Process Intensification of Living Cationic Polymerization of Isobutylene by a Flow Reaction System

Increasing the reaction temperature of the living cationic polymerization of isobutylene is crucial for industrial production due to the cost of refrigeration. The reaction temperature increase was achieved with an accelerated reaction rate using a flow reaction system. The polymerization conditions, including the flow reactor design, were based on the results of kinetic studies. Utilizing a milli‐scale flow reactor, polyisobutylene, which has a narrow molecular weight distribution, was obtained within a considerably short residence time at a high temperature. Furthermore, it was confirmed that the value of M_w/M_n correlates with the product of the Reynolds number and the angle of collision.     

No involvement of APC gene mutations in ulcerative colitis-associated rat colon carcinogenesis induced by 1-hydroxyanthraquinone and methylazoxymethanol acetate

In 1992, 1531 women aging 25-45 years from 5 urban and rural regions were interviewed about infertility and subfecundity within the German part of a study by the European community. 1248 of them had a positive reproductive history with 3018 pregnancies. 400 (= 13.25%) occurred during contraception. This affected 296 women (= 19.6% of all women). Smoking seems to have a promotion effect. The risk of ectopic pregnancies seems to be higher in contraceptive users. The highest fetal loss was found in women using an IUD. There were no differences in the course and outcome of pregnancy between users and nonusers of contraceptives. About 40% of the women in the corresponding group reported an irregular application of the contraceptive technique.     

Radiation tolerance of type IIa synthetic diamond detector for 14 MeV neutrons

Radiation tolerance of a type IIa synthetic diamond detector was examined from irradiation of mono-energetic 14 MeV neutrons. Measurements of I–V (current–voltage) characteristics and energy spectrum for 5.486 MeV alpha particles were performed after neutron irradiation. In the I–V characteristics measurement, enhancement of rectification was observed after neutron irradiation of up to 2.0 × 10¹² n/cm². Concurrently with the enhancement of rectification, significant decrease in signal amplitude was observed in energy spectrum measurement for alpha particles. It is considered that these changes were due to increase in the concentration of defects acting as shallow energy levels in the forbidden band. For neutron irradiation of higher than 1.6 × 10¹³ n/cm², weakening of the rectification characteristics and recovery of the signal amplitude were observed. These changes imply that deep energy levels, which were also considered to be introduced by defects, were dominant and weakened the effects of the shallow energy levels. Increase in the concentration of the deep trapping levels resulted in gradual decrease of the signal amplitude and degradation in the energy resolution. The peak for the alpha particles was obtained up to 5.5 × 10¹³ n/cm².     

Phase behavior of N‐isopropylacrylamide/acrylic acid copolymer hydrogels prepared with ultrasound

N‐Isopropylacrylamide/acrylic acid copolymer hydrogels were synthesized with ultrasound. The thermoresponsive phase behaviors of gels synthesized with ultrasound (US gels) were investigated and compared with those of gels synthesized in the absence of ultrasound (FR gels). The US gels showed thermoresponsive swelling behavior with a large hysteresis over a wide range of temperatures around its phase‐transition temperature. The hysteresis became larger with an increasing copolymerized acrylic acid content. The US gels were also characterized from the viewpoint of chemical, hydration, and macroscopic physical structures. Little difference was observed in the chemical and hydration structures of the FR gels and US gels. The macroscopic physical structure of the US gels was, however, distinct from that of the FR gels. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2449–2452, 2003     

Characterization and Sintering Behavior of Alkoxide-Derived Aluminosilicate Powders

Submicrometer SiO₂-Al₂O₃ powders with compositions of 46.5 to 76.6 wt% Al₂O₃ were prepared by hydrolysis of mixed alkoxides. Phase change, mullite composition, and particle size of powders with heating were analyzed by DTA, XRD, IR, BET, and TEM. As-produced amorphous powders partially transformed to mullite and Al-Si spinel at around 980°C. The compositions of mullite produced at 1400° and 1550°C were richer in Al₂O₃ than the compositions of stable mullite solid solutions predicted from the phase diagram of the SiO₂-Al₂O₃ system. Particle size decreased with increasing Al₂O₃ content. The sintered densities depended upon the amount of SiO₂-rich glassy phase formed during sintering and the green density expressed as a function of particle size.     

Tribological Characteristics of SiC Ceramics in High-Temperature and High-Pressure Water

The effects of temperature and sliding speed on the tribological behavior of a SiC ceramic by sliding on the same material in deoxygenated water were investigated from room temperature to 300°C under the corresponding saturated vapor pressures. The friction coefficient and specific wear rates of both plates and disks increased at elevated temperatures at all sliding speeds, but decreased with increasing sliding speed at 120° and 300°C. Fine mirrorlike worn surfaces were observed without wear debris under all sliding conditions. The wear mechanism appears to consist of hydrothermal oxidation of SiC and dissolution of reaction products such as silica.     

Transient analysis of the release and reduction of NOx using a Pt/Ba/Al2O3 catalyst

The release and reduction of NO_x in a NO_x storage-reduction (NSR) catalyst were studied with a transient reaction analysis in the millisecond range, which was made possible by the combination of pulsed injection of gases and time resolved time-of-flight mass spectrometry. After an O₂ pulse and a subsequent NO pulse were injected into a pellet of the Pt/Ba/Al₂O₃ catalyst, the time profiles of several gas products, NO, N₂, NH₃ and H₂O, were obtained as a result of the release and reduction of NO_x caused by H₂ injection. Comparing the time profiles in another analysis, which were obtained using a model catalyst consisting of a flat 5 nmPt/Ba(NO₃)₂/cordierite plate, the release and reduction of NO_x on Pt/Ba/Al₂O₃ catalyst that stored NO_x took the following two steps; in the first step NO molecules were released from Ba and in the second step the released NO was reduced into N₂ by H₂ pulse injection. When this H₂ pulse was injected in a large amount, NO was reduced to NH₃ instead of N₂.

A only small amount of H₂O was detected because of the strong affinity for alumina support. We can analyze the NO_x regeneration process to separate two steps of the NO_x release and reduction by a detailed analysis of the time profiles using a two-step reaction model. From the result of the analysis, it is found that the rate constant for NO_x release increased as temperature increase.     

Microstructures of functionally graded materials fabricated by centrifugal solid-particle andin-situ methods

Functionally graded materials (FGMs) belong to a relatively new class of inhomogeneous composite materials, in which the composition and/or microstructure undergo a gradual change along some directions. In this review article, the microstructures and composition gradients in Al/SiC, Al/Shirasu (volcanic eruptions commonly found in south Kyushu in Japan), Al/Al₃Ti, Al/Al₃Ni, Al/Al₂Cu FGMs have been investigated. The Al/SiC, Al/Shirasu and Al/Al₃Ti FGMs are fabricated by the centrifugal solid particle method where the distribution particles of SiC, Shirasu and Al₃Ti are solids in the melts. On the other hand, Al/Al₃Ni and Al/Al₂Cu FGMs are fabricated by the centrifugalin-situ method where Al/Al₃Ni and Al/Al₂Cu systems have lower liquidus temperatures than the processing temperatures. The feature of Al/(Al₃Ti−Al₃Ni) hydrid FGM, which is fabricated by a method combining both the centrifugal solid-particle andin-situ methods, is also shown.     

Relationship between crystallinity and device characteristics of In‐Sn‐Zn oxide

We have reported that the transistors having the c‐axis‐aligned crystalline (CAAC) In‐Ga‐Zn oxide (IGZO) show good performance. Recently, In‐Sn‐Zn Oxide (ITZO) has attracted much attention because of its high electron mobility, as well as IGZO. However, it has been reported that ITZO field effect transistors (FET) tend to have positive Vth (normally‐on characteristics) and poor reliability compared with IGZO‐FETs. We have reported that high‐performance and high‐reliability OS‐FETs can be fabricated by using CAAC‐IGZO, which has high crystallinity and has no clear grain boundaries, as an active layer. Therefore, we have fabricated CAAC‐ITZO thin films to improve performance of ITZO‐FETs by using CAAC‐ITZO as an active layer. In addition, FETs employing CAAC‐ITZO have better characteristics and reliability than FETs using nano‐crystal ITZO. Furthermore, constant photocurrent method (CPM) measurement was carried out in order to estimate density of deep‐level defect states caused by oxygen vacancies in oxide semiconductors. The results show that CAAC‐ITZO has lower density of deep‐level defect states than nano‐crystal ITZO. We attribute the improvement in reliability of ITZO‐FETs to a decrease in deep‐level defect states of an ITZO active layer, as is the case with IGZO.