A practical Equivalent Electrical Circuit model for Proton Exchange Membrane Fuel Cell (PEMFC) systems

An alternative Equivalent Electrical Circuit for Proton Exchange Membrane Fuel Cells is modelled in this study. Both I–V characteristics and H₂ consumptions corresponding to generated power under load and no-load conditions are investigated. For this purpose, H₂ consumptions and I–V characteristics of three different sized PEMFCs are tested. There is a very good harmony between the model results and measured values (relative error %0.7, %6.4 and %2.5 for FC-A, FC-B and FC-C respectively). In the proposed model current passes only on parallel resistance and not on serial resistance at no-load condition. Thus, a FC with higher parallel resistance should be preferred. Another key output of this study is that based on the proposed model, performance comparison of FCs can be performed with the parameters defined in this work. Proposals made in this study can easily be used for performance analysis of FCs under for both steady state and transient analysis.     

Partitioning of predominant lipophilic bioactives (squalene, α-tocopherol and β-sitosterol) during olive oil processing

The partitioning of predominant lipophilic olive bioactives (squalene, β-sitosterol and α-tocopherol) in olive oil processing was studied for the first time using common integrated olive milling plant. 7% of the oil and 5% of the squalene present in the olives was lost in the last pomace. β-sitosterol and α-tocopherol, which are mainly concentrated in the seed of the olive fruit, was recovered in virgin olive oil to a lesser extent (66%, 67%) while 10% were lost in last pomace. Thus, the loss of β-sitosterol and α-tocopherol was higher than that of squalene and oil, due to nonrecovered bound forms. 19% of the α-tocopherol and 21% of the β-sitosterol loss was unaccounted for, which can be attributed to degradation of α-tocopherol and incomplete recovery of sterols from the olive and pomace matrices. This study provides a basis for process development studies.     

Optimal design of elastic beams with segmentwise constant height in the case of dynamic loading

A shape optimization method for elastic beams with segmentwise constant height is proposed. The ends of the beam are simply supported, clamped or free. Two problems are discussed; (i) a beam is loaded by lateral pressure, (ii) a beam is struck by an attached mass. External loads and volume of the beam are prescribed and the deflection in a given cross-section is to be minimized. For solving this problem, the deflections are expanded into a Fourier series by eigenfunctions. Numerical results are given for two-, three- and four-stepped beams.     

Production of hydrogen over bimetallic Pt–Ni/δ-Al2O3: I. Indirect partial oxidation of propane

Indirect partial oxidation (IPOX) of propane was studied over bimetallic 0.2 wt.% Pt–15 wt.% Ni/δ-Al₂O₃ catalyst in the 623–743 K temperature range. The unreduced and reduced forms of the catalyst were characterized by ESEM–EDAX and X-ray diffraction (XRD). In the IPOX tests, the effects of steam to carbon ratio (S/C), carbon to oxygen ratio (C/O₂) and residence time (W/F (g_cat h/mol HC)) on the hydrogen production activity, selectivity and product distribution were studied in detail. The effect of temperature program applied (increasing from 623 to 743 K, ITP; decreasing from 743 to 623 K, DTP) during reaction was also tested. The results showed that the Pt–Ni bimetallic system has superior performance characteristics compared to the monometallic catalysts reported in literature. The reason is thought to be the utilization of the catalyst particles as micro heat exchangers during IPOX; the heat generated by Pt sites during exothermic total oxidation (TOX) being readily transferred through the catalyst particles acting as micro heat exchangers to the Ni sites, which promote endothermic steam reforming (SR). The optimal conditions were found as S/C = 3, C/O₂ = 2.70 and W/F = 0.51 g_cat h/mol HC for IPOX of propane on the basis of high hydrogen productivity and selectivity between 623 and 748 K for the experimental conditions tested. The thermo-neutral points obtained showed the sustainability of reaction in terms of energy.     

Possibilities and problems with the use of models as a communication tool in water resource management

Politicians and policy-makers, as well as modellers, often nurses an expectation that model derived results is an objective source of information that can be used to support decisions. However, several prerequisites have to be dealt with in order to ensure that models can be used as legitimate and efficient tools in water resource management. Based on empirical material from recent studies on the use of models in stakeholder dialogues, mainly focusing on catchment nutrient transport, two central problems are identified: (a) Models are laden with choices and thus depend on assumptions and priorities of modellers. (b) There are several factors that influence ability and willingness of stakeholders (as information recovers) to criticize or accept results of the modelling exercise. Recognized factors likely to influence stakeholders' acceptance of model derived results include issues at stake, stakeholders' ability to criticize model derived information, and their trust in the institutions that have developed or applied the used models. Identified prerequisites for successful use of models in integrated water resource management include: consideration of user relevance, awareness of and preparedness to handle constraints linked to communication of model-based results, transparency of used models and data and of involved uncertainties, mutual respect between experts and stakeholders and between involved stakeholder groups, a robust institutional network, and sufficient time for dialogues. Development and use of strategies for participatory modelling, based on a continuous dialogue between experts and stakeholders is recommended as a way to facilitate that the prerequisites for a successful use of models in water resource management are fulfilled.     

工业项目的海绵城市建设标准与技术要点

工业用地是城市建设用地的主要类型之一,是海绵城市建设的重要区域。通过梳理工业项目硬化面积高、径流污染程度高等特征,针对性提出其海绵城市建设的实施路径、建设标准和技术应用等实施建议。工业项目的海绵城市设计应遵循因地制宜的原则,应合理布局绿地并建设海绵设施,通过精细化的标高设计进行径流组织设计;对于降雨径流污染严重的三类工业项目,其海绵措施应以雨水调蓄池(应急事故池)为主,严禁设置具有渗透功能的源头控制设施。对于三类工业项目,海绵城市所提出的年径流总量控制率的目标与事故池的环保要求基本一致,建议相关部门在制定(修订)的应急事故池设计标准时,其中的径流污染控制体积可与对应区域年径流总量控制率标准协同一致。     

Polymeric absorbent for water sorption based on chemically crosslinked poly (acrylamide/2-acrylamido-2-methyl-1-propanesulfonic acid sodium salt) hydrogels

Summary Swelling equilibrium of polyelectrolyte copolymer gels containing of acrylamide (AAm) and 2-acrylamido-2-methyl-1-propanesulfonic acid sodium salt (AMPS) have been studied as a function of copolymer composition. AAm/AMPS hydrogels were prepared by free radical solution polymerization in aqueous solution of AAm with AMPS as anionic comonomer and two multifunctional crosslinkers such as ethylene glycol dimethacrylate (EGDMA) and trimethylolpropane triacrylate (TMPTA). Swelling experiments were performed in water at 25 °C, gravimetrically. The influence of AMPS content in hydrogels was examined. Swelling of AAm/AMPS hydrogels was increased up to 1018% (for containing 2% AMPS and crosslinked by EGDMA) 15246% (for containing 8% AMPS and crosslinked by TMPTA), while AAm hydrogels swelled up to 804% (crosslinked by TMPTA)–770% (crosslinked by EGDMA). The values of equilibrium water content of the hydrogels are 0.8851–0.9935. Diffusion behavior was investigated. Water diffusion into hydrogels was found to be non-Fickian in character.     

Unveiling the presence of mixed oxidation states of Europium in Li7+δEuxLa3−δZr2−δO12−δ garnet and its impact on the Li-ion conductivity

Recently, lanthanides have been employed by researchers to examine their impact on the structure and properties of Li₇La₃Zr₂O₁₂ (LLZO) garnets. In this regard, we developed Europium oxide (Eu₂O₃) doped LLZO (Li_7+δEu_xLa_3−δZr_2−δO_12−δ) solid electrolyte which demonstrates a cubic phase with the symmetry of Iad (No.230) at room temperature. In this investigation, different concentrations of Eu ranging from 0.1 to 0.6 atoms per formula unit (pfu) were doped into Li₇La₃Zr₂O₁₂ to evaluate the impact of Eu on the stability of the cubic phase and thereby the ionic conductivity. The results unveiled that upon doping Eu³⁺ ions, the Eu²⁺ state is also formed and is then self-doped into the structure in which Rietveld refinement coupled with XPS, EPR, and solid-state NMR suggests that Eu³⁺ ions most probably partially occupy Zr⁴⁺ (16a) site, the Eu²⁺ ions occupy La³⁺ (24d) site, and the Li⁺ ions occupy two different sites (24d and 96h). It was further found that such a site preference induces distortion at LaO₈ polyhedrons opening up the neck for Li-ions diffusion, thereby enhancing the ionic conductivity. Moreover, it was revealed that Li-ions probably hop from 96h to 24d and then to 96h site to generate the Li-ion movement. Overall, by introducing Eu ions into the LLZO structure, an enhanced bulk ionic conductivity of 0.30 × 10⁻³ S/cm at 298 K with a minimum electronic conductivity of 2.547 × 10⁻⁹ S/cm at 298 K was achieved.     

基于信道状态特征的手势动作识别技术研究

手势识别作为人和机器之间重要的交互手段,在日常生活中具有广泛的应用场景。基于无线信号特别是WiFi的手势识别由于其无接触、成本低等优点成为当前热门的方式。为解决传统基于无线信号手势识别算法没有充分利用信号相位特征的缺点,本文提出利用WiFi信道状态信息幅值和相位结合的方式进行手势识别。通过子载波降维和动作曲线提取对接收的WiFi信号进行处理,并将信号的幅值和相位结合,利用机器学习算法对数据进行训练和分类,实现了单手向前、单手向后、单手向左、单手向右、单手向上和单手向下六种手势的识别。实验结果显示,本文算法在近距离和远距离下的精确度分别为96%和92%。