Use of Zebrafish Embryo Assay to Evaluate Toxicity and Safety of Bioreactor-Grown Exopolysaccharides and Endopolysaccharides from European Ganoderma applanatum Mycelium for Future Aquaculture Applications

Natural mycelial exopolysaccharide (EPS) and endopolysaccharide (ENS) extracted from bioreactor-cultivated European Ganoderma applanatum mushrooms are of potential high commercial value for both food and adjacent biopharmaceutical industries. In order to evaluate their potential toxicity for aquaculture application, both EPS (0.01–10 mg/mL) and ENS (0.01–10 mg/mL) extracts were tested for Zebrafish Embryo Toxicity (ZFET); early development effects on Zebrafish Embryos (ZE) were also analyzed between 24 and 120 h post-fertilization (HPF). Both EPS and ENS are considered non-toxic with LC₅₀ of 1.41 mg/mL and 0.87 mg/mL respectively. Both EPS and ENS did not delay hatching and teratogenic defect towards ZE with <1.0 mg/mL, respectively. No significant changes in the ZE heart rate were detected following treatment with the two compounds tested (EPS: 0.01–10 mg/mL: 176.44 ± 0.77 beats/min and ENS: 0.01–10 mg/mL: 148.44 ± 17.75 beats/min) compared to normal ZE (120–180 beats/min). These initial findings support future pre-clinical trials in adult fish models with view to safely using EPS and ENS as potential feed supplements for supplements for development of the aquaculture industry.     

Studies on influence of hydrogen and carbon monoxide concentration on reduction progression behavior of molybdenum oxide catalyst

Temperature programmed reduction (TPR) analysis was applied to investigate the chemical reduction progression behavior of molybdenum oxide (MoO₃) catalyst. The composition and morphology of the reduced phases were characterized by X-ray diffraction spectroscopy (XRD), X-ray photoelectron spectroscopy (XPS), and field emission scanning electron microscopy (FE-SEM). The reduction progression of MoO₃ catalyst was attained with different reductant types and concentration (10% H₂/N₂, 10% and 20% CO/N₂ (%, v/v)). Two different modes of reduction process were applied. The first approach of reduction involved non-isothermal mode reduction up to 700 °C, while the second approach of reduction involved the isothermal mode reduction for 60 min at 700 °C. Hydrogen temperature programmed reduction (H₂-TPR) results showed the reduction progression of three-stage reduction of MoO₃ (Mo⁶⁺ → Mo⁵⁺ → Mo⁴⁺ → Mo⁰) with Mo⁵⁺ and Mo⁴⁺. XRD analysis confirmed the formation of Mo₄O₁₁ phase as an intermediate phase followed by MoO₂ phase. After 60 min of isothermal reduction, peaks of metallic molybdenum (Mo) appeared. Whereas, FESEM analysis showed porous crater-like structure on the surface cracks of MoO₂ layer which led to the growth of Mo phase. Meanwhile, the reduction of MoO₃ catalyst in 10% carbon monoxide (CO) showed the formation of unstable intermediate phase of Mo₉O₂₆ at the early stage of reduction. Furthermore, by increasing 20% CO led to the carburization of MoO₂ phase, resulted in the formation of Mo₂C rather than the formation of metallic Mo, as confirmed by XPS analysis. Therefore, the presented study shows that hydrogen gave better reducibility due to smaller molecular size, which contributed to high diffusion rate and achieved deeper penetration into the MoO₃ catalyst compared to carbon monoxide reductant. Hence, the reduction of MoO₃ in carbon monoxide atmosphere promoted the formation of Mo₂C which was in agreement with the thermodynamic assessment.     

Al2O3/Yttria‐Stabilized Zirconia Hollow‐Fiber Membrane Incorporated with Iron Oxide for Pb(II) Removal

Removal by absorptive ceramic membranes can simultaneously absorb and separate metal ions from water. Alumina/yttria‐stabilized zirconia (Al₂O₃/YSZ) hollow‐fiber membranes, fabricated using phase inversion and sintering process, were deposited with iron oxide by an in‐situ hydrothermal process. The results showed that α‐Fe₂O₃ was produced and incorporated across the membranes. A reduction in flux was recorded with the deposition of α‐Fe₂O_3. However, it improved the adsorption capacity for heavy metal adsorption. The adsorption‐separation test demonstrated that the optimized membrane is able to completely remove Pb(II) ions after two hours.     

Bond graph modeling,design and experimental validation of a photovoltaic/fuel cell/ electrolyzer/battery hybrid power system

This work presents a complete bond graph modeling of a hybrid photovoltaic-fuel cell-electrolyzer-battery system. These are multi-physics models that will take into account the influence of temperature on the electrochemical parameters. A bond graph modeling of the electrical dynamics of each source will be introduced. The bond graph models were developed to highlight the multi-physics aspect describing the interaction between hydraulic, thermal, electrochemical, thermodynamic, and electrical fields. This will involve using the most generic modeling approach possible for managing the energy flows of the system while taking into account the viability of the system. Another point treated in this work is to propose. In this work, a new strategy for the power flow management of the studied system has been proposed. This strategy aims to improve the overall efficiency of the studied system by optimizing the decisions made when starting and stopping the fuel cell and the electrolyzer. It was verified that the simulation results of the proposed system, when compared to simulation results presented in the literature, that the hydrogen demand is increased by an average of 8%. The developed management algorithm allows reducing the fuel cell degradation by 87% and the electrolyzer degradation by 65%. As for the operating time of the electrolyzer, an increment of 65% was achieved, thus improving the quality of the produced hydrogen. The Fuel Cell's running time has been decreased by 59%. With the ambition to validate the models proposed and the associated commands, the development of this study gave rise to the creation of an experimental platform. Using this high-performance experimental platform, experimental tests were carried out and the results obtained are compared with those obtained by simulation under the same metrological conditions.     

Synthesis of heterocyclic metal complexes and their evaluation as marine antifoulants

4-Amino-3-thio-1,24-triazolidine (L₁) and 4-amino-5-thio-1,3,4-thiadiazole (L_II) as well as their metal complexes of the general formulae ML_I·2H₂O and ML_IICl (M; Pb(II), Cd(II) and Zn(II)) were prepared. With Sn(II), we obtained Sn(L_I)₂·2H₂O and SnL_IICl, respectively. The structures of the compounds were identified through elemental analysis, and IR and UV spectra measurements, in addition to thermal analysis in case of the metal complexes. The antifouling properties of the compounds were tested by their incorporation into paint formulations which were applied to PVC substrates and tested in water from Alexandria western harbour. When the compounds were added at 17·5% by volume, the coated panels were fouled after 3 months of immersion. The addition of 6·7% by volume of tributyltin oxide to 15·8% of the prepared compounds in one formulation elevated the paint efficiency and prevented fouling for 11 months. Paint containing solely tributyltin oxide at the same concentration was inactive against algae.