Cooling of cylindrical vertical tanks submitted to natural internal convection

A numerical and an experimental analysis of velocity and temperature fields inside a storage tank submitted to natural convection is presented. The analysis was performed in two stages. In the first stage, the temperature profile along the vertical axis of the storage tank was obtained experimentally and numerically, for cooling time ranging from 45 to 60 h. The numerical analysis was carried out using a transient bi-dimensional model in cylindrical co-ordinates. In the second stage, after the numerical code validation, 40 cases of cooling with four aspect ratios, five insulation thicknesses, and two different volumes were simulated. In all simulations, thermal losses for the environment in all tank walls (side, top and bottom) were considered. Two correlations for the Nusselt number, encompassing all the forty cases, were obtained with these results.     

Structural properties and electrical behaviour of thin silicon oxynitride layers

Thin SiO₂ and SiO_xN_y layers were grown on silicon using Rapid Thermal Processing (RTP) in either O₂ or N₂O ambient. Subsequent annealing or nitridation was performed in order to improve the electrical stability. The composition of the films, in particular the incorporation of nitrogen and hydrogen, has been studied. We obtained the distribution of states at the Si/insulator interface through the evaluation of CV measurements and investigated the charge trapping in the layers analysing the voltage–time behaviour during Fowler–Nordheim constant current injection. Furthermore, assuming a trap assisted tunneling mechanism, the influence of near interface trap states on the current voltage characteristic was used to derive an effective insulator state distribution.     

Prenatal diagnostic testing for familial dysautonomia using linked genetic markers

Familial dysautonomia (FD), a recessively inherited disease, has been mapped to chromosome 9q31. Highly polymorphic dinucleotide repeat markers flanking the genetic locus and at the same genetic location have been identified. We describe the prenatal diagnosis of FD using linkage and linkage disequilibrium analyses with these markers. Twelve families were analysed for informativeness and of these, seven went on to have prenatal testing (a total of eight fetuses tested). All of these fetuses were predicted to be heterozygous unaffected (FD carriers). Seven fetuses have come to term and are normal. In the absence of a recombinant proband, a panel of three proximal and three distal markers is sufficient to provide informative flanking markers and an 87-96 per cent likelihood of a highly predictive test. In an additional family at 1:4 risk for FD, no DNA was available from the propositus. This family was analysed using linkage disequilibrium to the #18 allele of the tightly linked marker D9S58 in conjunction with linkage analysis using data from two unaffected children. Prenatal diagnosis in this family indicated an affected fetus.     

Hydroprocessing peculiarities of Fischer–Tropsch syncrude

When catalysts developed for crude oil hydroprocessing are used for syncrude, there are syncrude-specific peculiarities to consider. These relate to differences in the nature and abundance of heteroatoms, olefins, metal species, waxes and aqueous products. Some important aspects are (a) heat release during naphtha and distillate hydroprocessing is very high, but wax hydrocracking is almost isothermal; (b) syncrude is sulphur-free and the use of sulphided base-metal hydroprocessing catalysts require the addition of sulphur-containing compounds to the syncrude; (c) oxygenates strongly adsorb on some catalytic surfaces to affect catalytic behaviour; (d) carbonyl–carboxylic acid interconversion and water produced by hydrodeoxygenation (HDO) may result in catalyst degradation by acid and hydrothermal attack; (e) carboxylic acids in syncrude result in equipment corrosion and catalyst leaching; (f) metal carboxylates are the main metal-containing species in syncrude and are not removed by hydrodemetallation (HDM) catalysis, but by thermal decomposition.     

Bestimmung der Abtragungsraten von Zirconium,Tantal und der Legierung Tantal-40Niob in fluoridhaltiger azeotroper Salpetersäure mit Hilfe der Radiotracer-Methode

The radiotracer technique as a means to investigate the corrosion of zirconium, tantalum, and a Ta-40Nb alloy in fluoride containing azeotropic nitric acid Zirconium and tantalum as well as the tantalum 40% niobium alloy are of considerable technical importance due to their high corrosion resistance against numerous corrosive media. With respect to corrosion testing in analytically pure azeotropic nitric acid in the temperature range between 20 and 121°C, corrosion rates were determined for zirconium: 7 · 10^?6 to 5 · 10^?4 mm/y, for tantalum: 10^?8 to 4 · 10^?6 mm/y, and for the Ta-40Nb alloy: 2 · 10^?7 to 8 · 10^?6 mm/y [1]. These corrosion rates will be markedly increased by adding small amounts of fluorides or by fluoride impurities. The radiotracer method after neutron activation was applied to determine the corrosion rates in azeotropic fluoride containing nitric acid. Even minute additions of fluorides strongly affect the corrosion resistance of zirconium. In the range between 0.15 and 10 ppm F^? and at a temperature of 108°C, corrosion rates between 5.3 · 10^?3 and 3.1 mm/y were measured. It was impossible to establish a limit for the fluoride concentration, below which the corrosion rate of zirconium will not be adversely influenced. The corrosion rates of tantalum and the Ta-40Nb alloy are considerably increasing above a fluoride concentration of 10 ppm. The highest corrosion rates measured were between 8.4 · 10^?3 mm/y at 50°C/280 ppm F^? and 1.4 · 10^?2 mm/y at 110°C/320 ppm F^?. Within the range of this investigation, the corrosion resistance of tantalum was higher than that of the Ta-40Nb alloy by one order of magnitude. The corrosion resistance of zirconium and tantalum was not influenced by any treatment of the samples before testing.     

Percolation and eddy currents in random close packed metal polymer composites

Bare and copper-coated polystyrene (PS) beads are mixed to give various volume fractions of electrically conducting and insulating spheres. This random mixture is subsequently sintered under pressure in a hot dye. The resulting solid is a polymer body in which thin (0.3 m) copper shells form a tightly packed cellular cluster which exhibits electrical continuity. This continuity is detected by inductive coupling via eddy currents to a coil at r.f. frequency. The percolation threshold for both two- and three-dimensional systems is observed by changing the thickness of the samples in a range in which it is comparable to the size of the beads. The observed thresholds for percolation are in good agreement with the theory.     

IT Service Climate—An Essential Managerial Tool to Improve Client Satisfaction With IT Service Quality

Although client satisfaction surveys can assess client satisfaction with IT service quality, they cannot easily be used to pinpoint how internal IT behaviors influence client satisfaction and prescribe solutions. This research fills the gap by introducing a concept— IT Service Climate—and a validated ten-item instrument that significantly explained client ratings of IT service quality. We recommend this measure as an effective diagnostic tool for managers aiming to improve quality and client satisfaction.     

Processing and interactive editing of huge point clouds from 3D scanners

This paper describes a new out-of-core multi-resolution data structure for real-time visualization, interactive editing and externally efficient processing of large point clouds. We describe an editing system that makes use of the novel data structure to provide interactive editing and preprocessing tools for large scanner data sets. Using the new data structure, we provide a complete tool chain for 3D scanner data processing, from data preprocessing and filtering to manual touch-up and real-time visualization. In particular, we describe an out-of-core outlier removal and bilateral geometry filtering algorithm, a toolset for interactive selection, painting, transformation, and filtering of huge out-of-core point-cloud data sets and a real-time rendering algorithm, which all use the same data structure as storage backend. The interactive tools work in real-time for small model modifications. For large scale editing operations, we employ a two-resolution approach where editing is planned in real-time and executed in an externally efficient offline computation afterwards. We evaluate our implementation on example data sets of sizes up to 63 GB, demonstrating that the proposed technique can be used effectively in real-world applications.