全文获取类型
收费全文 | 50篇 |
免费 | 0篇 |
国内免费 | 25篇 |
专业分类
综合类 | 10篇 |
化学工业 | 2篇 |
金属工艺 | 25篇 |
机械仪表 | 1篇 |
建筑科学 | 15篇 |
能源动力 | 1篇 |
轻工业 | 1篇 |
水利工程 | 2篇 |
石油天然气 | 2篇 |
一般工业技术 | 6篇 |
冶金工业 | 6篇 |
原子能技术 | 4篇 |
出版年
2023年 | 1篇 |
2019年 | 4篇 |
2018年 | 3篇 |
2017年 | 3篇 |
2016年 | 1篇 |
2014年 | 3篇 |
2013年 | 7篇 |
2012年 | 1篇 |
2011年 | 4篇 |
2010年 | 1篇 |
2009年 | 2篇 |
2008年 | 1篇 |
2007年 | 2篇 |
2005年 | 2篇 |
2004年 | 4篇 |
2003年 | 1篇 |
2002年 | 1篇 |
2001年 | 1篇 |
2000年 | 3篇 |
1999年 | 2篇 |
1998年 | 2篇 |
1997年 | 5篇 |
1996年 | 8篇 |
1995年 | 8篇 |
1993年 | 1篇 |
1991年 | 3篇 |
1988年 | 1篇 |
排序方式: 共有75条查询结果,搜索用时 15 毫秒
1.
2.
3.
Fe-C-Ti-Mn合金系中TiC原位生成反应的热力学分析 总被引:4,自引:1,他引:4
根据溶液热力学理论对Fe C Ti Mn体系中TiC增强体的原位合成进行了热力学分析。计算表明,体系中TiC优先于Fe3C和Fe2Ti形成,且在热力学上比Fe3C和Fe2Ti稳定。多数情况下,TiC基体合金在液态未凝固时即可形成,而Fe3C和Fe2Ti则是在合金凝固和冷却过程中才有可能析出。随C含量增加,形成TiC和Fe3C的可能性增大;随Ti含量增加,形成Fe2Ti的可能性增大,而形成Fe3C的可能性减小;高Ti高C时,有利于形成TiC,高Ti低C时有利于形成Fe2Ti;高C低Ti时有利于形成Fe3C;添加适量的Mn既可有效抑制Fe3C的形成,又明显降低TiC的合成温度,使大多数TiC的合成反应发生在合金熔体充满铸型后的冷却、凝固过程中,可能解决TiC过早析出、熔体粘度增大、充型困难等问题。 相似文献
4.
In order to examine the effect of extrusion ratio on the microstructure and mechanical behavior in Al-Cu-Mg-Ag alloy, the Al-6.3 Cu-0.48 Mg-0.4 Ag alloy was subjected to extruding with different extrusion ratios of 17, 30 and 67. The results indicate that the grains are refined and the strength is improved effectively with increasing extrusion ratio. However, further investigation shows that the extrusion ratio of 30 is more effective than the lower extrusion ratio(17) and the higher extrusion ratio(67) to refine the grains in the T6-temper alloy. Moreover, the sample with an extrusion ratio of 30 obtains more precipitates and superior mechanical properties after T6 treatment. This study supports the idea that there exists a critical extrusion ratio for grain refinement and improvement of mechanical properties for the T6-temper alloy. Recrystallization and precipitation during T6 treatment were introduced to explain the effects of extrusion ratio on the microstructure and mechanical properties of the Al-Cu-Mg-Ag alloys. 相似文献
5.
6.
研究了悬浮处理对铸造热锻模具钢(JCD钢)的显微组织和力学性能的影响。结果表明,悬浮处理后的铸造热锻模具钢,结晶组织得到细化,偏析倾向减小,铸件硬度从HRC395提高到4415,冲击韧性从2026J/cm2提高到5482J/cm2,抗热疲劳性提高了约一倍,断面力学性能的均匀性和耐磨性均有较大幅度的提高,可满足热锻模具使用性能的要求。 相似文献
7.
8.
赵宇光 《中国石油和化工标准与质量》2019,(11):10-11
乌兹别克斯坦某盆地XX-15井的主试油层位KKC层是裂缝与溶洞发育的非均质碳酸盐岩层,高温高压高含硫化氢和二氧化碳,地层压力系数高达1.9,易喷易漏且喷、漏同存,压井困难。试油工艺存在多工种、多工序、立体交叉连续作业的特点,在试油作业过程中存在诸多高风险因素。采用科学的方法对井控风险进行识别和评价,制定风险控制措施,并使用多种HSE工具进行关键工序的过程控制确保试油全过程的井控安全。 相似文献
9.
10.
在Al-B4C粉末体系中通过采用低氧压熔结技术在Ti-6Al-4V合金表面成功制备出原位内生TiC-TiB2颗粒增强金属基复合材料涂层.XRD检测表明涂层主要由TiC、TiB2、TiAl3、Al2O3和Al组成,外层TiC和TiB2颗粒含量(体积分数)约为55%,各层之间表现出较强的结合能力.通过对涂层形成机制的研究,Al在涂层制备过程中主要起到类似稀释剂、催化剂、辅助剂、除氧剂和填充剂作用,为涂层的制备提供了一种更加便利的途径. 相似文献