Fabrication of lotus-type porous carbon steel by the continuous zone melting method and its mechanical properties

A lotus-type porous carbon steel with cylindrical pores was fabricated by the continuous zone melting method in a pressurized mixture of hydrogen and helium gases. The porosity increases with increasing partial pressure of the hydrogen gas, while the pore diameter remains almost constant, independent of the pressure. The ultimate tensile strength of the specimen with cylindrical pores parallel to the tensile direction is lower than the estimated value, assuming that the strength is decreased in proportion to the decrease of the cross-sectional area of the specimen, while the yield strength is higher than the estimated value. The compressive yield strength is also higher than the estimated value. The increase in yield strength is considered to be due to precipitation strengthening. The tensile strength is increased by quenching and tempering, while the elongation decreases. Such mechanical properties are discussed in terms of the microstructural analysis.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

Feedback control of decoupled bending and torsional vibrations of flexible beams

In this article, we consider a flexible beam with a rigid body, of which the bending vibration and the torsional vibration are decoupled. Therefore we need two control motors to suppress the vibrations. Each set of dynamic equations is treated in the form of an appropriate Hilbert space. A stabilizing feedback control law of each rotation motor will be established on the basis of modal analysis. A set of experiments has been carried out, and the results demonstrate the effectiveness of the dynamic model and the proposed control law. © 1994 John Wiley & Sons, Inc.     

High-efficiency finishing process for metal mold by large-area electron beam irradiation

A new finishing process for metal molds by large-area electron beam (EB) irradiation is proposed in this study. In the large-area EB irradiation equipment used here, an EB with high-energy density is irradiated without focusing the beam, and so the EB with a maximum diameter of 60 mm can be used for melting or evaporating metal surface instantly. Experimental results show that the surface roughness decreases from 6 μmRz to less than 1 μmRz in just a few minutes under proper machining conditions. The corrosion resistance of metal mold surface also could be greatly improved by large-area EB irradiation. Furthermore, the surface roughness of tilting surface close to 90° could be well improved. Therefore, large-area EB irradiation method has a possibility to become a high-efficiency finishing process for metal molds.     

Intramolecular triplet energy migration in poly(2-vinylnaphthalene) and poly(naphthylalkyl methacrylate)s in solid solution: Effects of side chain length

Summary The effect of side chain length on intramolecular triplet energy migration of naphthalene containing polymers was investigated by a delayed fluorescence (DF) spectroscopy for the solid solution of the polymers. The degree of triplet energy migration depends strongly on whether the chromophores are directly attached to the main chain or not.     

Deposition of carbon films by electrolysis of a water-ethylene glycol solution

An attempt was made to deposit carbon films by electrolysis of a water-ethylene glycol solution. Carbon plate and an n-type silicon substrate were dipped in the solution and a high d.c. potential was negatively applied on the silicon substrate. Some deposits were observed in the region between the boiling point curve and the line approximately 50 °C below and parallel to the boiling point, when electrolysis was carried out at 1 kV for 6 h. For higher potentials of 1.4–2.0 kV and longer electrolysis of 12 h, some samples showed a broad X-ray diffraction peak and Raman peaks, corresponding to graphitic carbon.     

A novel method of suppressing the inrush current of transformers by using a series‐connected voltage‐source PWM converter

This paper proposes a novel method of suppressing the inrush current of transformers. A small‐rated voltage‐source PWM converter is connected in series to the transformers through a matching transformer. As the connected PWM converter serves as a resistor for the source current, no inrush phenomena occurs. The required rating of the PWM converter, which serves as the damping resistor for the inrush phenomena, is 1/400 that of the main transformers in single‐phase circuits. In three‐phase circuits, it is 1/900. The basic principle of the proposed method is discussed. Digital computer simulation is implemented to confirm the validity and excellent practicability of the proposed method using the PSCAD/EMTDC. A prototype experimental model is constructed and tested. The experimental results demonstrate that the proposed method can perfectly suppress the inrush phenomena. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 157(4): 56–65, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20174     

Optical data storage by novel photoelectrochromic polymer

A novel elastic polymer containing 4,4′-bipyridinium salts with tetrakis[3,5-bis(trifluoromethyl)phenyl]borate as part of the main chain was synthesized. The cast film showed persistent and reversible colour changes due to photoinduced electron transfer upon excitation of an ion-pair charge-transfer band (_ex >365 nm) in vacuo. The lifetime of the coloured state markedly depended on temperature. The optically written data were stored without decay below 0°C and were erased thermally at elevated temperatures. The colour changes were reversibly repeatable for many times.     

Lipid-Lowering Effect of Eriocitrin, the Main Flavonoid in Lemon Fruit, in Rats on a High-Fat and High-Cholesterol Diet

ABSTRACT:  Eriocitrin (eriodictyol 7- O -β-rutinoside) is the main flavonoid in lemon fruit. In this study, eriocitrin was investigated for its lowering effect on serum and hepatic lipids in high-fat and high-cholesterol fed rats. Rats in the control group ( N = 6) were fed a 20% lard and 1% cholesterol diet for 21 d, and rats in the 0.35% eriocitrin group ( N = 6) and 0.70% eriocitrin group ( N = 6) were fed a diet supplemented with eriocitrin 0.35% and 0.70%, respectively. The content of hepatic total cholesterol and triglyceride in the eriocitrin group was no different from that of the control group. The total cholesterol, VLDL+LDL, triglyceride, and phospholipid in the serum of the 0.35% eriocitrin group showed significantly lower concentrations than the control group ( P < 0.05), although there was no difference in the HDL concentrations among the groups. The lowering effect of eriocitrin for serum total cholesterol was thought to be caused by a decrease in VLDL+LDL. The 0.35% eriocitrin group was shown to have a significant increase in excretion of fecal bile acid ( P < 0.05) and a tendency for enhanced hepatic m-RNA levels of LDL receptor in comparison with the control group.