Correlation between motion of source bender element and feedback signal induced by self-monitoring

Since the introduction of bender element tests to soil testing, the reliability of the estimated travel time has been the most serious problem. The author has previously shown a potential solution whereby removing the response of the bender element subsystem from the whole response could dramatically improve the accuracy of the travel time estimation. In order to lay the foundation for estimating the response of the bender element subsystem, this paper examines the correlation between the displacements of the element and the induced feedback signals by employing a self-monitoring element. The response of the self-monitoring element is modeled as a transfer function involving two internal transfer functions that relate the input signals to the displacements and the displacements to the feedback signals, respectively. Using a laser displacement sensor, the displacements are directly measured through the entire surface and reveal the three-dimensional bending motion of the element oscillating in both longitudinal and width directions. The feedback signals are similar to, but inconsistent with, the tip displacements, and an attempt is made to correct the feedback signals. Finally, a conclusion is given on the potential for estimating the response of the bender element subsystem using the self-monitoring element.     

Time-dependent deformation in an enhanced SiC/SiC composite

Time-dependent deformation in an enhanced SiC/SiC composite has been studied under constant load at high temperatures of 1200 °C, 1300 °C, and 1400 °C. Creep damage evolution was evaluated by a Young’s-modulus change of partial unloading and microscopic observation. The addition of the glassy phase in the matrix is very effective for protecting the composite from oxidation. The transient creep is dominant in creep life at all the temperatures. An empirical equation is proposed to describe creep behavior of the composite. It is found that creep activation energy increases with creep time at stresses lower than matrix cracking stress, but the activation energy remains constant at stresses higher than the matrix cracking stress. The creep strain rate of the composite is considered to be controlled by creep of fibers based on examining the time, strain, stress, and temperature dependencies of creep strain rates.     

Radiation tolerance for the SMASH-series front-end chips for a silicon micro-strip detector

The radiation tolerance for prototype front-end chips designed for a silicon micro-strip detector was examined with a ⁶⁰Co irradiation source to establish an allowable range of the radiation dose. The irradiated front-end chips were SMA²SH-64A, a 64-channel preamplifier array; SMA²SH-1, a single-channel preamplifier circuit with a comparator; and Control-C, a digital-control chip for the preamplifiers.     

Effective thermal conductivity of compressed woods

Compression is one solution to improve the strength of softwoods. The effective thermal conductivities of compressed Japanese cedars (cryptomeria japonica), which were compressed in the radial direction of the wood, were measured. Both the effective thermal conductivities in the tangential and fiber directions increase proportionally to the density increment due to the compression. However, the thermal conductivity in the radial direction (compression direction) increases slightly with the density increment. Numerical computations were conducted to explain the characteristics of thermal conductivity in the radial direction by using a microscopic heat conduction model for the compressed wood. The numerical results were compared with the measured values. And the physical mechanism of the heat conduction in the compressed woods is discussed.     

Development of a single loop EPR test method and its relation to grain boundary microchemistry for alloy 600

A single loop electrochemical potentiokinetic reactivation test method has been developed for alloy 600 that produces good passivation on all the surfaces, good etching during the reactivation scan and no appreciable pitting. It is able to quantify and discriminate between samples with a wide range of degree of sensitization. The Pa value correlates well with the minimum level of chromium in the depletion regions at the grain boundaries. It has been shown that the width of the attacked regions is much larger than the width of chromium depletion regions and it does not show any direct correlation with either depth or width or with a volume parameter of chromium depletion regions. It has been shown that the chromium carbides are not attacked during the test and that the intragranular regions attacked during the test are the sites of chromium carbides in the grain matrix. A modified Pa parameter is shown to be sensitive down to 7.5 wt% chromium in the depletion regions and indicates that the intragranular carbides have shallower depletion profiles than those at grain boundaries. Comparison of the results of the single loop and the double loop tests showed a good correlation.     

Recovery retardation in equal channel angular pressed Al–Zr alloy during friction stir welding

The effect of Zr on reduction of hardness and microstructure in an FS weld of equal channel angular-pressed Al alloy was investigated. Zr addition to Al suppressed dynamic recovery in the thermomechanically affected zone and enabled retention of the high hardness of the ECA-pressed material throughout the weld.     

Effects of high molecular weight component on crystallization of polyethylene under shear flow

Crystallization of polyethylene (PE) blends of low and high molecular weight components under shear flow was studied using time-resolved depolarized light scattering (DPLS), focusing on effects of the high molecular weight component on the shish-kebab structure formation. Anisotropic two-dimensional scattering pattern due to shish-like structure formation was observed above a certain concentration of the high molecular weight PE. The threshold was about 2.5-3 times larger than the chain overlap concentration, suggesting an important role of entanglements of the high molecular weight component. On the basis of these results a gel-spinning-like mechanism for the shish-like structure formation has been proposed. The DPLS results also implied that the shish-like structure was mainly formed from the high molecular weight PE. This was confirmed by small-angle neutron scattering (SANS) and small-angle X-ray scattering (SAXS) measurements on an elongated PE blend of low molecular weight deuterated PE and high molecular weight hydrogenated PE (3 wt%).     

The heat transfer and pressure drop characteristics of finned tube banks in forced convection (effects of fin height on pressure drop characteristics)

In recent years the requirement for the reduction of energy consumption has been increasing to solve the problems of global warming and the shortage of petroleum resources. For example, in the power generation field, as thermal power generation occupied 60% of the power generation demand, considerable improvement of the thermal efficiency is required. This paper describes the pressure drop characteristics of finned tube banks used for heat exchangers in thermal power generation that were clarified by testing serrated finned tube banks with different fin heights for improved heat transfer and conventional spiral finned tube banks with different fin heights, and an equation to predict pressure drop which is necessary for the heat exchanger design is proposed. © 2006 Wiley Periodicals, Inc. Heat Trans Asian Res, 35(3): 179–193, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20112     

STM tunneling spectroscopy on high Tc superconductors

STM tunneling spectroscopy has been performed on the bulk single crystals of BiSrCaCuO (BSCCO) and the epitaxial thin films of YBaCuO (YBCO) at cryogenic temperatures. The STM images and tunneling spectra observed on the (001) surfaces can be classified into three cases; 1) Atomic image is visible. However, the tunneling spectrum shows semiconducting or smeared superconducting gap structures, depending on the tip-sample distance. 2) Clear atomic image can not be obtained. But, the tunneling spectrum shows flat bottom region with quite low zero bias conductance. 3) Tunneling spectra demonstrate gapless behavior, independent of the tip-sample separation. These observations support the quasi-2D electronic picture in whichs-wave like 2D superconducting layers are coupled with each other through the Josephson effect.     

Combined pars plana vitrectomy, lens removal and intraocular lens implantation for complications of diabetic retinopathy. Surgical results in 120 cases

We performed combined vitrectomy, lens removal and posterior chamber intraocular lens implantation for proliferative diabetic retinopathy in 120 eyes of 101 patients. Follow-up periods ranged from 3 to 63 months, with a mean of 17 months. Three lens removal methods were used: extracapsular cataract extraction (14 eyes), phacoemulsification and aspiration (49 eyes), and pars plana phacoemulsification (57 eyes). Preoperative rubeosis iridis or neovascular glaucoma was found in 21 eyes. Gas or temporary silicone oil tamponade was employed in 32 eyes. Surgical results were good, and the postoperative vision was finger counts or below only in 13 eyes. Thus the combined surgery proved to have no serious problems. Our results indicate two important points. (1) It is best to chose either of the following two methods for the lens surgery: phacoemulsification with continuous circular capsulorhexis, self sealing sclerocorneal incision, and in-the-bag fixation of the posterior chamber lens, or pars plana phacoemulsification leaving the anterior capsule, rub off and aspirating the lens epithelial cells, continuous circular capsulorhexis, and posterior chamber lens implantation in front of the anterior capsule from a self-sealing sclerocorneal wound. (2) It is mandatory to do complete vitrectomy and cut out the vitreous gels incarcerated in the sclerotomy site.