搅拌摩擦加工SiC复合层对镁合金摩擦磨损性能的影响

研究了搅拌摩擦加工（FSP）AZ91D镁合金SiC复合层的微观组织和磨损性能。结果表明,复合层SiC粒子分布均匀,晶粒细小,成分均一,抗摩擦磨损性能较基体有大幅度提高。     

搅拌摩擦加工(FSP)AZ91D镁合金的组织分析

研究了AZ91D镁合金经搅拌摩擦加工后的组织。发现组织中搅拌摩擦区、热机械影响区和热影响区分区不明显。在搅拌摩擦区主要为再结晶形成的细小均匀的等轴晶结构,共晶组织α-Mg β相(Mg17Al12)完全均匀化,仅在晶界处有少量存在。     

组合式中央空调机组无干扰切换

纺织厂用组合式中央空调机组,当工艺送风机出现故障时,用环境风机代替工艺风机的无干扰切换。结果表明:当工艺风机出现故障,人为手动无干扰切换,用环境风机代替工艺风机,环境风温与风压均能满足工艺送风要求,停下工艺风机进行故障维修处理,满足生产工艺要求。     

浅谈中央空调离心风机轴承的养护

主要介绍了纺丝用中央空调离心风机滚动轴承的安装、润滑以及点检等相关养护知识,以减少设备故障,提升设备运行效率,其中重点介绍了轴承的润滑与点检的要点及注意事项。     

成形工艺参数对触变成形AZ91D镁合金滑动磨损性能的影响

研究了模具温度、锭料加热温度和加热时间对触变成形AZ91D镁合金滑动摩擦磨损性能的影响。结果表明,随着模具温度的升高,合金的磨损率逐渐升高;随着锭料加热温度的升高,合金的磨损率先降低后升高;随着锭料加热时间的增加,合金的磨损率逐渐升高。不同的触变成形工艺参数对AZ91D镁合金的摩擦系数影响不大。     

工业机器人在涤纶长丝生产中的应用

简要介绍了工业机器人的发展历史和基本构成,重点介绍了涤纶长丝自动落筒系统的组成,自动落筒的工作流程,相关机器人的参数和操作流程。工业机器人首次在涤纶长丝生产中得到应用,起到了"机器换人"的目的,实现了化纤成套生产线自动化与智能物流化的结合。     

Friction stir processing of thixoformed AZ91D magnesium alloy and fabrication of Al-rich surface

The microstructural evolution characteristics of thermo-mechanically affected zone were investigated during friction stir processing (FSP) of the thixoformed AZ91D alloy. Simultaneously, an Al-rich surface layer was prepared by combination of Al powder using FSP method. The results indicate that the dynamic recrystallization and mechanical separation (including splitting and fracture of the primary grains) are the main mechanisms of grain refinement. For the thixoformed alloy, the operation efficiency of these mechanisms is less than that of the permanent mould casting AZ91D alloy, thus its microstructural evolution is relatively slow and the resulting grain size is relatively large. These are attributed to the differences in their original microstructures. The Al-rich surface layer can obviously improve the corrosion resistance in NaCl aqueous solution. A proper solution heat treatment (at 415 ℃ for 1 h) can further increase the corrosion resistance. In order to improve corrosion resistance, increasing the amount and improving the distribution uniformity of the Al-rich phase are more effective than increasing the Al solubility in the matrix.     

浅谈雾霾天气时纺丝车间空调的处理流程

分析了油污丝产生的原因,介绍了当外界产生雾霾时,通过投用冷冻水、调节新回风比的中央空调调节方式,并调整车间正负压,减少外界烟雾进入生产车间,从而降低油污丝产生概率,提高产品品质,提升企业的竞争力。     

搅拌摩擦加工次数对AZ91D镁合金组织的影响

研究了搅拌摩擦加工(FSP)次数对AZ91D镁合金组织的影响.结果表明:加工次数对搅拌摩擦区晶粒大小影响不大;但加工次数多可增加搅拌摩擦区组织的面积,并使组织均匀化;使热机械影响区组织向搅拌摩擦区组织发生转变;增大轴肩下压区细晶组织面积,进一步细化轴肩下压区的晶粒.