Service life planning and performance requirements

Service life planning comprises a model for the determination of a reasonable expected service life for buildings and components, and it establishes a routine for the assessment of design alternatives. A design option is considered reasonable when it meets or exceeds performance requirements over time that have been drawn up specifically for the specific project. Due to this assessment reference, there is a very evident link to the concept of performance-based building. Any stakeholder involved in the value chain or in the design process of the building, as well as regulators and building users, can express performance requirements. Identified requirements, both in relevance and in quality, will vary with the stakeholder and his/her perspective of interest. As building sector manufacturers develop most products with reference to standards rather than with reference to specific requirements, there is no direct link from user requirements to the product design. Instead, the building designer has the responsibility to ensure performance requirements are met by the performance of products integrated into the design. As these design decisions also have to be made at the material and component level, a performance-based building would benefit from an established rationale that enables the communication of performance requirements across the relevant system levels in the relevant design processes. A path for the connection of the established concepts of service life planning and performance-based building is presented. The aim is to identify key elements that need to be developed for the successful linkage of performance-based building with service life planning.     

State-variable planning under structural restrictions: algorithms and complexity

Computationally tractable planning problems reported in the literature so far have almost exclusively been defined by syntactical restrictions. To better exploit the inherent structure in problems, it is probably necessary to study also structural restrictions on the underlying state-transition graph. The exponential size of this graph, though, makes such restrictions costly to test. Hence, we propose an intermediate approach, using a state-variable model for planning and defining restrictions on the separate state-transition graphs for each state variable. We identify such restrictions which can tractably be tested and we present a planning algorithm which is correct and runs in polynomial time under these restrictions. The algorithm has been implemented and it outperforms Graphplan on a number of test instances. In addition, we present an exhaustive map of the complexity results for planning under all combinations of four previously studied syntactical restrictions and our five new structural restrictions. This complexity map considers both the optimal and non-optimal plan generation problem.     

Ecological effects of river regulation on mammals and birds: A review

Although most of the world's river systems are regulated, the effects of river regulation on mammals and birds are little known. In fact, speculations are more common than empirical data. A review of this topic is presented, emphasizing northern rivers where most impacts have been described. Effects are related to the major causes of change. It is concluded that the two most disastrous effects of river regulation on mammals and birds are the permanent inundation of vast areas of land, and the disruption of the seasonal flood regime along the river. The design of future investigations to improve our knowledge is considered.     

An addressable 256×256 photodiode image sensor array with an 8-bit digital output

We have constructed an addressable 256 × 256 photodiode sensor array together with an 8-bit ADC (analog-to-digital converter) on the same chip. Such a digital camera is easy to connect to a computer where also the flexibility of the computer can be used to control the camera output. The sensor has been constructed in two versions. The first version was implemented with a 256-column parallel-bit-slice image processor on the same die in a commercial project and the second as a separate addressable digital image sensor. The sensor was functionally fabricated using 1.6 µm design rules in a 1.2 µm CMOS process where it required a total area of 96 mm².     

Power consumption of analog circuits: a tutorial

A systematic approach to the power consumption of analog circuits is presented. The power consumption is related to basic circuit requirements, as dynamic range, bandwidth, noise figure and sampling speed and is considering basic device and device scaling behavior. Several kinds of circuits are treated, as samplers, amplifiers, filters and oscillators. The objective is to derive lower bounds to power consumption in analog circuits, to be used as design targets when designing power-constrained analog systems.     

A readout IC for an uncooled microbolometer infrared FPA with on-chip self-heating compensation in 0.35 μm CMOS

This paper describes a readout integrated circuit architecture for an infrared focal plane array intended for infrared network-attached video cameras in surveillance applications. The focal plane array consists of 352 × 288 uncooled thin-film microbolometer detectors with a pitch of 25 μm, enabling ambient temperature operation. The circuit features a low-noise readout path, detector resistance mismatch correction and a non-linear ramped current pulse scheme for the electrical biasing of the detectors in order to relax the dynamic range requirement of amplifiers and the ADC in the readout channel, imposed by detector process variation and self-heating during readout. The design is implemented in a 0.35-μm standard CMOS process and two versions of a smaller 32 × 32-pixel test chip have been fabricated and measured for evaluation. The latest test chip achieves a dynamic range of 97 dB and an input-referred RMS noise voltage of 6.4 μV yielding an estimated NETD value of 26 mK with f/1 optics. At a frame rate of 60 FPS the chip dissipates 170 mW of power from a 3.4 V supply.     

Effect of fuel injection pressure on a heavy-duty diesel engine nonvolatile particle emission

The effects of the fuel injection pressure on a heavy-duty diesel engine exhaust particle emissions were studied. Nonvolatile particle size distributions and gaseous emissions were measured at steady-state engine conditions while the fuel injection pressure was changed. An increase in the injection pressure resulted in an increase in the nonvolatile nucleation mode (core) emission at medium and at high loads. At low loads, the core was not detected. Simultaneously, a decrease in soot mode number concentration and size and an increase in the soot mode distribution width were detected at all loads. Interestingly, the emission of the core was independent of the soot mode concentration at load conditions below 50%. Depending on engine load conditions, growth of the geometric mean diameter of the core mode was also detected with increasing injection pressure. The core mode emission and also the size of the mode increased with increasing NOx emission while the soot mode size and emission decreased simultaneously.     

Lignin gels as a medium in gel permeation chromatography

The preparation of spherical lignin gel beads, based on the crosslinking reaction between epichlorohydrin and kraft lignin (Indulin AT), is described. The lignin gels prepared were found to be an efficient resin in gel permeation chromatography. The separation of polystyrenes in dimethylformamide is described. The resin was found to separate polystyrenes with molecular weights up to 110,000. An inverse linear relationship between log M and elution volume or the partitioning coefficient was established.     

Pheromonal secretions from glands on the 5th abdominal sternite of hydropsychid and rhyacophilid caddisflies (Trichoptera)

Extracts of different body parts of adult Trichoptera were tested for electrophysiological activity. Extracts of the IVth and Vth abdominal sternites of femaleHydropsyche angustipennis, Rhyacophila nubila, andR. fasciata, containing a paired exocrine gland, elicited significant electroan-tennographic responses when tested on conspecific male antennae. The paired gland occurs also in males of all the species, and inH. angustipennis, extracts from males were more active than female extracts when tested on male antennae. Female and male extracts from all species were analyzed by gas chromatography with simultaneous flame ionization and electroantennographic detection (EAD). EAD-active peaks in female extracts, stimulating male antennae, were identified inH. angustipennis as nonan-2-one; and inR. nubila andR. fasciata as heptan-2-one, heptan-2-ol, nonan-2-one, and nonan-2-ol. EAD-active components from maleH. angustipennis stimulating male antennae were octan-2-one, nonan-2-one (major peak), (Z)-6-nonen-2-one, decan-2-one, and a methylbranched decan-2-one. Female extracts and synthetic mixtures of compounds identified from femaleH. angustipennis andR. fasciata were tested for attractivity in the field. High catches with control traps obscured the results, but a synthetic mixture of the four identified compounds was significantly attractive and not different from female extracts for attracting maleR. fasciata. InH. angustipennis, a synthetic six-component male blend, in which nonan-2-one was the major component, attracted significant numbers of male and femaleH. angustipennis. Extracts of maleR. nubila andR. fasciata contained acetophenone and hexanoic and octanoic acids but did not have any electrophysiological or behavioral activity on either male or female antennae of conspecifics. The occurrence of a female sex pheromone inRhyacophila and an aggregation pheromone inHydropsyche corresponds to earlier described differences in mating behaviors in the Rhyacophilidae and Hydropsychidae.     

Conversion of microwave pyrolysed ASR's char using high temperature agents

Pyrolysis enables to recover metals and organic feedstock from waste conglomerates such as: automotive shredder residue (ASR). ASR as well as its pyrolysis solid products, is a morphologically and chemically varied mixture, containing mineral materials, including hazardous heavy metals. The aim of the work is to generate fundamental knowledge on the conversion of the organic residues of the solid products after ASR's microwave pyrolysis, treated at various temperatures and with two different types of gasifying agent: pure steam or 3% (v/v) of oxygen. The research is conducted using a lab-scale, plug-flow gasifier, with an integrated scale for analysing mass loss changes over time of experiment, serving as macro TG at 950, 850 and 760 °C. The reaction rate of char decomposition was investigated, based on carbon conversion during gasification and pyrolysis stage. It was found in both fractions that char conversion rate decreases with the rise of external gas temperature, regardless of the gasifying agent. No significant differences between the reaction rates undergoing with steam and oxygen for char decomposition has been observed. This abnormal char behaviour might have been caused by the inhibiting effects of ash, especially alkali metals on char activity or due to deformation of char structure during microwave heating.