Comparative study of Fourier transform infrared spectroscopy (FTIR) analysis of natural fibres treated with chemical,physical and biological methods

Polymer Bulletin - Kenaf and luffa fibres are hydrophilic due to the presence of water sensitive constituents, which tend to form a poor compatibility when binding with polymers. Thus, the surface...     

Multiply Charged Conjugated Polyelectrolytes as a Multifunctional Interlayer for Efficient and Scalable Perovskite Solar Cells

A series of anionic conjugated polyelectrolytes (CPEs) is synthesized based on poly(fluorene-co-phenylene) by varying the side-chain ionic density from two to six per repeat units (MPS2-TMA, MPS4-TMA, and MPS6-TMA). The effect of MPS2, 4, 6-TMA as interlayers on top of a hole-extraction layer of poly(bis(4-phenyl)-2,4,6-trimethylphenylamine (PTAA) is investigated in inverted perovskite solar cells (PeSCs). Owing to the improved wettability of perovskites on hydrophobic PTAA with the CPEs, the PeSCs with CPE interlayers demonstrate a significantly enhanced device performance, with negligible device-to-device dependence relative to the reference PeSC without CPEs. By increasing the ionic density in the MPS-TMA interlayers, the wetting, interfacial defect passivation, and crystal growth of the perovskites are significantly improved without increasing the series resistance of the PeSCs. In particular, the open-circuit voltage increases from 1.06 V for the PeSC with MPS2-TMA to 1.11 V for the PeSC with MPS6-TMA. The trap densities of the PeSCs with MPS2,4,6-TMA are further analyzed using frequency-dependent capacitance measurements. Finally, a large-area (1 cm²) PeSC is successfully fabricated with MPS6-TMA, showing a power conversion efficiency of 18.38% with negligible hysteresis and a stable power output under light soaking for 60 s.     

Molecular structure and granule morphology of native and heat‐moisture‐treated pinhão starch

Pinhão seed is an unconventional source of starch and the pines grow up in native forests of southern Latin America. In this study, pinhão starch was adjusted at 15, 20 and 25% moisture content and heated to 100, 110 and 120 °C for 1 h. A decrease in λ max (starch/iodine complex) was observed as a result of increase in temperature and moisture content of HMT. The ratio of crystalline to amorphous phase in pinhão starch was determined via Fourier transform infra red by taking 1045/1022 band ratio. A decrease in crystallinity occurred as a result of HMT. Polarised light microscopy indicated a loss of birefringence of starch granules under 120 °C at 25% moisture content. Granule size distribution was further confirmed via scanning electron microscopy which showed the HMT effects. These results increased the understanding on molecular and structural properties of HMT pinhão starch and broadened its food and nonfood industrial applications.     

Annotation alignment method on P2P-TV system

Peer-to-Peer Networking and Applications - P2P-TV is a TV system that receives content through a peer-to-peer network. Content is stored in the distributed manner then to be serviced to users, and...     

Hydroxyapatite/tricalcium silicate composites cement derived from novel two-step sol-gel process with good biocompatibility and applications as bone cement and potential coating materials

Tricalcium silicate (C₃S) and hydroxyapatite (HAp) composites were fabricated through the sol-gel process. The aim of this research is to improve the biocompatibility of C₃S through HAp addition and study the potential of using this as coating materials. The composites (HAp/C₃S) were characterised by Fourier transform infrared spectrometry, thermal gravity-differential thermal analysis and X-ray diffraction. The working and setting times of cement pastes were tested using Gillmore needle. Mechanical properties were examined by nanoindentation and material testing system. In vitro biocompatibility of the materials were studied by cell attachment and viability of L929 and MG-63 cells. HAp/C₃S as a coating material on gelatin film were measured with the surface roughness and imaged by scanning electron microscope. With the addition of HAp, no undesirable free CaO was detected with the synthesis by the sol-gel preparation. The pH values of HAp added groups were between 7.54 and 8.76, which were much lower than pure C₃S group (pH?=?11.75). For in vitro studies, the presence of HAp could effectively enhance the cell attachment and viability of both L929 and MG-63 cells grown in the extract or directly on the composites. However, the mechanical properties of the composites were impaired as compared to pure C₃S. Lastly, HAp/C₃S cement could be evenly coated on gelatin film. HAp is successfully demonstrated to improve C₃S biocompatibility with this new composites HAp/C₃S. C-75 (75% C₃S and 25% HAp), in particular, has good biocompatibility, relatively high compressive strength and can be uniformly coated onto gelatin film. Thus, C-75 is a promising material for further investigation as a coating on other biopolymers.     

Back-analysis of geotechnical parameters on PVD-improved ground in the Mekong Delta

This study presents a back-analysis of geotechnical parameters on prefabricated vertical drain improved ground at a site in the Mekong Delta. Various time?settlement behaviors that reflected different clay thicknesses and loading patterns were observed. The total surface settlement behavior at several monitoring locations was simulated using an updated exponential method that considered staged construction. The analyzed results were validated by substituting the values into a theoretical solution for radial consolidation. The estimated theoretical behaviors were comparable with the monitored behaviors. The geotechnical parameters were back-analyzed by applying the previously analyzed results to various theoretical and empirical formulas. However, the use of extensometer data that were installed at large intervals produced different values of the geotechnical properties. Furthermore, finite element analysis supported the back-analyzed total settlement behaviors and nearly disregarded the application of the geotechnical properties that were obtained using either surface or subsurface settlement data. However, settlements and excess pore pressures in the sublayers were not successfully predicted even when the geotechnical properties were adjusted. Thus, subsurface instruments that can be installed closely in thick clay deposits are required to reliably reevaluate the variations in geotechnical properties along a certain depth.     

Understanding trust in ms-commerce: The roles of reported experience,linguistic style,profile photo,emotional, and cognitive trust

This paper examines what influences trust in mobile social commerce environment. Drawing on trust-based acceptance model (i.e. cognitive and emotional trust) and online review features (i.e. profile photo, linguistic style, and reported experience), we examine how these factors affect trust in mobile social commerce. Hypotheses were tested using survey data. The results of our model showed that there are significant influences of profile photo, reported experience, cognitive, and emotional trust towards trust in ms-commerce. This work contributes to existing literature by examining the roles of previous trust in mobile payments and online reviews on trust in mobile social commerce.