Bovidae-based gelatin: Extractions method,physicochemical and functional properties,applications, and future trends

Gelatin is one of the most important multifunctional biopolymers and is widely used as an essential ingredient in food, pharmaceutical, and cosmetics. Porcine gelatin is regarded as the leading source of gelatin globally then followed by bovine gelatin. Porcine sources are favored over other sources since they are less expensive. However, porcine gelatin is religiously prohibited to be consumed by Muslims and the Jewish community. It is predicted that the global demand for gelatin will increase significantly in the future. Therefore, a sustainable source of gelatin with efficient production and free of disease transmission must be developed. The highest quality of Bovidae-based gelatin (BG) was acquired through alkaline pretreatment, which displayed excellent physicochemical and rheological properties. The utilization of mammalian- and plant-based enzyme significantly increased the gelatin yield. The emulsifying and foaming properties of BG also showed good stability when incorporated into food and pharmaceutical products. Manipulation of extraction conditions has enabled the development of custom-made gelatin with desired properties. This review highlighted the various modifications of extraction and processing methods to improve the physicochemical and functional properties of Bovidae-based gelatin. An in-depth analysis of the crucial stage of collagen breakdown is also discussed, which involved acid, alkaline, and enzyme pretreatment, respectively. In addition, the unique characteristics and primary qualities of BG including protein content, amphoteric property, gel strength, emulsifying and viscosity properties, and foaming ability were presented. Finally, the applications and prospects of BG as the preferred gelatin source globally were outlined.     

Studies on influence of hydrogen and carbon monoxide concentration on reduction progression behavior of molybdenum oxide catalyst

Temperature programmed reduction (TPR) analysis was applied to investigate the chemical reduction progression behavior of molybdenum oxide (MoO₃) catalyst. The composition and morphology of the reduced phases were characterized by X-ray diffraction spectroscopy (XRD), X-ray photoelectron spectroscopy (XPS), and field emission scanning electron microscopy (FE-SEM). The reduction progression of MoO₃ catalyst was attained with different reductant types and concentration (10% H₂/N₂, 10% and 20% CO/N₂ (%, v/v)). Two different modes of reduction process were applied. The first approach of reduction involved non-isothermal mode reduction up to 700 °C, while the second approach of reduction involved the isothermal mode reduction for 60 min at 700 °C. Hydrogen temperature programmed reduction (H₂-TPR) results showed the reduction progression of three-stage reduction of MoO₃ (Mo⁶⁺ → Mo⁵⁺ → Mo⁴⁺ → Mo⁰) with Mo⁵⁺ and Mo⁴⁺. XRD analysis confirmed the formation of Mo₄O₁₁ phase as an intermediate phase followed by MoO₂ phase. After 60 min of isothermal reduction, peaks of metallic molybdenum (Mo) appeared. Whereas, FESEM analysis showed porous crater-like structure on the surface cracks of MoO₂ layer which led to the growth of Mo phase. Meanwhile, the reduction of MoO₃ catalyst in 10% carbon monoxide (CO) showed the formation of unstable intermediate phase of Mo₉O₂₆ at the early stage of reduction. Furthermore, by increasing 20% CO led to the carburization of MoO₂ phase, resulted in the formation of Mo₂C rather than the formation of metallic Mo, as confirmed by XPS analysis. Therefore, the presented study shows that hydrogen gave better reducibility due to smaller molecular size, which contributed to high diffusion rate and achieved deeper penetration into the MoO₃ catalyst compared to carbon monoxide reductant. Hence, the reduction of MoO₃ in carbon monoxide atmosphere promoted the formation of Mo₂C which was in agreement with the thermodynamic assessment.     

Role of Nd-Ni on structural,spectral and dielectric properties of strontium-barium based nano-sized X-type ferrites

The influence of neodymium and nickel substitution on structural and dielectric parameters was investigated in strontium-barium X-type hexagonal ferrites having composition SrBaCu_2?xNi_xNd_yFe_28?yO₄₆ (x = 0, 0.2, 0.4, 0.6, 0.8, 1 and y = 0, 0.02, 0.04, 0.06, 0.08, 0.1). Sol-gel method was employed for synthesizing these hexagonal ferrites. The XRD plots of all studied materials which were annealed at 1250 °C show single phase characteristics. Lattice parameter ‘c’ increased as a consequence of larger radius of rare earth ion (Nd³⁺) as compared to (Fe³⁺), while lattice parameter ‘a’ showed very small variation. The cell volume was obtained in the range 2508.32–2523.75 (ų). The inclusion of Nd-Ni also affected X-ray density, bulk density and porosity. The FTIR spectroscopy indicated the particular absorption peaks of hexagonal ferrites and it was performed in the range of 500–700 cm^?1. On account of Nd-Ni doping, the dielectric constant, dielectric loss and AC-conductivity showed decreasing trend. The occupancy of Nd³⁺ ions at octahedral site impedes the valence alternation of Fe³⁺; therefore there was decrease in dielectric permittivity. Ac conductivity has been decreased from 9.14 to 6.49 (Ω cm)^?1 at frequency of 2.7 GHz. The Cole-Cole plots of synthesized materials noticeably revealed grain boundary contribution. The appearance of single semi-circle in impedance Cole-Cole graphs confirms the exceptional role of grain boundaries in the conduction process. The considerably lower dielectric parameters of investigated nano X-type ferrites propose their feasibility for high-frequency applications (phase shifters, dielectric resonators, stealth technology etc).     

Thermo-protective properties of polymer composites with nano-titanium dioxide

International Journal of Mechanics and Materials in Design - The present work investigates the ablative and thermal properties of an epoxy resin which was modified with titanium dioxide...     

Dynamic Analysis of Truss‐Beam System

As the manned exploration of space continues, many complex structural components are being developed to construct the orbital platforms that will be used to house communication hardware, personnel, and manufacturing complexes. These components are extremely flexible and complex in their behavior. There is a need for a simple method for determining the dynamic characteristics of these space structures with a minimum of effort. A mathematical model of one of these structural elements, an articulating truss beam, has been developed to predict its dynamic response. Assumptions of the force interaction between the beam elements and the joints have been made for using this model. Algorithms are provided to determine the flexibility matrix of the truss beam for use in the equation of motion. The natural frequencies obtained from using this method are compared with those obtained by the finite element method. An experimental procedure is planned to validate the results from the theoretical method.     

A knowledge-based system for sensor selection

This paper presents a Knowledge-based system (KBS) developed to allow users, who may not be knowledgeable about sensors, to select sensors suitable for their specific needs. The KBS runs on a micro-computer. The selection criteria are user specified and are based on the desired measurement parameters. The system output includes all of the operational and dimensional parameters of the recommended sensor, price, and vendor information.     

Evaluation of simple dynamic models and controllers for hydraulic and nozzle pressure in injection molding

Simple pseudo-steady state relations between the hydraulic and nozzle pressures of an injection molding machine were presented and verified experimentally. A simulation study was performed to evaluate the performance of simple controllers using dynamic models developed for the hydraulic and nozzle pressures. The controllers chosen were the discrete proportional, proportional-integral (PI), and proportional-integral-derivative (PID) types, tuned according to the ITAE criterion. The control of hydraulic pressure simulation showed that the PI controller had the best overall performance, whereas the result of nozzle pressure control loop simulation showed that the PID controller performance was better than that of the PI controller. All the controllers, in both loops, gave responses that were about an order of magnitude more rapid than the open loop response.