Multiply Charged Conjugated Polyelectrolytes as a Multifunctional Interlayer for Efficient and Scalable Perovskite Solar Cells

A series of anionic conjugated polyelectrolytes (CPEs) is synthesized based on poly(fluorene-co-phenylene) by varying the side-chain ionic density from two to six per repeat units (MPS2-TMA, MPS4-TMA, and MPS6-TMA). The effect of MPS2, 4, 6-TMA as interlayers on top of a hole-extraction layer of poly(bis(4-phenyl)-2,4,6-trimethylphenylamine (PTAA) is investigated in inverted perovskite solar cells (PeSCs). Owing to the improved wettability of perovskites on hydrophobic PTAA with the CPEs, the PeSCs with CPE interlayers demonstrate a significantly enhanced device performance, with negligible device-to-device dependence relative to the reference PeSC without CPEs. By increasing the ionic density in the MPS-TMA interlayers, the wetting, interfacial defect passivation, and crystal growth of the perovskites are significantly improved without increasing the series resistance of the PeSCs. In particular, the open-circuit voltage increases from 1.06 V for the PeSC with MPS2-TMA to 1.11 V for the PeSC with MPS6-TMA. The trap densities of the PeSCs with MPS2,4,6-TMA are further analyzed using frequency-dependent capacitance measurements. Finally, a large-area (1 cm²) PeSC is successfully fabricated with MPS6-TMA, showing a power conversion efficiency of 18.38% with negligible hysteresis and a stable power output under light soaking for 60 s.     

Annotation alignment method on P2P-TV system

Peer-to-Peer Networking and Applications - P2P-TV is a TV system that receives content through a peer-to-peer network. Content is stored in the distributed manner then to be serviced to users, and...     

Hydroxyapatite/tricalcium silicate composites cement derived from novel two-step sol-gel process with good biocompatibility and applications as bone cement and potential coating materials

Tricalcium silicate (C₃S) and hydroxyapatite (HAp) composites were fabricated through the sol-gel process. The aim of this research is to improve the biocompatibility of C₃S through HAp addition and study the potential of using this as coating materials. The composites (HAp/C₃S) were characterised by Fourier transform infrared spectrometry, thermal gravity-differential thermal analysis and X-ray diffraction. The working and setting times of cement pastes were tested using Gillmore needle. Mechanical properties were examined by nanoindentation and material testing system. In vitro biocompatibility of the materials were studied by cell attachment and viability of L929 and MG-63 cells. HAp/C₃S as a coating material on gelatin film were measured with the surface roughness and imaged by scanning electron microscope. With the addition of HAp, no undesirable free CaO was detected with the synthesis by the sol-gel preparation. The pH values of HAp added groups were between 7.54 and 8.76, which were much lower than pure C₃S group (pH?=?11.75). For in vitro studies, the presence of HAp could effectively enhance the cell attachment and viability of both L929 and MG-63 cells grown in the extract or directly on the composites. However, the mechanical properties of the composites were impaired as compared to pure C₃S. Lastly, HAp/C₃S cement could be evenly coated on gelatin film. HAp is successfully demonstrated to improve C₃S biocompatibility with this new composites HAp/C₃S. C-75 (75% C₃S and 25% HAp), in particular, has good biocompatibility, relatively high compressive strength and can be uniformly coated onto gelatin film. Thus, C-75 is a promising material for further investigation as a coating on other biopolymers.     

Back-analysis of geotechnical parameters on PVD-improved ground in the Mekong Delta

This study presents a back-analysis of geotechnical parameters on prefabricated vertical drain improved ground at a site in the Mekong Delta. Various time?settlement behaviors that reflected different clay thicknesses and loading patterns were observed. The total surface settlement behavior at several monitoring locations was simulated using an updated exponential method that considered staged construction. The analyzed results were validated by substituting the values into a theoretical solution for radial consolidation. The estimated theoretical behaviors were comparable with the monitored behaviors. The geotechnical parameters were back-analyzed by applying the previously analyzed results to various theoretical and empirical formulas. However, the use of extensometer data that were installed at large intervals produced different values of the geotechnical properties. Furthermore, finite element analysis supported the back-analyzed total settlement behaviors and nearly disregarded the application of the geotechnical properties that were obtained using either surface or subsurface settlement data. However, settlements and excess pore pressures in the sublayers were not successfully predicted even when the geotechnical properties were adjusted. Thus, subsurface instruments that can be installed closely in thick clay deposits are required to reliably reevaluate the variations in geotechnical properties along a certain depth.     

Nonlinear system identification using BBO-based multilayer perceptron network method

Microsystem Technologies - Recently, nonlinear system identification has received increasingly more attention due to its promising applications in engineering fields. It has become a challenging...     

Development of core mode blocker with H/sub 2/-loaded Ge-B codoped fibres

A novel fabrication method of the core mode blocker by exposing H/sub 2/-loaded Ge-B codoped fibres to local electric arc discharge for application to the LPFGs-based tunable all-fibre bandpass filter with 6.5 nm bandwidth and 40 nm tuning range is presented.     

Synthesis and characterization of conducting copolymers from aniline and o‐anisidine in HCl solutions

Conducting poly(aniline‐co‐o‐anisidine) (PAS) films with different ratios of aniline units in the polymer chain were prepared by oxidative polymerization of different molar ratios of aniline and o‐anisidine in 1 M HCl using cyclic voltammetry. Due to the much higher reactivity of o‐anisidine, the structure and properties of PASs were found to be dominated by the o‐anisidine units. The polymerization of poly‐o‐anisidine and PASs followed zero‐order kinetics with respect to formation of the polymer (film thickness) and the autocatalytic polymerization of aniline was completely inhibited. In contrast to polyaniline, a decrease in the polymerization temperature was found to increase the amount of copolymer formed and its redox charge. The presence of aniline units in PASs led to a pronounced increase in the molecular weight and conductivity, and a decrease in the solubility in organic solvents. Repetitive charging/discharging cycles showed that PASs resist degradation more than polyaniline. Copyright © 2003 Society of Chemical Industry