A method of controlling anchoring energy of surface interaction of liquid crystal photoaligning substances is considered to enhance the liquid crystal display performances. An important parameter of the dye's molecular structure that determines the ratio of polar and azimuthal anchoring energy is the ability to form dimers. The values of dimerization thermodynamic potentials have been found. The probability of the formation of dye molecules dimers is evaluated. The bonds conjugation transfer via intermolecular hydrogen bond is revealed, and anisotropy of polarizability of the hydrogen bond is evaluated. The effect of dimerization on polar and azimuthal anchoring energy of liquid crystal — azo dye system — is shown. 相似文献
The performance of five hole-transporting layers (HTLs) is investigated in both single-junction perovskite and Cu(In, Ga)Se2 (CIGSe)-perovskite tandem solar cells: nickel oxide (NiOx,), copper-doped nickel oxide (NiOx:Cu), NiOx+SAM, NiOx:Cu+SAM, and SAM, where SAM is the [2-(3,-6Dimethoxy-9H-carbazol-9yl)ethyl]phosphonic acid (MeO-2PACz) self-assembled monolayer. The performance of the devices is correlated to the charge-carrier dynamics at the HTL/perovskite interface and the limiting factors of these HTLs are analyzed by performing time-resolved and absolute photoluminescence ((Tr)PL), transient surface photovoltage (tr-SPV), and X-ray/UV photoemission spectroscopy (XPS/UPS) measurements on indium tin oxide (ITO)/HTL/perovskite and CIGSe/HTL/perovskite stacks. A high quasi-Fermi level splitting to open-circuit (QFLS-Voc) deficit is detected for the NiOx-based devices, attributed to electron trapping and poor hole extraction at the NiOx-perovskite interface and a low carrier effective lifetime in the bulk of the perovskite. Simultaneously, doping the NiOx with 2% Cu and passivating its surface with MeO-2PACz suppresses the electron trapping, enhances the holes extraction, reduces the non-radiative interfacial recombination, and improves the band alignment. Due to this superior interfacial charge-carrier dynamics, NiOx:Cu+SAM is found to be the most suitable HTL for the monolithic CIGSe-perovskite tandem devices, enabling a power-conversion efficiency (PCE) of 23.4%, Voc of 1.72V, and a fill factor (FF) of 71%, while the remaining four HTLs suffer from prominent Voc and FF losses. 相似文献
Most in vitro iron mobilization studies from ferritin have been performed in aqueous buffered solutions using a variety of reducing substances. The kinetics of iron mobilization from ferritin in a medium that resembles the complex milieu of cells could dramatically differ from those in aqueous solutions, and to our knowledge, no such studies have been performed. Here, we have studied the kinetics of iron release from ferritin in fresh yeast cell lysates and examined the effect of cellular metabolites on this process. Our results show that iron release from ferritin in buffer is extremely slow compared to cell lysate under identical experimental conditions, suggesting that certain cellular metabolites present in yeast cell lysate facilitate the reductive release of ferric iron from the ferritin core. Using filtration membranes with different molecular weight cut-offs (3, 10, 30, 50, and 100 kDa), we demonstrate that a cellular component >50 kDa is implicated in the reductive release of iron. When the cell lysate was washed three times with buffer, or when NADPH was omitted from the solution, a dramatic decrease in iron mobilization rates was observed. The addition of physiological concentrations of free flavins, such as FMN, FAD, and riboflavin showed about a two-fold increase in the amount of released iron. Notably, all iron release kinetics occurred while the solution oxygen level was still high. Altogether, our results indicate that in addition to ferritin proteolysis, there exists an auxiliary iron reductive mechanism that involves long-range electron transfer reactions facilitated by the ferritin shell. The physiological implications of such iron reductive mechanisms are discussed. 相似文献
In this work, two medium Mn steels (5.8 and 5.7 wt pct Mn) were subjected to a quenching and partitioning (Q&P) treatment employing a partitioning temperature which corresponded to the start of austenite reverse transformation (ART). The influence of a 1.6 wt pct Ni addition in one of the steels and cycle parameters on austenite stability and mechanical properties was also studied. High contents of retained austenite were obtained in the lower quenching temperature (QT) condition, which at the same time resulted in a finer microstructure. The addition of Ni was effective in stabilizing higher contents of austenite. The partitioning of Mn and Ni from martensite into austenite was observed by TEM–EDS. The partitioning behaviour of Mn depended on the QT condition. The lower QT condition facilitated Mn enrichment of austenite laths during partitioning and stabilization of a higher content of austenite. The medium Mn steel containing Ni showed outstanding values of the product of tensile strength (TS) and total elongation (TEL) in the lower QT condition and a higher mechanical stability of the austenite.
The electroslag remelting (ESR) process is widely used to produce high-quality ingots and billets for high-alloyed steels and alloys.Both the single-phase and three-phase alternating current diagram with bifilar and monofilar connection are in use for heavy ingot manufacturing.The numerical simulation of the three-phase bifilar circuit for the 120 t three-phase bifilar six-electrode ESR furnace at different variants of electric connection was presented and discussed.At the bifilar diagram of power supply,the geometrical location of electrodes in a mould holds critical importance for performances:the close location of bifilar pair electrodes provides the highest heat productivity,but the equidistant location of electrodes gives a much more uniform heat distribution.The monofilar mulit-electrode diagram of three-phase connection without phase shift shows the most uniform distribution of potential and heat generation as well as a favorable magnetic field that makes this kind the most promising for providing a high quality of heavy ingots. 相似文献
High-temperature proton conductors based on acceptor-doped barium zirconate exhibit excellent chemical stability in atmospheres containing CO2 or H2O. However, due to their refractory nature, these conductors have a low grain growth rate, which negatively affects the overall electrical conductivity. A possible strategy for increasing the ionic conductivity of zirconates lies in the partial substitution of Zr-ions with other isovalent dopants. In this work, we carried out systematic studies of the crystal structure, microstructure, hydration capacity, transport, and thermal properties of BaZr0.8–xSnxSc0.2O3–δ (x = 0, 0.1, and 0.2). According to X-ray powder diffraction and scanning electron microscopy data, all studied ceramic samples have a cubic perovskite structure, whose average grain size decreases with tin doping. It is found that the composition with x = 0.1 exhibits the highest values in terms of total, ionic, grain, and grain-boundary conductivities. The complex analysis of the obtained data shows that a low-level substitution of Zr4+- with Sn4+-ions is a competent approach for designing new proton-conducting electrolytes attractive for high-temperature applications. 相似文献
A novel microporous two-dimensional(2D)Ni-based phosphonate metal-organic framework(MOF;denoted as IEF-13)has been successfully synthesized by a simple and green hydrothermal method and fully characterized using a combination of experimental and computational techniques.Structure resolution by single-crystal X-ray diffraction reveals that IEF-13 crystallizes in the triclinic space group Pi having bi-octahedra nickel nodes and a photo/electroactive tritopic phosphonate ligand.Remarkably,this material exhibits coordinatively unsaturated nickel(II)sites,free-P03H2and-P03H acidic groups,a C02accessible microporosity,and an exceptional thermal and chemical stability.Further,its in-deep optoelectronic characterization evidences a photoresponse suitable for photocatalysis.In this sense,the photocatalytic activity for challenging H2generation and overall water splitting in absence of any co-catalyst using UV-Vis irradiation and simulated sunlight has been evaluated,constituting the first report for a phosphonate-MOF photocatalyst.IEF-13 is able to produce up to 2,200 fimol of H2per gram using methanol as sacrificial agent,exhibiting stability,maintaining its crystal structure and allowing its recycling.Even more,170μmol of H2per gram were produced using IEF-13 as photocatalyst in the absence of any co-catalyst for the overall water splitting,being this reaction limited by the 02reduction.The present work opens new avenues for further optimization of the photocatalytic activity in this type of multifunctional materials. 相似文献