全文获取类型
收费全文 | 120篇 |
免费 | 10篇 |
国内免费 | 45篇 |
专业分类
电工技术 | 1篇 |
综合类 | 5篇 |
化学工业 | 18篇 |
金属工艺 | 3篇 |
矿业工程 | 1篇 |
武器工业 | 125篇 |
无线电 | 7篇 |
一般工业技术 | 14篇 |
自动化技术 | 1篇 |
出版年
2024年 | 1篇 |
2023年 | 2篇 |
2022年 | 3篇 |
2021年 | 2篇 |
2020年 | 4篇 |
2019年 | 5篇 |
2018年 | 5篇 |
2017年 | 8篇 |
2016年 | 3篇 |
2015年 | 3篇 |
2014年 | 2篇 |
2013年 | 3篇 |
2012年 | 2篇 |
2011年 | 15篇 |
2010年 | 7篇 |
2009年 | 14篇 |
2008年 | 13篇 |
2007年 | 9篇 |
2006年 | 18篇 |
2005年 | 13篇 |
2004年 | 10篇 |
2003年 | 7篇 |
2002年 | 6篇 |
2001年 | 7篇 |
2000年 | 3篇 |
1999年 | 1篇 |
1998年 | 1篇 |
1997年 | 2篇 |
1996年 | 4篇 |
1995年 | 1篇 |
1994年 | 1篇 |
排序方式: 共有175条查询结果,搜索用时 31 毫秒
1.
电流除了用罗果夫斯基线圈进行测量外,还可通过环探头测量电流产生的磁场来计算得到。直线电机除了位置固定的母线导体外,还有沿母线运动的电枢;母线回路注入脉冲电流后,电枢会被加速而运动。简化母线和电枢为线电流模型,在长线模型基础上,通过环探头测量得到的磁场计算出近似电流波形。因为探头所测磁场主要由其附近电流所贡献,所以合理配置电枢起始位置与探头位置后,电枢运动对电流测量的影响很小。在瞬态电流上升沿、平台区和下降沿的不同阶段,利用实验折算的系数,可得到时域瞬态电流波形,其测量结果与用罗果夫斯基线圈测量波形一致。 相似文献
2.
3.
The effect of surface roughness of aluminum oxide (95%) substrate on the properties of Ni-Cr alloy thin film is studied.The thin films are prepared on the substrates with different roughness by using magnetron sputtering.The micro-structure,adhesive and electrical properties of the thin films were investigated by using scanning electron microscopy,scratch method and four-probe method.The burst voltage and current of the thin film transducers with different substrates were measured according to D-optimization method.The results show that the particle size,structural defect,resistivity and adhesion strength of the thin film increase with the increase of the substrate roughness.The difference among the burst time of the samples with difference substrate roughness gradually decreases with the increase of stimulation amount.The burst time is approximate to 20 μs in the charging voltage of 37 V. 相似文献
4.
镀镍碳化硅纤维红外消光率研究 总被引:1,自引:1,他引:0
以表面镀覆金属的超细陶瓷纤维为研究对象,从介质与入射电磁波相互作用的角度出发,应用电磁场数值模拟技术预估陶瓷纤维材料在军用红外波段消光率随材料本征属性变化的规律,着重研究消光率发生突变时上述参量对应的值域区间。研究发现:纤维的长径比对消光截面影响很明显,尤其是在中远红外波段,当长径比在20~200之间变化时,消光截面增加很快;当纤维长径比取值在50~200范围时,对应的折射率虚部小于20可获得理想的消光率;复电导率实部在106~108s/m范围内时,纤维的消光截面较大。依据计算结果,通过控制化学镀工艺条件制备出满足要求的功能材料,并利用溴化钾压片法和小型烟箱实验对镀覆前后陶瓷纤维的质量消光系数进行对比,实验数据证实镀镍碳化硅的红外消光性能显著提高。 相似文献
5.
强闪光烟火药过载能力的实验研究 总被引:1,自引:1,他引:0
采用大落锤冲击装置模拟研究了强闪光烟火药的过载能力。实验结果表明:强闪光烟火药在装药密度为1.9×103kg.m-3,实验加载应力653 MPa,装药长度为40 mm时承受的过载为8.59×105g(g=10 m.s-2);在加载应力小于653 MPa范围内,强过载产生的热点不能引燃该强闪光药柱。原因可能是(1)强闪光烟火药中氧化剂的热分解温度和可燃物的着火点很高,难以诱发反应;(2)装药质量得到很大改善,热点产生源减少;(3)压药过程使得KC lO4和铝粉的接触面积增大,热点源产生的热量可以通过金属颗粒较迅速向其周围传递,以致热点熄灭。 相似文献
6.
7.
8.
9.
10.