常温挤出糖霜3D打印机设计

目的:设计一款满足安全、卫生、操作便捷、结构性能稳定等要求的糖霜制品3D打印机.方法:打印机主要包括机械结构和控制系统,机械结构方面采用龙门架结构,并对传统的打印料罐进行改良.控制系统采用“工控机+运动控制卡”的模式.结果:该打印机可快速更换料罐(30s内),打印机成型速度快(≥5000mm/min),速度可调;成型精度控制在1mm 以内;成型件的强度、膨胀率和表面粗糙度指标均较好.自带光源的图像识别及处理系统能够识别产品形状、个数及完整性等.结论:改良后的料罐提高了半流体食品打印的卫生性、生产效率,且便于耗材的更换,能加工出复杂糖画模型以满足造型独特的个性化糖艺制品的需求.     

Estimating long-term time-resolved indoor PM2.5 of outdoor and indoor origin using easily obtainable inputs

To evaluate the separate impacts on human health and establish effective control strategies, it is crucial to estimate the contribution of outdoor infiltration and indoor emission to indoor PM_2.5 in buildings. This study used an algorithm to automatically estimate the long-term time-resolved indoor PM_2.5 of outdoor and indoor origin in real apartments with natural ventilation. The inputs for the algorithm were only the time-resolved indoor/outdoor PM_2.5 concentrations and occupants’ window actions, which were easily obtained from the low-cost sensors. This study first applied the algorithm in an apartment in Tianjin, China. The indoor/outdoor contribution to the gross indoor exposure and time-resolved infiltration factor were automatically estimated using the algorithm. The influence of outdoor PM_2.5 data source and algorithm parameters on the estimated results was analyzed. The algorithm was then applied in four other apartments located in Chongqing, Shenyang, Xi'an, and Urumqi to further demonstrate its feasibility. The results provided indirect evidence, such as the plausible explanations for seasonal and spatial variation, to partially support the success of the algorithm used in real apartments. Through the analysis, this study also identified several further development directions to facilitate the practical applications of the algorithm, such as robust long-term outdoor PM_2.5 monitoring using low-cost light-scattering sensors.     

Inconel 690传热管GTAW对接焊接头组织及力学性能研究

对Inconel 690传热管材进行钨极气体保护焊(GTAW)对接焊,采用拉伸试验机、压扁试验机和光学显微镜测试和分析传热管焊接接头,同时利用ANSYS软件开展焊接接头在设计工况失压时的一次应力强度校核。研究结果表明:焊缝中心为树枝胞状晶,熔合线附近为粗大柱状晶。室温时接头的平均抗拉强度为619 MPa,平均屈服强度为292 MPa,350℃时接头平均抗拉强度为475 MPa,平均屈服强度为206 MPa,拉伸接头断裂从熔合区开始贯穿整个焊缝组织,呈塑性断裂。压扁试验和反向压扁试验结果表明管接头完好。通过ANSYS分析可知,设计工况下传热管接头350℃许用应力强度150 MPa限值可满足其一次应力强度要求,且裕量较大。     

Enhanced electrochemical performance of LiNi0.8Co0.1Mn0.1O2 via titanium and boron co-doping

Titanium and boron are simultaneously introduced into LiNi_0.8Co_0.1Mn_0.1O₂ to improve the structural stability and electrochemical performance of the material. X-ray diffraction studies reveal that Ti⁴⁺ ion replaces Li⁺ ion and reduces the cation mixing; B³⁺ ion enters the tetrahedron of the transition metal layers and enlarges the distance of the [LiO₆] layers. The co-doped sample has spherical secondary particles with elongated and enlarged primary particles, in which Ti and B elements distribute uniformly. Electrochemical studies reveal the co-doped sample has improved rate performance (183.1 mAh·g^-1 at 1 C and 155.5 mAh·g^-1 at 10 C) and cycle stability (capacity retention of 94.7% after 100 cycles at 1 C). EIS and CV disclose that Ti and B co-doping reduces charge transfer impedance and suppresses phase change of LiNi_0.8Co_0.1Mn_0.1O_2.     

ZY6400/23/47型掩护式液压支架偏置改造

铁煤集团大兴矿(以下简称"大兴矿")2019年产240万t,井田位于铁法煤田的西南角,火成岩侵入及地质构造复杂,煤层破坏程度严重[1-2]。受火成岩影响,煤层瓦斯含量大幅增加[3-4],渗透性能差,力学强度低,煤的含水率低,自然发火期较短,是煤与瓦斯突出矿井。在采煤过程中,防治自然发火是重中之重,综采设备在设计初期未考虑实施灭火的操作空间,为此,笔者提出通过改造综采设备增加实施灭火的操作空间,降低出现自然发火灾害时防治的难度,保证采煤安全。     

倾斜摄影测量技术在古建筑测绘中的运用研究——以郴州市汝城县朱氏宗祠建筑测绘为例

为测试倾斜摄影测量技术路线,并通过实际项目的应用,解决传统古建筑建模过程中存在的时间成本高、难以还原复杂场景等问题。按照倾斜摄影技术的技术路线,进行朱氏宗祠建筑测绘试验,并通过基于altizure软件建立三维模型来展现倾斜摄影测量技术流程。验证无人机倾斜摄影应用于古建筑三维建模的可行性和可操作性。     

CAN总线的输送控制系统集成化研究

针对现有技术中输送系统控制不稳定、控制能力低下等问题,本文提出基于工业CAN总线的输送系统集成化控制.在控制系统CAN通信节点利用代码进行数据的转化,通过emit关键字将数据绘制成显示曲线,由输入的代码不断对系统数据进行刷新,实现了输送系统的实时监控,提高了系统运行的安全性.通过时间同步技术将SAEAS6802时钟同步协议与时钟修正算法相结合,有效地对数据处理时间和接收时间进行校正,减少了数据接收误差,提高了时间同步精度.实验结果表明,本文研究方法提高了输送控制系统的运行安全性和可靠性.