Syntheses and structural properties of four Rb-aluminosilicate zeolites

Four types of Rb-aluminosilicate zeolites were hydrothermally synthesized in pure phase for the first time from Rb-aluminosilicate gels without using any organic structure-directing agent (SDA) under stirring conditions. The crystal structure of each zeolite was refined by Rietveld analysis of the X-ray diffraction (XRD) data. These crystal structures were confirmed to be Rb-mordenite, Rb-merlinoite, a new aluminosilicate zeolite with an ATT framework topology, and Rb-offretite denoted by RMA-1, RMA-2, RMA-3, and RMA-4, respectively. The Si/Al ratio of RMA-1 with an MOR topology varied from 5.3 to 8.0; however, the variation of the Si/Al ratios of the other zeolites was rather small. The crystal system of RMA-2 was tetragonal with space group I4/mmm, where two Rb sites were distributed at the center of an 8-membered ring (MR). On the other hand, two Rb sites in RMA-3 were located at the center of the 8-MR in small two cages. The structure of RMA-4 was identified as the OFF type with a local disorder or defect, which included a small amount of an intergrown ERI phase.     

The distribution of soap in the polymerization system for preparation of carboxylated polystyrene latexes

The distribution of soap in the polymerization system for preparation of carboxylated polystyrene latexes has been investigated. The critical micelle concentration (CMC) for sodium dodecyl sulfate (SDS) in the polymerization system was determined by surface tension measurement to be 0.173 mmole/l. The solubility of styrene (St) in the aqueous phase of the polymerization system was determined by NMR measurement to be 4.52 mmole/l. It was confirmed by NMR measurement that at the concentration of SDS higher than the CMC, St is solubilized in the interior of the SDS micelles, and the concentration of solubilized St is almost proportional to the concentration of micellar SDS. From this relationship, the number and radius of SDS micelles containing solubilized St can be determined.     

A full‐color eyewear display using planar waveguides with reflection volume holograms

Abstract— A full‐color eyewear display with over 85% see‐through transmittance with a 16° horizontal field of view was developed. Very low color crosstalk, less than 0.008 Δu′v′ uniformity, and 120% NTSC color gamut were achieved. Waveguides with two in‐ and out‐coupling reflection volume hologram elements enabled a simple configuration that has an optical engine beside the user's temples. The reflection volume hologram elements used on the waveguides realized a small thickness of 1.4 mm for each waveguide, and an out‐coupling reflection volume hologram used as an optical combiner contributed a high see‐through transmittance of 85% due to its wavelength selectivity. However, there are technical challenges in achieving a reasonable screen size and quality color images with optics that utilize holographic waveguides because holograms have large chromatic dispersions compared to conventional optical elements such as lenses and mirrors. Approaches to overcome these issues are described.     

Application results of a prototype ultrasonic liquid film sensor to a 7 MPa steam–water two-phase flow experiment

A prototype ultrasonic liquid film sensor was applied to a high-temperature steam–water two-phase flow experiment. The liquid film sensor was vertically installed in a loop which was connected to HUSTLE, a multi-purpose steam source test facility. The hydraulic diameter of the measurement section was 9.4 mm. The output waveforms of the sensor were acquired with a digital oscilloscope. The fluid temperature and system pressure were kept at 288 °C and 7.2 MPa, respectively, during the experiment. The pulse-echo method was used to calculate the liquid film thickness. The cross-correlation calculation was utilized to determine the time difference between the pulse reflected at the sensor surface and the pulse reflected at the liquid film surface. The time-averaged liquid film thicknesses were less than 0.055 mm in the annular flow condition. The increase of the time-averaged thickness was small with the change of the gas momentum flux. The film thicknesses measured with the sensor were compared with the past experimental results; the former were smaller than one-fourth of the thickness estimated as the mean film thickness. The comparison results suggested that the continuous liquid sublayer thickness was measured with the liquid film sensor.     

Biosynthesis of Trehangelin in Polymorphospora rubra K07–0510: Identification of Metabolic Pathway to Angelyl‐CoA

Trehangelins are trehalose angelates discovered from endophytic actinomycete Polymorphospora rubra K07‐0510. We identified the trehangelin biosynthetic gene cluster, including genes that encode a glycoside hydrolase‐like protein (thgC), α‐amylase (thgD), 3‐ketoacyl‐ACP synthase III (thgI), 3‐ketoacyl‐ACP reductase (thgK), enoyl‐CoA hydratase (thgH) and acyl transferase (thgJ). Heterologous expression of thgH, thgI, thgJ and thgK confirmed the importance of these genes in the biosynthesis of trehangelin A. Enzymatic activity studies showed that ThgI catalyses the condensation of acetyl‐CoA and methylmalonyl‐CoA to 2‐methylacetoacetyl‐CoA (MAA‐CoA), ThgK catalyses NADPH‐dependent reduction of MAA‐CoA to 3‐hydroxy‐2‐methylbutyryl‐CoA (HMB‐CoA) and ThgH catalyses the dehydration of HMB‐CoA to angelyl‐CoA (AN‐CoA). This is the first report on the elucidation of the enzymatic formation of AN‐CoA.     

Yield of OH radicals in water under heavy ion irradiation. Dependence on mass, specific energy, and elapsed time

Dependence of yields of OH （hydroxyl） radicals on the mass and specific energy of heavy ions and elapsed time after irradiation was investigated, to understand chemical reactions of aqueous solutions. The yields of irradiation products of phenol, super-linearly increased with the incident energy of He, C, and Ne ions ranging from 2 to 18 MeV/u. The yields of the OH radicals were estimated by analyzing the yields of the irradiation products of phenol. The yields of the OH radicals increased with the specific energy for each ion, but decreased both with the mass of each ion at the same specific energy and elapsed time after irradiation.     

Application of electron beam for the reduction of PCDD/F emission from municipal solid waste incinerators

The electron-beam technology was applied to reduce the emission of polychlorinated dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF) in a flue gas of 1000 m(3)N/h from the municipal solid waste incinerator (MSWI) at a temperature of 200 degrees C. More than 90% decomposition of PCDD/Fs was obtained using an electron accelerator at a dose of 14 kGy. The decomposition was initiated through reactions with OH radicals produced by the irradiation of flue gases, followed by oxidation such as the ring cleavage of the aromatic ring, the dissociation of ether bond, and dechlorination. The cost analysis estimated that the electron-beam system can cut the annualized cost by approximately 50% for the treatment of PCDD/Fs in a pre-dusted MSWI flue gas as compared with a bag-filter system when operating on electricity generated from an incineration. Electron-beam technology is an economically and technologically useful method for reducing PCDD/Fs in an incineration flue gas.     

Experiments and simulations of uniaxial ratchetting deformation of Sn–3Ag–0.5Cu and Sn–37Pb solder alloys

This paper discusses uniaxial ratchetting deformation of lead-free solder alloy Sn–3Ag–0.5Cu and lead-containing solder alloy Sn–37Pb, which were subjected to tension–compression loading with several stress amplitudes and stress ratios, minimum stress over maximum stress. First the uniaxial ratchetting tests were conducted with three maximum stresses and four stress ratios. All tests were conducted using cylindrical bulk specimens of the solder alloys at 313 K. The test results show that there are differences in the ratchetting deformation behavior of the two solder alloys; the larger ratchetting strain occurs in the lead-containing solder alloy than in the lead-free solder alloy. The ratchetting deformation was simulated by the dislocation based constitutive model proposed by Estrin et al. (J Eng Mater Technol 118:441, 1996). The evolution equation of the back stress employed in the constitutive model was modified considering a dynamic recovery term. The effect of the modification of the back stress evolution is discussed by comparing the simulations with the corresponding experimental results. The simulations suggest that the recovery term in the kinematic hardening rule plays an important role in fitting the simulation to the experimental results of the ratchetting deformation of the solder alloys.     

EFFECT OF DRYING METHOD ON MESOPOROSITY OF RESORCINOL-FORMALDEHYDE DRYGEL AND CARBON GEL

Resorcinol-formaldehyde hydrogels were synthesized by sol-gel polycondensation of resorcinol with formaldehyde in a slightly basic aqueous solution. RF cryogels, RF xerogels, and RF xerogels (MW gels) were respectively prepared from RF hydrogels by freeze drying, hot air drying, and microwave drying. Carbon cryogels, carbon xerogels and carbon MW gels were subsequently obtained by pyrolyzing RF drygels in an inert atmosphere. Freeze drying and microwave drying were effective to prepare mesoporous RF drygels and carbon gels. RF cryogels and carbon cryogels showed high mesoporosity over wide ranges of the molar ratio of resorcinol to catalyst (R/C) and the ratio of resorcinol to water (R/W) used in sol-gel polycondensation. Although RF xerogels had a few mesopores, carbon xerogels had no mesopores. RF MW gels and carbon MW gels showed mesoporosity if appropriate values of R/C and R/W were selected.     

东丽的环境挑战及新材料

东丽以"Innovation by Chemistry"为核心,通过融合有机化学、高分子科学、生物化学、纳米技术等进行技术革新,挑战具有创新意义的新素材及新技术,为全球用户创造新的价值,致力于改善地球环境,技术创新开发。东丽纤维研究所(中国)有限公司成立于2002年5月,与日本东丽株式会社共同致力于中国的纤维及高分子材料的研究。设有南通总公司和上海分公司,本次就公司的研究开发概要作报告。着重报告东丽(株)正在推进的环境友好型新材料研究开发状况。包括生物基聚合物聚乳酸、PTT、生物尼龙等相关的技术概要及特征。另外介绍一下具有环境保护技术的绿色工艺的纤维素纤维。