Differential Game for Distributed Power Control in Device-to-Device Communications Underlaying Cellular Networks

Wireless Personal Communications - In the formulating of power control for wireless networks, the radio channel is commonly formulated using static models of optimization or game theory. In these...     

Improvement in hydrolytic procedure for GLC determination of non-indolyl glucosinolates in rapeseed as isothiocyanates

Some methods determine the non-indolyl glucosinolates content in rapeseed as their hydrolysates: the isothiocyanates and the oxazolidinethiones. These methods in their present form underestimate the amount of the glucosinolates content. In this investigation, a modified method was developed to give a better quantitative estimate, indicating a glucosinolate level five times that obtained by a typical existing method.     

Thickness-dependence of stoichiometry and microstructure characteristics in correlation with conductivity type of CdTe films

CdTe films were prepared by physical vapour deposition on a substrate at room temperature (RT) as well as on a cold (LT) one using low deposition rate. The thickness-dependence of stoichiometry revealed an abrupt decrease in the Cd/Te ratio as the thickness increases. Change of thickness did not affect the type of observed (111) crystallographic texture, only the degree of preferred orientation is enhanced as the film grows. The internal strain was negligible while the crystallite size increased rapidly at small thickness (up to 400 nm), and less thickness dependence was observed with further film growth. However, thickness dependence of lattice parameters showed a minimum and a maximum at approximately 300 nm in the case of RT and LT, respectively. The observed change in conductivity from n- to p-type and its vital correlation with the stoichiometry and structural characteristics were presented. Based on thickness dependence of stoichiometry and lattice parameters as well as the conductivity type, formation and annihilation of lattice defects were considered.     

Modelling and controller design of an isolated diesel enginepermanent magnet synchronous generator

A method to analyze the steady-state performance of a stand-alone permanent magnet synchronous generator driven by a diesel engine is presented. The proposed method is based on equivalent d-q circuits and the phasor diagram of such a generator under steady-state conditions. A fixed capacitor-thyristor controlled reactor scheme is used to regulate the generator terminal voltage by controlling the thyristor ignition angle. Furthermore the overall system dynamics are modelled in terms of state variables and control inputs. Based on a reduced order linearized model, digital optimal state and output feedback controllers are designed by minimising a quadratic performance index using the dynamic programming technique. The objective of the controller is to maintain the load voltage and frequency constant under varying load conditions. The controller's effectiveness is assessed by examining the closed-loop system response to sudden load changes     

Effect of electron irradiation on alternating current electrical properties of gelatin – cadmium sulfide nano-composite films

Gelatin was doped with 1 %, 3 %, 5 % and 10 % cadmium sulfide nanoparticles in weight concentrations forming the gelatin-cadmium sulfide nanocomposites and irradiated by various electron beam doses equals 50 kGy, 75 kGy, 100 kGy, and 150 kGy using 3 MeV – 3 mA electron accelerator. The applied alternating current electrical field frequency ranging from 70 Hz to 5 MHz is what caused the fluctuation in dielectric properties and alternating current electrical conductivity of these nanocomposites. The results showed that the films of 1 %, 3 %, 5 %, and 10 % for blank (nanocomposite film without electron beam irradiation) nanocomposites had the highest dielectric parameters (έ, ϵ′′, tan δ) at 0.5 kHz with values of (0.696, 0.0233, 0.034), (0.533, 0.0114, 0.0215), (0.402, 0.001196, 0.003), and (0.459, 0.00418, 0.0091), respectively. However, the lowest dielectric parameters were (0.645, 0.00618, 0.0066), (0.523, 0.00165, 0.0215), (0.417, 0.00035, 0.0008), and (0.455, 0.00066, 0.0015) at 5 MHz, respectively. The highest conductivity values for blank nanocomposites of 1 %, 3 %, 5 %, and 10 % were 1.79×10⁻⁴ S/m, 1.45×10⁻⁴ S/m, 1.16×10⁻⁴ S/m, 1.27×10⁻⁴ S/m at 5 MHz, and the lowest values were 1.92×10⁻⁸ S/m, 1.49×10⁻⁸ S/m, 1.13×10⁻⁸ S/m, 1.26×10⁻⁸ S/m at 0.5 kHz, respectively. For irradiated nanocomposites at 5 MHz, the dielectric constant order for 1 % was 100 kGy, 150 kGy, 50 kGy, and 75 kGy with values 0.63, 0.537, 0.532, and 0.523, respectively. For 10 % weight concentration, the order was 50 kGy, 100 kGy, 150 kGy, and 75 kGy with values 0.515, 0.477, 0.47, and 0.437, respectively. Otherwise the dielectric constant order for 3 % and 5 % was 100 kGy, 75 kGy, 150 kGy, and 50 kGy. The highest dielectric properties and conductivity values for blank and irradiated nanocomposites were observed at 100 kGy for 1 %, 3 %, and 5 %.     

A new expert system for learning management systems evaluation based on neutrosophic sets

There has been a sudden increase in the usage of Learning Management Systems applications to support learner's learning process in higher education. Many studies in learning management system evaluation are implemented under complete information, while the real environment has uncertainty aspects. As these systems were described by development organizations with uncertainty terms such as vague, imprecise, ambiguity and inconsistent, that is why traditional evaluation methods may not be effective. This paper suggests neutrosophic logic as a better option to simulate human thinking than fuzzy logic because unlike fuzzy logic, it is able to handle indeterminacy of information which expresses the percentage of unknown parameters. As previous studies suggested neutrosophic decision maker and neutrosophic expert systems as future work in ecommerce and e‐learning applications, this paper presents neutrosphic expert system for learning management systems evaluation. Information for building and validating the neutrosophic expert system is collected from five experts using surveys, and then analysis is done by using Fuzzytech 5.54d software. Finally, the comparison between fuzzy expert system and neutrosophic expert system results show that the neutrosophic logic is capable of representing uncertainty in human thinking for evaluating Learning Management Systems.     

Computerized relational model for powder technology: powder and process selection

Part of a complete expert-system software design for powder technology is presented. This part of the system deals with powder selection according to predetermined, recommended or required material properties, and specific powder characteristics. Then the optimum powder production, i.e processing, method is determined, which satisfies the requirements of the specified powder. For this purpose a detailed database relational model is developed, and the system's software modules are described. A relational model is formulated and a structured query language (SQL) is used in the detailed software design presented.     

Wheel Load Distribution in Simply Supported Concrete Slab Bridges

This paper presents the results of a parametric study related to the wheel load distribution in one-span, simply supported, multilane, reinforced concrete slab bridges. The finite-element method was used to investigate the effect of span length, slab width with and without shoulders, and wheel load conditions on typical bridges. A total of 112 highway bridge case studies were analyzed. It was assumed that the bridges were stand-alone structures carrying one-way traffic. The finite-element analysis (FEA) results of one-, two-, three-, and four-lane bridges are presented in combination with four typical span lengths. Bridges were loaded with highway design truck HS20 placed at critical locations in the longitudinal direction of each lane. Two possible transverse truck positions were considered: (1) Centered loading condition where design trucks are assumed to be traveling in the center of each lane; and (2) edge loading condition where the design trucks are placed close to one edge of the slab with the absolute minimum spacing between adjacent trucks. FEA results for bridges subjected to edge loading showed that the AASHTO standard specifications procedure overestimates the bending moment by 30% for one lane and a span length less than 7.5 m (25 ft) but agrees with FEA bending moments for longer spans. The AASHTO bending moment gave results similar to those of the FEA when considering two or more lanes and a span length less than 10.5 m (35 ft). However, as the span length increases, AASHTO underestimates the FEA bending moment by 15 to 30%. It was shown that the presence of shoulders on both sides of the bridge increases the load-carrying capacity of the bridge due to the increase in slab width. An extreme loading scenario was created by introducing a disabled truck near the edge in addition to design trucks in other lanes placed as close as possible to the disabled truck. For this extreme loading condition, AASHTO procedure gave similar results to the FEA longitudinal bending moments for spans up to 7.5 m (25 ft) and underestimated the FEA (20 to 40%) for spans between 9 and 16.5 m (30 and 55 ft), regardless of the number of lanes. The new AASHTO load and resistance factor design (LRFD) bridge design specifications overestimate the bending moments for normal traffic on bridges. However, LRFD procedure gives results similar to those of the FEA edge+truck loading condition. Furthermore, the FEA results showed that edge beams must be considered in multilane slab bridges with a span length ranging between 6 and 16.5 m (20 and 55 ft). This paper will assist bridge engineers in performing realistic designs of simply supported, multilane, reinforced concrete slab bridges as well as evaluating the load-carrying capacity of existing highway bridges.     

Separation and preconcentration of La from monazite, followed by determination using nondestructive γ-ray spectrometry

A method was developed for separation, preconcentration, and determination of La by its radioactive isotope ¹³⁸La using an HPGe detector. The method was checked by comparison with ICP-MS. The detection limit (minimum detection activity) is 1.46 and 1.52 Bq kg^?1 at 788.4 and 1435.8 keV lines, respectively. The Th(IV) and U(VI) are separated by precipitation. To separate Ac(III), it is extracted jointly with REEs from 0.1 M HNO₃ with HDEHP and then stripped with 0.2 M HNO₃, with REEs remaining in the organic phase. Lanthanum in a mixture with REEs is determined by ??-ray spectrometry.