Sol-gel processed barium titanate ceramics and thin films

Ferroelectric barium titanate (BaTiO3) ceramics and thin films have been prepared from barium acetate (Ba(CH3COO)2) and titanium (IV) isopropoxied (Ti((CH3)2CHO)4) precursors by a sol–gel technique. The as-grown powder and thin films were found to be amorphous, which crystallized to the tetragonal phase after annealing at 700°C in air for 1 h. Both the ceramics and thin films showed well-saturated polarization–field (P–E) hysteresis loops at room temperature. The value of the spontaneous polarization, PS, remnant polarization, Pr, and coercive field, Ec, of the ceramics and thin films determined from the P–E hysteresis loop were found to be 19.0 and 12.6; 14.0 and 3.2 G cm–2, and 30 and 53 kV cm–1, respectively. The coercive field of the film determined from the capacitance–voltage, C–V, characteristics is slightly lower than that determined from the P–E hysteresis loop (43 kV cm–1). The room-temperature dielectric constant, , of the ceramics and films was found to be 1135 and 370, respectively. Both the films and ceramics showed dielectric anomaly peaks at 125 °C, showing ferroelectric to paraelectric phase transition. © 1998 Kluwer Academic Publishers     

Dielectric properties of sol-gel derived barium-strontium-titanate (Ba(0.4)Sr(0.6)TiO(3)) thin films

The structural and dielectric properties of sol-gel derived barium-strontium-titanate (Ba(0.4)Sr(0.6)TiO(3 )) thin films have been investigated. The as-fired films are found to be amorphous, and films crystallize to a cubic phase after a post deposition annealing at 700 degrees C for one hour in air. The variation of dielectric constant with temperature and field was investigated as a function of film thickness. These films display a nonlinear dielectric response that can be described in terms of a power series expansion of the free energy in polarization as in Landau-Ginzburg-Devonshire approach. The measured room temperature dielectric constant (epsilon') of the film was about 320. The dielectric constant did not show any significant frequency dependence up to 100 kHz. The temperature dependence of dielectric constant exhibited a diffused ferroelectric to paraelectric phase transition at -60 degrees C. The room temperature dielectric constant and magnitude of the dielectric peak at the Curie point was dependent on the thickness of the film. The obtained dielectric data on sol-gel barium strontium titanate thin films on platinized substrates were analyzed in the light of a barrier layer model.     

Charge transport and structural morphology of HCl-doped polyaniline

The d.c. and a.c. (100 Hz–1 MHz) conductivities of HCl-doped polyaniline have been measured in the temperature range 77–300 K. At 77 K, the a.c. conductivity data, (), can be described by the relation ()=As, where the parameter s lies close to unity and decreases with increase in the doping level. The ratio of measured a.c. to d.c. conductivity shows dispersion at 77 K, which decreases with increase in the doping level. This decrease is found to be sharp around pH3.0. In the temperature range 77–150 K, the observed d.c. conductivity data can be described by Mott's three dimensional variable range hopping (VRH) model. Scanning electron microscopy studies reveal a sharp change in structural morphology of HCl-doped polyaniline at a pH3.0. A strikingly remarkable structural morphology has been observed in the formc of a channel at this pH value. This change is accompanied by a rapid increase in d.c. conductivity, dielectric constant, along with sharp changes in structural morphology, which indicates the existence of a doping-induced structural conductivity correlation in this system. © 1998 Chapman & Hall     

Influence of surface treatment on properties of Cocos nucifera L. Var typica fiber reinforced polymer composites

Natural fibers are a powerful competitor in the polymer composite market due to their availability, sustainability, obtainability, cost, and biodegradability. The surface of natural fibers was changed to increase mechanical qualities, hydrophobicity, and bonding with polymer matrix. This study exposes the influence of several surface treatments of coconut tree peduncle fibers (CTPFs) on the thermomechanical and water absorption properties of CTPF-reinforced polymer composites. The CTPFs were treated with sodium hydroxide, benzoyl peroxide, potassium permanganate and stearic acid at a constant 40 wt% and individually reinforced in an unsaturated polyester resin matrix containing 60 wt% CTPFs. Chemically treated CTPFs improved reinforcement-matrix adhesion and enhanced composite mechanical characteristics. In addition, the scanning electron microscope fractographical study of stressed composite specimens shows improved reinforcement-matrix bonding. Moreover, the treated CTPFs have a higher cellulose wt%, which improves the composites crystalline nature, hydrophobicity and thermal stability. The potassium permanganate treated CTPF composite's maximum tensile strength of 128 MPa, flexural strength of 119 MPa, impact strength of 9.9 J/cm², hardness value of 99 HRRW and thermal stability up to 193°C make them appropriate for lightweight mobility and structural applications.     

Dielectric and pyroelectric properties of triglycine sulphate-polystyrene composites

A composite of Triglycine sulphate (TGS) and polystyrene has been fabricated by mixing different particle size TGS powders (75 μm to 400 μm) and polystyrene solution. The dielectric constant has been measured in the frequency range 0.1 to 100 KHz, and the pyroelectric current measurements were made by the Byer and Roundy direct method. Specific heat of the composite was determined by the differential them analysis (DTA) technique.

Particle size dependance of dielectric constant, pyroelectric coefficient and responsivity have been studied. Anomalies in ε' and P_y were observed even in the composite with the lowest particle size of TGS (75 μm). The surface effects have much greater influence on electrical properties but thermal properties are, not affected. This is indicated by a decrease in ε' and P^y with decreasing particle size of TGS, while specific heat of composite is almost independent of particle size.     

Proposing a decision support system for automated mobile asthma monitoring in remote areas*

ABSTRACT

Advances in mobile computing have paved the way for the development of several health applications using Smartphone as a platform for data acquisition, analysis and presentation. Such areas where m-health systems have been extensively deployed include monitoring of long-term health conditions such as cardio-vascular diseases and pulmonary disorders, as well as detection of changes from baseline measurements of such conditions. Asthma is one of the respiratory conditions with growing concern across the globe due to the economic, social and emotional burden associated with the ailment. The management and control of asthma can be improved by consistent monitoring of the condition in real-time since attack could occur anytime and anywhere. This paper proposes the use of smartphone equipped with built-in sensors, to capture and analyze early symptoms of asthma triggered by exercise. The system design is based on decision support system (DSS) techniques for measuring and analyzing the level and type of patient’s physical activity as well as weather conditions that predispose asthma attack. Preliminary results show that smartphones can be used to monitor and detect asthma symptoms without other networked devices. This would enhance the usability of the health system while ensuring user’s data privacy, and reducing the overall cost of system deployment. Further, the proposed system can serve as a handy tool for a quick medical response for asthmatics in low-income countries where there is limited access to specialized medical devices and shortages of health professionals. Development of such monitoring systems signals a positive response to lessen the global burden of asthma.     

Dielectric properties of sol-gel derived barium strontium titanate thin films

Barium strontium titanate (Ba_xSr_1−xTiO₃) films were deposited by sol-gel technique on platinized silicon substrate for the composition range x = 0.0 to 1.0 in steps of 0.1. The as-deposited films were found to be amorphous. The films crystallize on annealing in air at 700 °C for 1 h. Dielectric constant (ε′) and loss tangent (tanδ) were measured in the temperature range − 180 °C to 150 °C in the frequency range 0.1 to 100 kHz. Both ε′ and tanδ show a small dispersion for all the compositions. This dispersion is more at the peak value than at room temperature. A comparison of the room temperature and peak value of the dielectric constant for various compositions are made with the reported values. Transition temperatures are reported for the entire composition range. All the compositions show a transition from ferroelectric to paraelectric phase except strontium titanate. Transition temperature shows a systematic decrease with increase in strontium content. The variation is at a rate of 3.4 °C/mol% of SrTiO₃. Curie constants are also reported for the entire composition range.     

Electrical characterization of amorphous germanium dioxide films

Amorphous germanium dioxide (GeO₂) films have been deposited by electron beam evaporation onto different substrates including glass, SnO₂ conducting glass, evaporated gold and n-type silicon in order to examine the electrical behaviour of GeO₂ in metal/insulator/metal (MIM) and metal/insulator/semiconductor (MIS) structures. In MIM structures the as-deposited films are strongly influenced by electrode barriers but heat treatment at 600 K induced ohmic behaviour. The dielectric response of the films in the frequency range 0.1–100 kHz and the temperature range 180–350 K showed that the dielectric constant at 300 K was 9 and was virtually independent of frequency, while the a.c. conductivity follows the relation σ ∞ ω^s, where s is temperature dependent. Good agreement with a classical electronic hopping model is obtained. In MIS structures, GeO₂ on silicon gives rise to heterojunction behaviour at low voltages while, at higher voltages, the d.c. conduction is bulk dominated and exhibits space-charge-limited conduction. The dielectric response of MIS structures is strongly influenced by the depletion capacitance at the interface between GeO₂ and silicon.     

Role of Universities in IT Education in India

In the wake of the information technology (IT) revolution, the paper describes the changing role of universities to promote IT education in India to generate qualitative and competitive manpower in the face of the mushrooming of private institutions in the field of IT. The rapid growth of private teaching initiatives reflects inadequacies of the public educational system to the needs of the emerging IT environment, especially considering the high prices charged by private training. It is pointed out that the emerging knowledge society and the economy are not going to be based on IT alone, but will depend on the development of both IT and basic research in domain areas. Any policy on IT education should ensure that basic disciplines are not ignored. Universities should develop new and innovative programmes for students from different basic disciplines to give training for high-end jobs. To promote IT education a new innovative concept of earning while learning has recently been introduced. Some of the initiatives started by Delhi University to modify/improve course programmes for IT education are highlighted, looking at the needs of the industry.     

Sol-gel processed barium titanate thin films

Ferroelectric barium titanate (BaTiO₃) thin films have been prepared by sol-gel technique from barium acetate [Ba(CH₃COO)₂] and titanium (IV) isopropoxied [Ti(CH₃)₂CHO)₄] precursors. The as-grown films were found to be amorphous which crystallized to tetragonal phase after annealing at 700°C for one hour in air. The room temperautre dielectric constant (ε) and loss tangent (tanδ) of the films were found to be 370 and 0.02 respectively. The values of the spontaneous polarization (P_s), remanent polarization (P_r) and coercive field (E_c) of the films determined from the polarization-field (P-E) hysteresis were found to be 14.0, 3.2μC-cm^-2 and 53KV-cm^-1 respectively. The coercive field of the film determined from the capacitance-voltage (C-V) characteristics is slightly lower than that determined from the P-E hysteresis loop.