A novel open-loop high-speed CMOS sample-and-hold

A new open-loop high-speed CMOS sample-and-hold is presented. Based on new method for further reduction of voltage-dependent charge injection, a new CMOS sample-and-hold was designed. Simulation results confirm the effectiveness of this method. Over 10 dB improvement in signal-to-noise ratio, compared to the signal-to-noise ratio of conventional bottom plate sampling S/Hs was achieved with this method. A comparison between newly designed S/H and the bottom-plate sampling S/H is presented.     

Lower critical solution temperature behavior of ethylene propylene copolymers in multicomponent solvents

The lower critical solution temperature (LCST) locus for ethylene-propylene copolymers has been determined as a function of pressure in a variety of single and multicomponent solvents. The lower critical end-point temperature (LCEP), which is the intersection of the LCST locus with the vapor-pressure curve, was found to be predictable from the solvent density as previously established for single-component solvents by Charlet and Delmas.¹ Dissolving a low-molecular hydrocarbon gas such as propylene in an alkane has a dramatic effect on lowering the LCEP, and can reduce phase-separation temperatures to levels at which this technique becomes attractive as a practical method for polymer recovery from diluents such as those used in solution polymerizations. Temperatures considerably above the LCEP are needed to minimize the residual polymer concentration in the solvent in the two-liquid-phase region. The solvent critical temperature must be approached for essentially complete elimination of the polymer from the solvent phase. The LCST locus was found to be a linear function of pressure for all of the systems investigated, and the slope of the line, d(LCST)/dP, could be well correlated as a function of solvent density and critical temperature. From the relationship between the LCEP and solvent density and the correlation for d(LCST)/dP, the location of the LCST locus can be readily predicted from a knowledge of solvent properties.     

Optimal production of intermediate for zero—first and first—first order reaction sequences in fluidised bed reactors1

An analysis of zero—first and first—first order reaction schemes has been carried out in a fluidised bed with a view to optimising the production of intermediate R for a given bubble diameter. For the zero—first order reaction sequence, the gas residence time at which the maximum concentration of R occurs is shown to be fixed and independent of bubble size in the bed. On the other hand, for a first—first order reaction scheme, an optimum gas residence time exists for the concentration maximum to occur at the bed exit. This interaction between bubble diameter, gas residence time and maximum concentration of intermediate is resolved by recourse to a three dimensional diagram which optimises the production of intermediate for any given value of bubble diameter or gas residence time.     

Modification of glassy carbon electrode with multi-walled carbon nanotubes and iron(III)-porphyrin film: Application to chlorate, bromate and iodate detection

In this study, multi-wall carbon nanotubes (MWCTs) is evaluated as a transducer, stabilizer and immobilization matrix for the construction of amperometric sensor based on iron-porphyrin. 5,10,15,20-Tetraphenyl-21H,23H-porphine iron(III) chloride (Fe(III)P) adsorbed on MWCNTs immobilized on the surface of glassy carbon electrode. Cyclic voltammograms of the Fe(III)P-incorporated-MWCNTs indicate a pair of well-defined and nearly reversible redox couple with surface confined characteristics at wide pH range (2-12). The surface coverage (Γ) and charge transfer rate constant (k_s) of Fe(III)P immobilized on MWCNTs were 7.68 × 10⁻⁹ mol cm⁻² and 1.8 s⁻¹, respectively, indicating high loading ability of MWCNTs for Fe(III)P and great facilitation of the electron transfer between Fe(III)P and carbon nanotubes immobilized on the electrode surface. Modified electrodes exhibit excellent electrocatalytic activity toward reduction of ClO₃⁻, IO₃⁻ and BrO₃⁻ in acidic solutions. The catalytic rate constants for catalytic reduction of bromate, chlorate and iodate were 6.8 × 10³, 7.4 × 10³ and 4.8 × 10² M⁻¹ s⁻¹, respectively. The hydrodynamic amperometry of rotating-modified electrode at constant potential versus reference electrode was used for detection of bromate, chlorate and iodate. The detection limit, linear calibration range and sensitivity for chlorate, bromate and iodate detections were 0.5 μM, 2 μM to 1 mM, 8.4 nA/μM, 0.6 μM, 2 μM to 0.15 mM, 11 nA/μM, and 2.5 μM, 10 μM to 4 mM and 1.5 nA/μM, respectively. Excellent electrochemical reversibility of the redox couple, good reproducibility, high stability, low detection limit, long life time, fast amperometric response time, wide linear concentration range, technical simplicity and possibility of rapid preparation are great advantages of this sensor. The obtained results show promising practical application of the Fe(III)P-MWCNTs-modified electrode as an amperometric sensor for chlorate, iodate and bromate detections.     

Are U.K. Citizens Satisfied With E-Government Services? Identifying and Testing Antecedents of Satisfaction

Citizens’ satisfaction is acknowledged as one of the most significant influences for e-government adoption and diffusion. This study examines the impact of information quality, system quality, trust, and cost on user satisfaction of e-government services. Using a survey, this study collected 1518 valid responses from e-government service adopters across the United Kingdom. Our empirical outcomes show the five factors identified in this study have a significant impact on U.K. citizens’ satisfaction with e-government services.     

Adaptive content-and-deadline aware chunk scheduling in mesh-based P2P video streaming

In mesh-based Peer-to-Peer (P2P) live video streaming systems packet scheduling is an important factor in overall video playback quality. In mesh based P2P video streaming systems, each video sequence is divided into chunks, which are then distributed by multiple suppliers to the receivers. The suppliers need to be coordinated by the receiver through specifying a transmission schedule for each of them. Many previous studies on scheduling of P2P streaming tend to mainly focus on networking issues which strongly depend on a particular P2P architecture such as tree or mesh. These algorithms suffer from some design issues: 1) they are too complex to deploy, 2) they do not take video characteristics into account and 3) they do not have sender-side transmission policy. To address all three of these problems, we propose a new chunk scheduling scheme which consists of two parts: i) receiver-side scheduler and ii) sender-side transmission order scheme. The proposed receiver-side scheduler considers the contribution level of each video frame as well as the frame’s urgency in order to define a priority for each video frame. It attempts to request frames with highest priority from peers which can deliver them in a shorter time. We also design a new chunk transmission order scheme that decides which requested chunk will be sent out first based on its importance to the requesting neighbor. Our simulation results show that the proposed scheduling scheme improves the overall quality of the perceived video in mesh-based P2P video streaming architectures substantially.     

Predicting performance in ASEAN banks: an integrated fuzzy MCDM–neural network approach

This paper presents a performance assessment of 88 Association of Southeast Asian Nations banks from 2010 to 2013, using an integrated three‐stage approach on financial criteria that emulates the CAMELS rating system. More precisely, fuzzy analytic hierarchy process is used first to assess the relative weights of a number of criteria related to capital adequacy (C), asset quality (A), management quality (M), earnings (E), liquidity (L), and sensitivity to market risk (S) based on the opinion of 88 Association of Southeast Asian Nations experts. Then, these weights are used as technique for order of preference by similarity to ideal solution inputs to assess their relative efficiency. Lastly, neural networks are combined with technique for order of preference by similarity to ideal solution results to produce a model for banking performance with effective predictive ability. The results reveal that contextual variables have a prominent impact on efficiency. Specifically, parsimony in equity leveraging derived from Islamic finance principles may be the underlying cause in explaining higher efficiency levels.