Localized corrosion of (lean) duplex stainless steels in immersion units of urban wastewater treatment plants

With lower alloying cost and higher mechanical properties, lean duplex stainless steels can be an alternative to the more commonly used austenitic stainless steels. However, these alloys are still not the preferred choice, probably due to a lack of field experience. A study was thus initiated in view of defining the limits of use of selected (lean) duplexes for urban wastewater treatment units. The present paper shows the localized corrosion performance of selected lean duplexes in chloride contaminated solutions. The results are compared with austenitic S30403 and S31603 and with the more standard duplexes S82441 and S32205. The effect of welding was also investigated. Exposures in field municipal wastewater plants were conducted for 1 year in low and high chloride content units. The results show that lean duplexes S32101 and S32202 can be used as alternatives to S30403 and S31603 in low chloride electrolytes. At 500 ppm of chloride content, duplex stainless steel S32304 showed better corrosion resistance than S30403 and S31603. For higher chloride contents (1000 ppm and above) the standard duplexes S82441 and S32205 shall be preferred.     

Long-term sensor measurements of lung deposited surface area of particulate matter emitted from local vehicular and residential wood combustion sources

Abstract

Lung deposited surface area (LDSA) is a relatively new metric that has been argued to be more accurate at predicting health effects from aerosol exposure. For typical atmospheric aerosol, the LDSA concentration depends mainly on the concentration of ultrafine particles (e.g. vehicular exhaust emissions and residential wood combustion) and therefore optical methods cannot be used to measure and quantify it. The objective of this study was to investigate and describe typical characteristics of LDSA under different urban environments and evaluate how a diffusion charging-based Pegasor AQ Urban sensor (Pegasor Ltd., Finland) can be used as an alternative to optical sensors when assessing local combustion emissions and respective LDSA concentrations. Long-term (12?months) sensor measurements of LDSA were carried out at three distinctly different measurement sites (four sensor nodes) in the Helsinki metropolitan area, Finland. The sites were affected mainly by vehicular exhaust emission (street canyon and urban background stations) and by residential wood combustion (two detached housing area stations). The results showed that the accuracy of the AQ Urban was good (R² = 0.90) for the measurement of LDSA when compared to differential mobility particle sizer. The mean concentrations of LDSA were more than twice as high at the street canyon (mean 22 µm² cm^?3) site when compared to the urban background site (mean 9.4 µm² cm^?3). In the detached housing area, the mean concentrations were 12 µm² cm^?3, and wood combustion typically caused high LDSA peaks in the evenings. High correlations and similar diurnal cycles were observed for the LDSA and black carbon at street canyon and urban background stations. The utilization of a small-scale sensor network (four nodes) showed that the cross-station variability in hourly LDSA concentrations was significant in every site, even within the same detached housing area (distance between the two sites ～670?m).     

用于便携无线设备的Wireless TrenchTM技术

射频电路设计人员常用的一条经验法则是:有源器件的fT至少应为工作频率的十倍时,现代无线设备中的射频电路才会具有良好的性能.     

Manufacturing method for monolithic dye-sensitised solar cells permitting long-term stable low-power modules

A manufacturing technique for monolithic dye-sensitised solar cells is presented. Encapsulated modules designed for indoor low-power applications have been prepared using industrial methods and equipment. Under certain conditions (light intensity <5000 lx, temperature between –10°C and 50°C, and relative humidity of appr. 50%), the modules have performed well and shown excellent long-term stability. Moreover, modules withstand illumination in combination with storage at 100% relative humidity. However, a certain degradation of the module performance takes place at illuminations exceeding 5000 lx and temperatures exceeding 50°C.     

Structure and surface properties of diaminocyclohexane plasma polymer films

Plasma polymers of three isomers of diaminocyclohexane (DACH) were deposited on polyethylene, SiO₂, and mica at 20°C. The deposition rate was measured as a function of plasma density and power; a maximum was observed in the latter function. The deposition rate was highest for the monomer with the highest flow rate. The film refractive index was observed to increase with both power density and the degree of fragmentation in the plasma. Film composition was measured by elementary analysis, and was found to be almost identical for each of the three isomers; a mechanism for the polymerization reaction is proposed. The percentage of primary amino groups decreased with increasing power density and with film thickness. Surface force measurements of the thickness and refractive index agreed well with the corresponding ellipsometry values in dry air, and am adhesive force, independent of power density, was measured. When the film was exposed to water vapor, it swelled considerably and the adhesion was determined by capillary forces. Associated with swelling, at high power, was an extremely regular 2-ply rope pattern of protruding material. © 1993 John Wiley & Sons. Inc.     

High optical power electroabsorption waveguide modulator

A sampled grating distributed Bragg reflector-laser integrated with a waveguide Franz-Keldysh modulator is investigated for high optical power applications. The EAM modulation efficiency is demonstrated to asymptotically approach a limit determined by the internal differential photodetector efficiency. Linear photocurrent and 1 dB small signal AC compression point both exceed 70 mA, indicating high saturation power.     

DETERMINATION OF TOTAL NITROGEN IN BARLEY AND MALT BY COMBUSTION METHOD—COLLABORATIVE TRIAL

A combustion method, relying on the Dumas principle, for the determination of total nitrogen in barley and malt, has been collaboratively tested by the Analysis Committee of the European Brewery Convention. Repeatability, r₉₅, and reproducibility, R₉₅, values were 0.063 and 0.116% of dry matter, respectively, for samples with nitrogen contents in the range 1.23 to 1.86% N of dry matter. There was no significant difference between these values for barley and malt. The Analysis Committee approved the adoption of the combustion method for inclusion in Analytica EBC as an alternative method.     

Biapenem versus imipenem/cilastatin in the treatment of complicated intra-abdominal infections: report from a Swedish Study Group

The objective of this study is to describe usual medical management and costs associated with recurrent respiratory infections in subjects with chronic obstructive bronchitis in France. A prospective survey was performed in Autumn 1994 on a national sample of private practice pulmonologists (N = 71). Two hundred forty-four patients, presenting at least one infection of the lower respiratory tract, were included. Bronchitis was the most frequent acute exacerbation observed (94%). Pneumonia concerned 9% of the patients. Biological tests, X-rays and pulmonary function tests were prescribed for, respectively, 59, 65 and 45% of the patients. Following the visit, 15 patients were hospitalized (6%). The direct medical cost per acute exacerbation was estimated 3,289 francs (1994 value) of which 60% were hospital-related. An average 10.4 day sick-leave was prescribed to 21% of patients in employment. For those patients, this sick-leave was associated to an extra-cost of 1,264-1,876 francs for Social Security and of 0-2,553 francs out of pocket per episode varying according to their Benefit Regimen.