Spatiotemporal Magnetocaloric Microenvironment for Guiding the Fate of Biodegradable Polymer Implants

The degradation behavior of implants is significantly important for bone repair. However, it is still unprocurable to spatiotemporally regulate the degradation of the implants to match bone ingrowth. In this paper, a magneto-controlled biodegradation model is established to explore the degradation behavior of magnetic scaffolds in a magnetothermal microenvironment generated by an alternating magnetic field (AMF). The results demonstrate that the scaffolds can be heated by magnetic nanoparticles (NPs) under AMF, which dramatically accelerated scaffold degradation. Especially, magnetic NPs modified by oleic acid with a better interface compatibility exhibit a greater heating efficiency to further facilitate the degradation. Furthermore, the molecular dynamics simulations reveal that the enhanced motion correlation between magnetic NPs and polymer matrix can accelerate the energy transfer. As a proof-of-concept, the feasibility of magneto-controlled degradation for implants is demonstrated, and an optimizing strategy for better heating efficiency of nanomaterials is provided, which may have great instructive significance for clinical medicine.     

Hydrogen production through dry reforming of biogas using a porous electrochemical cell: Effects of a cobalt catalyst in the electrode and mixing of air with biogas

This paper reports the performance of porous Gd-doped ceria (GDC) electrochemical cells with Co metal in both electrodes (cell No. 1) and with Ni metal in the cathode and Co metal in the anode (cell No. 2) for CO₂ decomposition, CH₄ decomposition, and the dry reforming reaction of a biogas with CO₂ gas (CH₄ + CO₂ → 2H₂ + 2CO) or with O₂ gas in air (3CH₄ +?1.875CO₂ +?1.314O₂ → 6H₂ +?4.875CO +?0.7515O₂). GDC cell No. 1 produced H₂ gas at formation rates of 0.055 and 0.33?mL-H₂/(min?m²-electrode) per 1?mL-supplied gas/(min?m²-electrode) at 600?°C and 800?°C, respectively, by the reforming of the biogas with CO₂ gas. Similarly, cell No. 2 produced H₂ gas at formation rates of 0.40?mL-H₂/(min?m²) per 1?mL-supplied gas/(min?m²) at 800?°C from a mixture of biogas and CO₂ gas. The dry reforming of a real biogas with CO₂ or O₂ gas at 800?°C proceeded thermodynamically over the Co or Ni metal catalyst in the cathode of the porous GDC cell. Faraday's law controlled the dry reforming rate of the biogas at 600?°C in cell No. 2. This paper also clarifies the influence of carbon deposition, which originates from CH₄ pyrolysis (CH₄ → C + 2H₂) and disproportionation of CO gas (2CO → C + CO₂), on the cell performance during dry reforming. The dry reforming of a biogas with O₂ molecules from air exhibits high durability because of the oxidation of the deposited carbon by supplied air.     

Membrane separation of indigenous noroviruses from sewage sludge and treated wastewater.

In this study, feasibility of membrane separation for the removal of indigenous noroviruses (NVs) is evaluated. The indigenous NV gene was never detected from ultrafiltration (UF) permeates of sewage sludge and treated wastewater. Indigenous NV gene was also not detected from permeates of sewage sludge and treated wastewater by microfiltration (MF) with a pore size of 0.1 microm (MF0.1). Even though the pore size of MF (0.1 microm) was much larger than the diameter of virus particle (approximately 30-40nm), more than 4-log10 reduction value (LRV) at maximum was achieved by membrane separation with MF0.1. NV genes were often detected from permeates of sewage sludge and treated wastewater by MF with a pore size of 0.45 microm (MF0.45), although the maximum log10 reduction values were more than 3.59 for sewage sludge and more than 2.90 for treated wastewater. It is important to verify factors determining the removal efficiency of viruses with MF membranes.     

Crosslinked acrylic pressure‐sensitive adhesives. II. Effect of humidity on the crosslinking reaction

The effect of humidity during storage on the crosslinking reactions of isocyanate groups was investigated with attenuated total reflectance Fourier transform infrared spectroscopy with pressure‐sensitive adhesives composed of poly[ethyl acrylate‐co‐(2‐ethylhexyl acrylate)‐co‐(2‐hydroxyethyl methacrylate)] as a base resin and polyisocyanate as a crosslinker. A peak‐resolving analysis of the amide II region revealed four bands. According to an analysis of the Fourier transform infrared spectra of the model compounds, these four bands were assigned to free urethane linkages, hydrogen‐bonded urethane linkages, free urea linkages, and hydrogen‐bonded urea linkages. As expected, storage under humid conditions led to the formation of free and hydrogen‐bonded urea linkages corresponding to the promotion of isocyanate consumption. Peak resolution of the amide II region was found to be a reasonable way of monitoring urethane and urea linkages during crosslinking reactions. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3039–3045, 2003     

Augmentation of boiling heat transfer from horizontal cylinder to liquid by movable particles

This paper presents a series of experimental results on a passive augmentation technique of boiling heat transfer by supplying solid particles in liquid. A cylindrical heater 0.88 mm in diameter is placed in saturated water, in which a lot of mobile particles exist, and the nucleate and film boiling heat transfer characteristics are measured. Particle materials used were alumina, glass, and porous alumina, and the diameter ranged from 0.3 mm to 2.5 mm. Particles are fluidized by the occurrence of boiling without any additive power, and the heat transfer is augmented. The maximum augmentation ratio obtained in this experiment reaches about ten times the heat transfer coefficient obtained in liquid alone. The augmentation ratio is mainly affected by the particle material, diameter, and the height of the particle bed set at no boiling condition. The augmentation mechanism is discussed on the basis of the experimental results. © 2001 Scripta Technica, Heat Trans Asian Res, 31(1): 28–41, 2002     

ASYMPTOTIC PROPERTIES OF THE SAMPLE AUTOCORRELATIONS AND PARTIAL AUTOCORRELATIONS OF A MULTIPLICATIVE ARIMA PROCESS

Abstract. We shall investigate the asymptotic behaviour of the sample autocorrelations and partial autocorrelations of a multiplicative ARIMA process and derive their limiting distributions. Some simulations are presented to illustrate the results obtained.     

Preparation and antibacterial activity of novel fluoroalkyl end-capped oligomers/silica nanocomposites-encapsulated low molecular biocides

Fluoroalkyl end-capped N-(1,1-dimethyl-3-oxobutyl)acrylamide oligomer [R_F-(DOBAA) _n -R_F] reacted with tetraethoxysilane (TEOS) and silica nanoparticles in the presence of low-molecular weight biocides such as hibitane, hinokitiol, and hinokioil under alkaline conditions to afford R_F-(DOBAA) _n -R_F/silica nanocomposites-encapsulated these biocides in excellent to moderate isolated yields. Fluoroalkyl end-capped N,N-dimethylacrylamide oligomer [R_F-(DMAA) _n -R_F] and acrylic acid oligomer [R_F-(ACA) _n -R_F]/silica nanocomposites-encapsulated hibitane were obtained under similar conditions. Dynamic light scattering measurements showed that the size of these fluorinated nanocomposites-encapsulated biocides thus obtained is nanometer size-controlled. Additionally, these fluorinated nanocomposites were shown to have a good dispersibility and stability in methanol and water. Of particular interest, these fluorinated nanocomposites-encapsulated biocides were found to have a good antibacterial activity against Staphylococcus aureus, and these nanocomposites were applied to the surface modification of traditional organic polymers such as poly(methyl methacrylate).     

Effect of light source spectral modulation on wavelength interrogation in fiber Bragg grating sensors and its reduction

In the fiber Bragg grating sensing using a superluminescent diode as the light source and an arrayed waveguide grating as the wavelength interrogator, the wavelength measurement error due to the spectral modulation of the superluminescent diode is theoretically formulated and quantitatively analyzed by computer simulation. It is shown that the wavelength measurement errors produced with the use of real superluminescent diodes are in very good agreement with the theoretical results. In order to reduce the wavelength measurement error due to the spectral modulation of superluminescent diode, two different types of remedies are proposed that utilize the temperature switching of superluminescent diode and that adjust the bandwidths of fiber Bragg grating and arrayed waveguide grating, and their efficacies are experimentally demonstrated together with good quantitative agreement with the theoretical calculation.     

Real-time measurement of pointing action by using DSP

This paper presents an approach of measuring in real-time the vector of finger that is pointing to an object. DSP is used in the operation processing unit in order to do the real-time processing. The steps include the extraction of flesh-colored regions from an image, the labeling of the flesh-colored regions, and the detection of two characteristic positions on the finger so that the direction that the finger is pointing at will be calculated. The entire process takes about 29 msec, which makes it possible to have the frame rate of 34 fps. With this frame rate, this measurement approach is considered real-time and promising to be merged into other application systems. This work was presented in part at the 13th International Symposium on Artificial Life and Robotics, Oita, Japan, January 31–February 2, 2008     

A 322 MHz random-cycle embedded DRAM with high-accuracy sensing and tuning

A 16 Mb embedded DRAM macro in a fully CMOS logic compatible 90 nm process with a low noise core architecture and a high-accuracy post-fabrication tuning scheme has been developed. Based on the proposed techniques, 61% improvement of the sensing accuracy is realized. Even with the smallest 5 fF/cell capacitance, a 322 MHz random-cycle access while 32 ms data retention time which contributes to save the data retention power down to 60 /spl mu/W are achieved.