics to allow for the formation of a transient liquid phase during sintering, thus, enhancing densification at the early stage of sintering and mullite formation by the reaction between additional alumina and the residual glassy phase (mullitization) at the final stage of sintering. The addition of alumina powder to the silica-rich mullite precursor resulted in a reaction between the glassy silica and alumina phases during sintering, thereby forming a mullite phase without inhibiting densification. The addition of fine silica powder to the mullite single-phase precursor led to densification with an abnormal grain growth of mullite, whereas some of the added silica remained as a glassy phase after sintering. The resulting mullite ceramics prepared using different powder compositions showed different sintering behaviors, depending on the amount of alumina added. Upon selecting an optimum process and the amount of alumina to be added, the pure mullite ceramics obtained via transient liquid phase sintering exhibited high density (approximately 99%) and excellent high-temperature flexural strength (approximately 320 MPa) at 1500 °C in air. These results clearly demonstrate that pure mullite ceramics fabricated via transient liquid phase sintering with compositions close to those of stoichiometric mullite could be a promising process for the fabrication of high-temperature structural ceramics used in an ambient atmosphere. The transient liquid phase sintering process proposed in this study could be a powerful processing tool that allows for the preparation of superior high-temperature structural ceramics used in the ambient processing atmosphere.     

Re-evaluation of Radiation-Energy Transfer to an Extraction Solvent in a Minor-Actinide-Separation Process Based on Consideration of Radiation Permeability

ABSTRACT

Absorbed-dose estimation is essential for evaluation of the radiation tolerance of minor-actinide-separation processes. We propose a dose-evaluation method based on radiation permeability, with comparisons of heterogeneous structures seen in the solvent-extraction process, such as emulsions forming in the mixture of the organic and aqueous phases. A demonstration of radiation-energy-transfer simulation is performed with a focus on the minor-actinide-recovery process from high-level liquid waste with the aid of the Monte Carlo radiation-transport code PHITS. The simulation results indicate that the dose absorbed by the extraction solvent from alpha radiation depends upon the emulsion structure, and that from beta and gamma radiation depends upon the mixer-settler-apparatus size. Non-negligible contributions of well-permeable gamma rays were indicated in terms of the plant operation of the minor-actinide-separation process.     

Mass transfer in polycrystalline ytterbium monosilicate under oxygen potential gradients at high temperatures

Mass transfer in polycrystalline Yb₂SiO₅ wafers with precise composition control was evaluated and analyzed by oxygen permeation experiments at high temperatures using an oxygen tracer. Oxygen permeation proceeded due to mutual grain boundary diffusion of oxide ions and Yb ions without synergistic effects such as acceleration or suppression. The oxygen shielding properties of Yb₂SiO₅ were compared with those of the other line compounds such as Yb₂Si₂O₇ and Al₂O₃ based on the determined mass transfer parameters. It was found that the more preferentially an oxide ion diffuses in the grain boundary compared to the interior of the grain, the greater the effect of suppressing the movement of the oxide ion by applying an oxygen potential gradient becomes.     

Radiophotoluminescence phenomenon in copper-doped aluminoborosilicate glass

Radiophotoluminescence phenomena have been widely investigated on various types of materials for dosimetry applications. We report that an aluminoborosilicate glass containing 0.005 mol% copper exhibits intense photoluminescence in the visible region induced by X-ray and γ-ray irradiation. The luminescence is assigned to the 3d⁹4s¹ → 3d¹⁰ transition of Cu⁺. The proportionality of the intensity of the induced photoluminescence to the irradiation dose was confirmed up to 0.5 kGy using ⁶⁰Co γ-ray irradiation. Based on the spectroscopic results, a potential mechanism was proposed for the enhancement of the photoluminescence. The exposure to the ionizing radiation generates electron-hole pairs in the glass, and the electrons are subsequently captured by the Cu²⁺ ions, which are converted to Cu⁺ and emit the luminescence. For the glass containing 0.01 mol% copper, the pronounced enhancement of the photoluminescence was not observed because the reverse reaction, ie, the capture of the holes by the Cu⁺ ions, becomes prominent. The photoluminescence induced by the irradiation was stably observed for the glasses kept at room temperature and even for the glasses heat-treated at 150°C. However, the induced photoluminescence could be eliminated by the heat treatment at a temperature at 500°C, and the glass returned to the initial pre-irradiation state. The Cu-doped aluminoborosilicate glass is a potential candidate for use in dosimetry applications.     

Supramolecular Zn(II)-Dipicolylamine-Azobenzene-Aminocyclodextrin-ATP Complex: Design and ATP Recognition in Water

Cyclodextrins (CyDs) are water-soluble host molecules possessing a nanosized hydrophobic cavity. In the realm of molecular recognition, this cavity is used not only as a recognition site but also as a reaction medium, where a hydrophobic sensor recognizes a guest molecule. Based on the latter concept, we have designed a novel supramolecular sensing system composed of Zn(II)-dipicolylamine metal complex-based azobenzene (1-Zn) and 3A-amino-3A-deoxy-(2AS,3AS)-γ-cyclodextrin (3-NH₂-γ-CyD) for sensing adenosine-5′-triphosphate (ATP). 1-Zn showed redshifts in the UV-Vis spectra and induced circular dichroism (ICD) only when both ATP and 3-NH₂-γ-CyD were present. Calculations of equilibrium constants indicated that the amino group of 3-NH₂-γ-CyD was involved in the formation of supramolecular 1-Zn/3-NH₂-γ-CyD/ATP. The Job plot of the ICD spectral response revealed that the stoichiometry of 1-Zn/3-NH₂-γ-CyD/ATP was 2:1:1. The pH effect was examined and 1-Zn/3-NH₂-γ-CyD/ATP was most stable in the neutral condition. The NOESY spectrum suggested the localization of 1-Zn in the 3-NH₂-γ-CyD cavity. Based on the obtained results, the metal coordination interaction of 1-Zn and the electrostatic interaction of 3-NH₂-γ-CyD were found to take place for ATP recognition. The “reaction medium approach” enabled us to develop a supramolecular sensing system that undergoes multi-point interactions in water. This study is the first step in the design of a selective sensing system based on a good understanding of supramolecular structures.     

Eu@C86 isomers: Calculated relative populations

Abstract

Relative populations of four energy-lowest IPR (isolated-pentagon-rule) isomers of Eu@C₈₆ are computed using the Gibbs energy based on characteristics from density functional theory calculations (M06-2X/3-21G?～?SDD entropy term, M06-2X/6-31G*～SDD or B2PLYP(D)/6-31G*～SDD energetics). The calculations confirm that the recently isolated Eu@C₁(7)-C₈₆ species is a major isomer in a relevant temperature region. Relationship to the empty C₈₆ cages is discussed, too.     

Cover Image,Volume 69, Issue 3

The cover image is based on the Mini‐Review Well‐defined, environment‐friendly synthesis of polypeptides based on phosgene‐free transformation of amino acids into urethane derivatives and their applications by Takeshi Endo et al., https://doi.org/10.1002/pi.5952 . Cover image © Takeshi Endo Images.

     

EFFECT OF DEVELOPER PROPERTIES ON PRINT QUALITY

We investigated the dependence of the toner charge-to-mass ratio (q/m) in a two-component electrophotographic developer on the shaking time, toner concentration (T/C), carrier sizes, and the carrier core and the coating materials, as well as the resulting print qualities in terms of print density, background density, tone reproduction, resolution, and dot gain. Four different sizes of spherical ferrite carriers, four different carrier coating materials, and an irregular iron carrier were used with two types of toner: 14 um red toner (NP-4080) and 8 um cyan toner (CLC-500). The q/m measurement by the blow-off method showed that the red toner charge was positive while the cyan toner charge was negative with these carriers. The toner q/m values, which depended on the shaking time and decreased with the increasing T/C were much more affected by the larger carrier and the smaller toner. The carriers which yielded charges in the proper range produced better print qualities than did the other carriers that yielded a toner q/m     

Capacity enhancement of cellular CDMA by traffic-based control ofspeech bit rate

Variable rate speech coding is now recognized as an important system component for high-capacity cellular networks because it exploits speech statistics to reduce the average bit rate, which results in reduced interference and increased capacity. Once a variable rate capability is available, an additional capacity enhancement can be achieved by introducing network control of the user bit rate in response to changing traffic levels. We introduce the concept of network control of rate and propose a particular network-control method for code-division multiple access (CDMA) systems. Based on an M/M/∞//M queueing model applied to a cell under heavy traffic conditions and a new performance measure called averaged speech quality, we obtain simulation results to demonstrate how network control of rate can achieve improved speech quality or increased capacity for a given quality objective