Post‐protection effect of heat‐resistant insulations on timber‐frame members exposed to fire

In lightweight walls and floors, the load‐bearing timber members are protected by cladding on the sides to form a divider between two fire compartments or to provide appropriate fire protection to the load‐bearing members. The spaces between the timber members can be void or filled with insulation materials. Although a huge number of different insulation materials exist, the most commonly used material is mineral wool insulation. The existing design model for glass wool‐insulated timber‐frame constructions, given in European standard 1995‐1‐2, assumes collapse of the glass wool after failure of the cladding. However, a new form of glass wool insulation, suitable for use at high maximum service temperatures, is now available in the market. The charring phase after the cladding's failure is known as the post‐protection phase. The behaviour of the new heat‐resistant glass wool in the post‐protection phase is similar to that of stone wool and considerably better than that of traditional glass wool. The protective properties of stone wool have changed over the last decades. Charring is one of the main parameters needed to calculate the resistance of a structure to fire. Based on experimental investigations, this paper describes the analysis of the effect of the insulation with regard to its ability to protect timber members against charring during the post‐protection phase. Copyright © 2011 John Wiley & Sons, Ltd.     

Selective adsorption of multivalent ions into TiC-derived nanoporous carbon

A TiC-derived carbon (TiC-CDC) was prepared, and the adsorption of large hexacyanocobaltate and tetrabutylammonium ions of approximately same size was examined on this carbon. While selectively absorbing these large ions, it rejects smaller chloride and ammonium ions in mixed electrolyte solutions. The result demonstrates the important role of electrostatic repulsive forces, space-efficient charge packing and hydrophobic ion interactions with the pore walls of TiC-CDC, similar to what is known for a variety of biological membranes.     

Corrosion properties of thermal sprayed aluminium (TSA) coatings deposited by powder flame spraying

Thermal sprayed aluminium (TSA) coatings are widely used for the protection of steels from aqueous corrosion, including offshore structures and components that are exposed to seawater immersion, tidal and splash zone environments. In this paper, the influence of deposition parameters of aluminium coating on its corrosion properties was studied. For different application parameters of TSA coatings, the thickness, the microstructure and corrosion properties were determined. Determination of thickness was performed according to EN ISO 2064:2000 relating to the definition and determination of the thickness of metallic and other inorganic layers. Microstructure was determined using a Olympus GX50 optical microscope. The corrosion properties of the coatings were compared using an accelerated electrochemical corrosion test method. Electrochemical studies were carried out in accordance with the requirements of ASTM standard G 102 – 89. The TSA coating performance was quantified in terms of its corrosion potential and the corrosion rate, which was estimated from Tafel polarisation resistance measurements.     

The quantitative composition of the intestinal lactoflora before and after space flights of different lengths

Due to the emotional stress before the take off the lactoflora of 24 cosmonouts shows distinct changes regarding the spectrum of different species of Lactobacilli. Compared to long-time flights after short-time flights even stronger alterations are observed. The reason is that the disturbances which take place before the take-off as to the short space of time cannot be balanced by the macroorganism. Additionally, after a certain adaptive period the factors of the space travel begin to act. There are characteristic individual particularities regarding the number of Lactobacilli in the saliva and the feces of the cosmonouts.     

Nanoscale fine-tuning of porosity of carbide-derived carbon prepared from molybdenum carbide

Micro- and mesoporous carbide-derived carbon (CDC) was synthesised from molybdenum carbide (Mo₂C) powder by gas phase chlorination in the temperature range from 400 to 1200 °C. Analysis of XRD results show that C(Mo₂C), chlorinated at 1200 °C, consist mainly on graphitic crystallites of mean size, L_a = 9 nm and L_c = 7.5 nm. The first-order Raman spectra showed the graphite-like absorption peak at ∼1587 cm⁻¹ and the disorder-induced (D) peak at ∼1348 cm⁻¹. The low-temperature N₂ adsorption experiments were performed and a specific surface area up to 1855 m² g⁻¹ and total pore volume up to 1.399 cm³ g⁻¹ were obtained. Sorption measurements showed the presence of both micro- and mesopores after chlorination at 400-900 °C and only mesopores after chlorination at 1000°-1200 °C. Stepwise formation of micro- and mesopores was achieved and the peak pore size can be shifted from 0.8 nm up to 4 nm by increasing the chlorination temperature.     

Four-Variable Model of an Enzymatic Oscillator Based on Trypsin

This paper describes a four-variable model for an enzymatic oscillator based on trypsin. Variables in this model are concentrations of the essential proteins (trypsin and trypsinogen) and small molecules (masked and active inhibitors of trypsin) within the network. Importantly, to simplify the model, non-essential side reactions are neglected and essential reactions are assumed to follow first or second order kinetics. Numerical solutions of this reduced model semi-quantitatively reproduce experimentally determined periods, amplitudes, and phase shifts of oscillations in the concentrations of several species in the network. Moreover, linear stability analysis shows that oscillations in the trypsin oscillator emerge and disappear through Hopf bifurcation. The model will be helpful in situations where simplicity is necessary such as detailed analysis of dynamics and modeling of reaction-diffusion systems.     

Emission measurements with gravimetric impactors and electrical devices: An aerosol instrument comparison

Particulate matter in the atmosphere is known to affect Earth’s climate and to be harmful to human health. Accurately measuring particles from emission sources is important, as the results are used to inform policies and climate models. This study compares the results of two ELPI?+?devices, two PM10 cascade impactors and an eFilter, in combustion emission measurements. The comparison of the instruments in a realistic setting shows what types of challenges arise from measuring an emission aerosol with unknown particle morphologies and densities, different particle concentrations and high temperature. Our results show that the PM10 cascade impactors have very good intercorrelation when the collected mass is greater than 150?µg, but below that, the uncertainty of the results increases with decreasing mass. The raw signals of two ELPI?+?devices were nearly identical in most samples, as well as the particle number concentrations and size distributions calculated from raw signals; however, transforming the current distributions into mass distributions showed variation in the mass concentration of particles larger than 1?µm. The real-time time signal measured by eFilter was similar to the total current measured by ELPI+. The eFilter and PM10 cascade impactors showed similar particle mass concentrations, whereas ELPI?+?showed clearly higher ones in most cases. We concluded that the difference is at least partially due to volatile components being measured by ELPI+, but not by the mass collection measurements.

Copyright © 2019 American Association for Aerosol Research